Allied-telesis AT-S94 CLI (AT-8000S Series) Manual de usuario

613-001983 Rev. AManagementSoftwareAT-S94CLI User’s GuideAT-8000S Series Stackable Gigabit Ethernet SwitchesVersion 3.0.0.45

Page 9 Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidesnmp-server enable traps...

Page 99Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.Example The fol

Ethernet Configuration CommandsPage 100Chapter 8. Ethernet Configuration Commandsinterface ethernetThe interface ethernet Global Configuration mode co

Page 101Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesCommands under the inte

Ethernet Configuration CommandsPage 102descriptionThe description Interface Configuration (Ethernet, port-channel) mode command adds a description to

Page 103Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeInterface Configuration (Ethernet, port-channel) modeUser Guide

Ethernet Configuration CommandsPage 104ExampleThe following example configures the duplex operation of Ethernet port 1/e5 to full duplex operation.neg

Page 105Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•on — Force flow control as enabled.• off — Force flow control as

Ethernet Configuration CommandsPage 106ExampleIn the following example, automatic crossover is enabled on port 1/e5.back-pressureThe back-pressure Int

Page 107Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command Mode

Ethernet Configuration CommandsPage 108Parameters•interface — Valid Ethernet port. (Full syntax: unit/port)• port-channel-number — Valid port-channel

Page 10ip ssh server...

Page 109Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow interfaces configurationThe show interfaces configuration Privileged E

Ethernet Configuration CommandsPage 110ExampleThe following example displays the configuration of all configured interfaces:show interfaces statusThe

Page 111Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines

Ethernet Configuration CommandsPage 112Parameters•interface — Valid Ethernet port. (Full syntax: unit/port)• port-channel-number — A valid port-channe

Page 113Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModesUser EXEC modeUser GuidelinesThere are no user guidelines for

Ethernet Configuration CommandsPage 114The following table describes the fields shown in the display:ch70000ch80000console#console# show interfaces co

Page 115Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideport storm-control include-multicast (IC)The port storm-control include-mul

Ethernet Configuration CommandsPage 116Syntaxport storm-control broadcast enableno port storm-control broadcast enableParametersThis command has no ar

Page 117Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser GuidelinesUse the port storm-control broadcast enable Interface Config

GVRP CommandsPage 118Chapter 9. GVRP Commandsgvrp enable (Global)GARP VLAN Registration Protocol (GVRP) is an industry-standard protocol designed to p

Page 11 Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidereload...

Page 119Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationGVRP is disabled on all interfaces.Command ModeInterfa

GVRP CommandsPage 120Set the same GARP timer values on all Layer 2-connected devices. If the GARP timers are set differently on Layer 2-connected devi

Page 121Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideno gvrp registration-forbidDefault ConfigurationDynamic registration of VLA

GVRP CommandsPage 122Syntaxshow gvrp configuration [ethernet interface | port-channel port-channel-number]Parameters•interface — A valid Ethernet port

Page 123Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxshow gvrp statistics [ethernet interface | port-channel port-channel-

GVRP CommandsPage 124Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThere are no user guideli

Page 125Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 10.IGMP Snooping CommandsNoteIn order to enable IGMP snooping, the

IGMP Snooping CommandsPage 126ParametersThis command has no arguments or keywords.Default ConfigurationIGMP snooping is disabled .Command ModeInterfac

Page 127Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example enables automatic learning of Multicast device

IGMP Snooping CommandsPage 128ip igmp snooping host-time-outThe ip igmp snooping host-time-out Interface Configuration (VLAN) mode command configures

Page 12show vlan ...

Page 129Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeInterface Configuration (VLAN) modeUser GuidelinesIGMP snooping

IGMP Snooping CommandsPage 130Example.The following example configures the source IP address that the IGMP Snooping querier uses. ip igmp snooping que

Page 131Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideno ip igmp snooping mrouter-time-outParameters•time-out — Multicast device

IGMP Snooping CommandsPage 132Use immediate leave only where there is just one host connected to a port. ExampleThe following example configures the h

Page 133Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxshow ip igmp snooping interface vlan-idParameters•vlan-id — VLAN numb

IGMP Snooping CommandsPage 134show ip igmp snooping groupsThe show ip igmp snooping groups command displays the Multicast groups that was learned by t

Page 135Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 11.IP Addressing Commandsip addressThe ip address Interface Configu

IP Addressing CommandsPage 136Parameters•host-name — Specifies the name of the host to be placed in the DHCP option 12 field. This name does not have

Page 137Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationNo default gateway is defined.Command ModeGlobal Confi

IP Addressing CommandsPage 138arp The arp Global Configuration mode command adds a permanent entry in the Address Resolution Protocol (ARP) cache. Use

Page 13 Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide

Page 139Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideno arp timeoutParameters•seconds — Time (in seconds) that an entry remains

IP Addressing CommandsPage 140show arpThe show arp Privileged EXEC mode command displays entries in the ARP table.Syntaxshow arp [ip-address ip-addres

Page 141Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideno ip domain-lookupParametersThis command has no arguments or keywords.Defa

IP Addressing CommandsPage 142ExampleThe following example defines default domain name www.website.com.ip name-serverThe ip name-server Global Configu

Page 143Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault Configuration No host is defined.Command Mode Interface Configurati

IP Addressing CommandsPage 144Parameters•name — Specifies the host entry to be removed. (Range: 1-158 characters)• * — Removes all entries.Default Con

Page 145Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideName/address lookup is enabled Name servers (Preference order): 176.16.1.18

IPv6 Addressing CommandsPage 146Chapter 12.IPv6 Addressing Commandsipv6 enableThe ipv6 enable Interface Configuration mode command enables IPv6 proces

Page 147Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•ipv6-address — The IPv6 network assigned to the interface. The a

IPv6 Addressing CommandsPage 148Command ModeInterface configuration (Ethernet, VLAN, Port-channel). Cannot be configured for a range of interfaces (ra

PrefacePage 14PrefaceThis guide describes how to configure an AT-8000S Series switch with AT-S94 V2.0.0 firmware using the command line interface. The

Page 149Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide–physical-port-name — Designated port number, for example e1.• Configuring

IPv6 Addressing CommandsPage 150ipv6 nd dad attemptsThe ipv6 nd dad attempts Interface Configuration mode command configures the number of consecutive

Page 151Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser Guidelines•Duplicate address detection verifies the uniqueness of new

IPv6 Addressing CommandsPage 152Command ModeGlobal Configuration mode.User Guidelines•The IPv6Z address format: <ipv6-link-local-address>%<in

Page 153Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example configures a static entry in the IPv6 neighbor

IPv6 Addressing CommandsPage 154DELAY_FIRST_PROBE_TIME seconds. If no reachability confirmation is received within DELAY_FIRST_PROBE_TIME seconds of e

Page 155Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 13.Line CommandslineThe line Global Configuration mode command iden

Line CommandsPage 156Default ConfigurationThe default speed is 115200 bps.Command ModeLine Configuration (console) modeUser GuidelinesThis command is

Page 157Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideexec-timeoutThe exec-timeout Line Configuration mode command sets the inter

Line CommandsPage 158User GuidelinesThis command enables the command history function for a specified line. To enable or disable the command history f

Page 15Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide•Chapter 25. "Radius Commands" — Specify the source IP address use

Page 159Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationTh

Line CommandsPage 160ExampleThe following example configures the command history buffer size to 20 commands for the current terminal session.show line

Page 161Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSSH configuration:Interactive timeout: 10 minutes 10 secondsHistory: 10

DHCP Option 82 CommandsPage 162Chapter 14.DHCP Option 82 Commandsip dhcp information optionThe ip dhcp information option Global Configuration mode co

Page 163Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModePrivileged EXECUser GuidelinesThere are no user guidelines for

IP DHCP RelayPage 164Chapter 15.IP DHCP Relayip dhcp relay enable (global)The ip dhcp relay enable Global Configuration command enables Dynamic Host C

Page 165Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeInterface Configuration mode (VLAN, Ethernet, Port-channel)User

IP DHCP RelayPage 166ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModeUs

Page 167Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 16.LACP Commandslacp system-priorityThe lacp system-priority Global

LACP CommandsPage 168lacp port-priorityThe lacp port-priority Interface Configuration (Ethernet) mode command configures physical port priority. Use t

PrefaceContacting Allied TelesisPage 16Contacting Allied TelesisThis section provides Allied Telesis contact information for technical support as well

Page 169Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidelacp timeoutThe lacp timeout Interface Configuration (Ethernet) mode comman

LACP CommandsPage 170show lacp ethernetThe show lacp ethernet Privileged EXEC mode command displays LACP information for Ethernet ports. Syntaxshow la

Page 171Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidedistributing: FALSEexpired: FALSEPartnersystem priority: 0system mac addr:

LACP CommandsPage 172show lacp port-channelThe show lacp port-channel Privileged EXEC mode command displays LACP information for a port-channel.Syntax

Page 173Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide

LLDP CommandsPage 174Chapter 17.LLDP Commandslldp enable (global)The lldp enable Global Configuration mode command enables the Link Layer Discovery Pr

Page 175Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationEnabled in both modes.Command Modes Interface Configur

LLDP CommandsPage 176lldp hold-multiplierThe lldp hold-multiplier Global Configuration mode command specifies the amount of time the receiving device

Page 177Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration mode.User GuidelinesThere are no user guid

LLDP CommandsPage 178Syntaxlldp optional-tlv tlv1 [tlv2 … tlv5]no lldp optional-tlvParameters•tlv — Specifies the TLV that should be included. Availab

Page 17Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 1. Using the CLIOverviewThis chapter describes how to start using th

Page 179Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser Guidelines•Each port can advertise one IP address.• Only static IP add

LLDP CommandsPage 180Syntaxlldp med enable [tlv1 … tlv3]no lldp med enableParameters•tlv — Specifies the TLV that should be included. Available TLVs a

Page 181Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration mode.User Guidelines•Use the lldp med netw

LLDP CommandsPage 182Syntaxlldp med location coordinate datano lldp med location coordinatelldp med location civic-address datano lldp med location ci

Page 183Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser Guidelines There are no user guidelines for this command.ExampleThe fo

LLDP CommandsPage 184The following table describes the significant fields shown in the example:show lldp med configurationThe show lldp med configurat

Page 185Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example displays the Link Layer Discovery Protocol (LL

LLDP CommandsPage 186User GuidelinesThere are no user guidelines for this command.ExampleThe following example displays the Link Layer Discovery Proto

Page 187Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow lldp neighborsThe show lldp neighbors Privileged EXEC mode command dis

LLDP CommandsPage 188ExampleThe following example displays information about neighboring devices discovered using Link Layer Discovery Protocol (LLDP)

Using the CLICLI Command ModesPage 182. Enter the password and press <Enter>. The password is displayed as *. The Privileged EXEC mode prompt is

Page 189Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe following table describes significant LLDP fields:DSCP: 0LLDP-MED Power

LLDP CommandsPage 190Auto-negotiation Advertised CapabilitiesThe speed/duplex/flow-control capabilities of the port that are advertised by the auto-ne

Page 191Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide

Login Banner CommandsPage 192Chapter 18.Login Banner Commandslogin_bannerThe login_banner Privileged EXEC mode command configures the login banner, wh

Page 193Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModePrivileged EXEC mode.User GuidelinesThere are no user guideline

Management ACL CommandsPage 194Chapter 19.Management ACL Commandsmanagement access-listThe management access-list Global Configuration mode command co

Page 195Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example creates a management Access List called mlist,

Management ACL CommandsPage 196User GuidelinesRules with Ethernet, VLAN and port-channel parameters are valid only if an IP address is defined on the

Page 197Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example denies all ports in the Access List called mli

Management ACL CommandsPage 198Command ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following examp

Copyright © 2014 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Page 19Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideInterface Configuration and Specific Configuration ModesInterface Configurat

Page 199Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 20.PHY Diagnostics Commandstest copper-port tdrThe test copper-port

PHY Diagnostics CommandsPage 200Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThe maximum le

Page 201Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example displays the estimated copper cable length att

PHY Diagnostics CommandsPage 2027/e3 CopperTemp – Internally measured transceiver temperature. Voltage - Internally measured supply voltage.Current –

Page 203Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 21.Port Channel Commandsinterface port-channelThe interface port-ch

Port Channel CommandsPage 204Command ModeGlobal Configuration modeUser GuidelinesCommands under the interface range context are executed independently

Page 205Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•port-channel-number — Valid port-channel number.Default Configur

Port Monitor CommandsPage 206Chapter 22.Port Monitor Commandsport monitorThe port monitor Interface Configuration mode command starts a port monitorin

Page 207Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow ports monitorThe show ports monitor User EXEC mode command displays th

Power over Ethernet CommandsPage 208Chapter 23.Power over Ethernet Commandspower inlineThe port inline Interface Configuration (Ethernet) mode command

Using the CLIStarting the CLIPage 20Starting the CLIThe device can be managed over a direct connection to the device console RS-232 port or via a Teln

Page 209Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command Mode

Power over Ethernet CommandsPage 210power inline usage-thresholdThe power inline usage-threshold Global Configuration mode command configures the thre

Page 211Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe fol

Power over Ethernet CommandsPage 212The following table describes the significant fields shown in the example:3/e1 Auto Low Off N/Aconsole# show power

Page 213Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow power inline power-consumptionThe show power inline power-consumption

Power over Ethernet CommandsPage 214Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThere are

Page 215Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 24.QoS CommandsqosThe qos Global Configuration mode command enables

QoS CommandsPage 216User GuidelinesThere are no user guidelines for this command.ExampleThe following example displays QoS attributes when QoS is disa

Page 217Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•rate — Maximum kilobits per second of ingress traffic on a port.

QoS CommandsPage 218show qos interfaceThe show qos interface User EXEC mode command displays interface QoS information.Syntaxshow qos interface [buffe

Page 21Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideTo enter commands that require parameters, enter the required parameters aft

Page 219Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidewrr-queue cos-mapThe wrr-queue cos-map Global Configuration mode command ma

QoS CommandsPage 220qos trust (Global)The qos trust Global Configuration mode command configures the system to basic mode and the trust state. Use the

Page 221Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•dscp-list — Specifies up to 8 DSCP values separated by a space.

QoS CommandsPage 222User GuidelinesIf the port is trusted, the default CoS value of the port is used to assign a CoS value to all untagged packets ent

Page 223Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe following table describes the significant fields shown above.Column Des

Radius CommandsPage 224Chapter 25.Radius Commandsradius-server hostThe radius-server host Global Configuration mode command specifies a RADIUS server

Page 225Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideIf no host-specific timeout, retries, deadtime or key-string values are spe

Radius CommandsPage 226no radius-server retransmitParameters•retries — Specifies the retransmit value. (Range: 1 - 10)Default ConfigurationThe softwar

Page 227Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example configures the source IP address used for comm

Radius CommandsPage 228Default ConfigurationThe timeout value is 3 seconds.Command ModeGlobal Configuration modeUser GuidelinesThere are no user guide

Using the CLIEditing FeaturesPage 22command is entered. If the characters already entered are not enough for the system to identify a single matching

Page 229Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxshow radius-serversParametersThis command has no arguments or keyword

RMON CommandsPage 230Chapter 26.RMON Commandsshow rmon statisticsThe show rmon statistics User EXEC mode command displays RMON Ethernet statistics.Syn

Page 231Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe following table describes significant fields shown above:Field Descript

RMON CommandsPage 232rmon collection historyThe rmon collection history Interface Configuration (Ethernet, port-channel) mode command enables a Remote

Page 233Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command Mode

RMON CommandsPage 234Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThere are no user guideli

Page 235Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe following table describes significant fields shown above:console> sh

RMON CommandsPage 236rmon alarmThe rmon alarm Global Configuration mode command configures alarm conditions. Use the no form of this command to remove

Page 237Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesThere are no user guide

RMON CommandsPage 238The following table describes significant fields shown above:show rmon alarmThe show rmon alarm User EXEC mode command displays a

Copying and Pasting TextUp to 1000 lines of text (i.e., commands) can be copied and pasted into the device.NoteIt is the user’s responsibility to ensu

Page 239Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example displays RMON 1 alarms.The following table des

RMON CommandsPage 240rmon eventThe rmon event Global Configuration mode command configures an event. Use the no form of this command to remove an even

Page 241Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationTh

RMON CommandsPage 242Parameters•event — Specifies the event index. (Range: 0 - 65535)Default ConfigurationThis command has no default configuration.Co

Page 243Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxrmon table-size {history entries | log entries}no rmon table-size {hi

SNMP CommandsPage 244Chapter 27.SNMP Commandssnmp-server communityThe snmp-server community Global Configuration mode command configures the community

Page 245Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe internal security name for SNMPv1 and SNMPv2 security models is mapped

SNMP CommandsPage 246snmp-server groupThe snmp-server group Global Configuration mode command configures a new Simple Management Protocol (SNMP) group

Page 247Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidesnmp-server userThe snmp-server user Global Configuration mode command conf

SNMP CommandsPage 248ExampleThe following example configures an SNMPv3 user John in group user-group.snmp-server engineID localThe snmp-server engineI

ACL CommandsPage 24Chapter 2. ACL Commandsip access-listThe ip access-list Global Configuration mode command defines an IPv4 Access List and places th

Page 249Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidelocal engine ID. The user’s command line password is then destroyed, as req

SNMP CommandsPage 250Syntaxsnmp-server filter filter-name oid-tree {included | excluded}no snmp-server filter filter-name [oid-tree]Parameters•filter-

Page 251Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•ipv4-address — IPv4 address of the host (the targeted recipient)

SNMP CommandsPage 252snmp-server v3-hostThe snmp-server v3-host Global Configuration mode command specifies the recipient of Simple Network Management

Page 253Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example configures an SNMPv3 host.snmp-server trap aut

SNMP CommandsPage 254Command ModeGlobal Configuration modeUser GuidelinesDo not include spaces in the text string or place text that includes spaces i

Page 255Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•variable-name — MIB variable name.• name value — List of name an

SNMP CommandsPage 256ExampleThe following example displays the SNMP communications status.The following table describes significant fields shown above

Page 257Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow snmp engineidThe show snmp engineID Privileged EXEC mode command displ

SNMP CommandsPage 258Command ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example display

Page 25Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidepermit-udp {any | { source source-wildcard}} {any | source-port} {any | {des

Page 259Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe following table describes significant fields shown above.show snmp filt

SNMP CommandsPage 260ExampleThe following example displays the configuration of filters.show snmp usersThe show snmp users Privileged EXEC mode comman

Page 261Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 28.Spanning-Tree Commandsspanning-treeThe spanning-tree Global Conf

Spanning-Tree CommandsPage 262Default ConfigurationSTP is enabled.Command Modes Global Configuration modeUser GuidelinesIn RSTP mode, the device uses

Page 263Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidespanning-tree hello-timeThe spanning-tree hello-time Global Configuration m

Spanning-Tree CommandsPage 264User GuidelinesWhen configuring the maximum age, the following relationships should be kept:2*(Forward-Time - 1) >= M

Page 265Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationSp

Spanning-Tree CommandsPage 266User GuidelinesThe path cost method is configured using the spanning-tree pathcost method Global Configuration mode comm

Page 267Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationPo

Spanning-Tree CommandsPage 268ExampleThe following example enables shared spanning-tree on Ethernet port 1/e5.spanning-tree pathcost methodThe spannin

ACL CommandsPage 26• dscp — Indicates matching the dscp number with the packet dscp value. • ip-precedence — Indicates matching ip-precedence with the

Page 269Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThe default setting is flooding.Command Modes Global C

Spanning-Tree CommandsPage 270spanning-tree bpduguardThe spanning-tree bpduguard Interface Configuration (Ethernet, port-channel) mode command shuts d

Page 271Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand Modes Privileged EXEC modeUser GuidelinesThis feature should be use

Spanning-Tree CommandsPage 272no spanning-tree mst max-hopsParameters•hop-count—Number of hops in an MST region before the BDPU is discarded .(Range:

Page 273Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example configures the port priority of port e1 to 142

Spanning-Tree CommandsPage 274Syntaxspanning-tree mst configurationParametersThis command has no arguments or keywords.Default ConfigurationThis comma

Page 275Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideFor two or more devices to be in the same MST region, they must have the sa

Spanning-Tree CommandsPage 276Parameters•value—Configuration revision number (Range: 0-65535).Default ConfigurationThe default configuration revision

Page 277Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideexit (mst)The exit MST Configuration mode command exits the MST configurati

Spanning-Tree CommandsPage 278Command ModeMST Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following exam

Page 27Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidemobile-registration-request, mobile-registration-reply, domain-name-request,

Page 279Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExamplesThe following examples displays spanning-tree information.console#

Spanning-Tree CommandsPage 280---- ------- -------- ----- --- ---- -------- ----------1/e1 Enabled 128.1 20000 FWD Desg No P2p (RSTP)1/e2 Enabled 128.

Page 281Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideconsole# show spanning-tree activeSpanning tree enabled mode RSTPDefault po

Spanning-Tree CommandsPage 282Name State Prio.Nbr Cost Sts Role PortFast Type---- ------- -------- ----- --- ---- -------- ----------1/e4 Enabled 128.

Page 283Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideNumber of transitions to forwarding state: 1BPDU: sent 2, received 170638Po

Spanning-Tree CommandsPage 284console# show spanning-tree ethernet 1/e1Port 1 (1/e1) enabledState: Forwarding Role: RootPort id: 128.1 Port cost: 200

Page 285Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideName State Prio.Nbr Cost Sts Role PortFast Type---- ------- -------- -----

Spanning-Tree CommandsPage 286Hello Time 2 sec Max Age 20 sec Forward Delay 15 secIST Master ID Priority 32768Address 00:02:4b:29:7a:00This switch is

Page 287Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuidePort 4 (1/e4) enabledState: Forwarding Role: DesignatedPort id: 128.4 Port

Spanning-Tree CommandsPage 288Designated port id: 128.2 Designated cost: 20000Guard Root: Disabled BPDU Guard: DisabledNumber of transitions to forwar

ACL CommandsPage 28Parameters•disable-port — The Ethernet interface is disabled if the condition is matched.• source — Source IP address of the packet

Page 289Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideAddress 00:02:4b:19:7a:00Path Cost 10000Rem hops 19Bridge ID Priority 32768

SSH CommandsPage 290Chapter 29.SSH Commandsip ssh portThe ip ssh port Global Configuration mode command specifies the port to be used by the SSH serve

Page 291Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesIf encryption keys are

SSH CommandsPage 292Syntaxcrypto key generate rsaParametersThis command has no arguments or keywords.Default ConfigurationRSA key pairs do not exist.C

Page 293Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example enables public key authentication for incoming

SSH CommandsPage 294user-keyThe user-key SSH Public Key-string Configuration mode command specifies which SSH public key is manually configured. Use t

Page 295Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationNo keys exist.Command ModeSSH Public Key-string Config

SSH CommandsPage 296ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModePri

Page 297Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command Mode

SSH CommandsPage 298ExampleThe following example displays SSH public keys stored on the device.console# show crypto key pubkey-chain sshUsername Finge

Page 2Table of ContentsPreface...

Page 29Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationNo IPv4 Access List is defined.Command ModeIP Access-li

Page 299Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 30.Syslog Commandslogging onThe logging on Global Configuration mod

Syslog CommandsPage 300Parameters•ipv4-address — Specifies the IPv4 address of the host to be used as a syslog server.• Ipv6-address — Specifies the I

Page 301Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesThere are no user guide

Syslog CommandsPage 302Syntaxlogging buffered size numberno logging buffered sizeParameters•number — Specifies the maximum number of messages stored i

Page 303Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidelogging fileThe logging file Global Configuration mode command limits syslo

Syslog CommandsPage 304ExampleThe following example clears messages from the logging file.aaa loggingThe aaa logging Global Configuration mode command

Page 305Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•copy — Indicates logging messages related to file copy operation

Syslog CommandsPage 306show loggingThe show logging Privileged EXEC mode command displays the state of logging and the syslog messages stored in the i

Page 307Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow logging fileThe show logging file Privileged EXEC mode command display

Syslog CommandsPage 308ExampleThe following example displays the logging state and the syslog messages stored in the logging fileshow syslog-serversTh

ACL CommandsPage 30Default ConfigurationNo IPv6 access list is defined.Command ModeGlobal configurationUser Guidelines•An IPv6 ACL has a unique name.

Page 309Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example displays the settings of the syslog servers.co

TACACS+ CommandsPage 310Chapter 31.TACACS+ Commandstacacs-server hostThe tacacs-server host Global Configuration mode command specifies a TACACS+ host

Page 311Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example specifies a TACACS+ host.tacacs-server keyThe

TACACS+ CommandsPage 312Default Configuration5 secondsCommand ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for this comman

Page 313Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxshow tacacs [ip-address]Parameters•ip-address — Name or IP address of

Tunnel CommandsPage 314Chapter 32.Tunnel Commandsinterface tunnelThe interface tunnel Global Configuration mode command enters tunnel interface config

Page 315Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeInterface Tunnel Configuration mode.User Guidelines•The system

Tunnel CommandsPage 316ExampleThe following example configures a global string Dell_Tunnel_Router to represent a specific automatic tunnel router doma

Page 317Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideno tunnel isatap query-intervalParameters•seconds — Specifies the number of

Tunnel CommandsPage 318ExampleThe following example configures the interval between ISATAP router solicitations messages to 60 seconds.tunnel isatap r

Page 31Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•destination-port — Specifies the UDP/TCP destination port. (Range

Page 319Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default setting.Command ModePrivil

System Management CommandsPage 320Chapter 33.System Management CommandspingThe ping User EXEC mode command sends ICMP echo request packets to another

Page 321Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide–physical-port-name = Product specific.• When using the ping ipv6 command t

System Management CommandsPage 322Parameters•ip-address — IP address of the destination host. An out-of-band IP address can be specified as described

Page 323Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSeveral concurrent Telnet sessions can be opened and switched. To open a su

System Management CommandsPage 324reloadThe reload Privileged EXEC mode command reloads the operating system.SyntaxreloadParametersThis command has no

Page 325Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideresumeSyntaxresume [connection]Default ConfigurationThe default connection

System Management CommandsPage 326ExampleThe following example specifies the device host name.stack masterThe stack master Global Configuration mode c

Page 327Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidestack reloadNoteThis command is operational in the AT-S94/24, AT-S94/24POE,

System Management CommandsPage 328Default ConfigurationThe automatically configured unit number is assigned.Command Modes Global Configuration modeUse

ACL CommandsPage 32User Guidelines•IPv6 Syntax — The 128-bit IPv6 address format is divided into eight groups of four hexadecimal digits. Abbreviation

Page 329Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow usersThe show users User EXEC mode command displays information about

System Management CommandsPage 330ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.C

Page 331Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExample The following example lists open Telnet sessions.The following tabl

System Management CommandsPage 332show system idThe show system id Privileged EXEC mode command displays the system identity information.Syntaxshow sy

Page 333Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•unit unit — Unit number. Default ConfigurationThis command has n

System Management CommandsPage 334ExampleThe following example displays system version information (only for demonstration purposes).console> show

Page 335Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 34.User Interface CommandsdoThe do command executes an EXEC-level c

User Interface CommandsPage 336enableThe enable User EXEC mode command enters the Privileged EXEC mode.Syntaxenable [privilege-level]Parameters•privil

Page 337Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example returns to Users EXEC mode.loginThe login User

User Interface CommandsPage 338Command ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following examp

Page 33Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•destination-port — Specifies the UDP/TCP destination port. (Range

Page 339Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationTh

User Interface CommandsPage 340SyntaxhelpParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configur

Page 341Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeUser EXEC modeUser GuidelinesBy default, a More prompt is displ

User Interface CommandsPage 342show privilegeThe show privilege Privileged/User EXEC mode command displays the current privilege level.Syntaxshow priv

Page 343Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 35.VLAN Commandsvlan databaseThe vlan database Global Configuration

VLAN CommandsPage 344Command ModeVLAN Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example VLAN

Page 345Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideinterface range vlanThe interface range vlan Global Configuration mode comm

VLAN CommandsPage 346Command ModeInterface Configuration (VLAN) mode. Cannot be configured for a range of interfaces (range context).User GuidelinesTh

Page 347Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThis example configures ethernet port 1/e8 as a protected port, so t

VLAN CommandsPage 348switchport access vlanThe switchport access vlan Interface Configuration mode command configures the VLAN ID when the interface i

ACL CommandsPage 34User Guidelines•IPv6 Syntax — The 128-bit IPv6 address format is divided into eight groups of four hexadecimal digits. Abbreviation

Page 349Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeInterface Configuration (Ethernet, port-channel) modeUser Guide

VLAN CommandsPage 350Syntaxswitchport general allowed vlan add vlan-list [tagged | untagged]switchport general allowed vlan remove vlan-listParameters

Page 351Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe fol

VLAN CommandsPage 352Default ConfigurationAll frame types are accepted at ingress.Command ModeInterface Configuration (Ethernet, port-channel) modeUse

Page 353Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example sets a mac-based classification rule.map mac m

VLAN CommandsPage 354ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModePr

Page 355Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example forbids adding VLAN IDs 234 to 256 to Ethernet

VLAN CommandsPage 356show vlanThe show vlan Privileged EXEC mode command displays VLAN information.Syntaxshow vlan [tag vlan-id | name vlan-name ]Para

Page 357Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationTh

VLAN CommandsPage 358ExampleThe following example displays the switchport configuration for Ethernet port 1/e1.console# show interface switchport ethe

Page 35Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example creates a MAC ACL.permit (MAC)The permit MAC-Ac

Page 359Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guide73 outconsole# show interface switchport ethernet 1/e2Port 1/e2:VLAN Member

VLAN CommandsPage 360Acceptable Frame Type: UntaggedGVRP status: Disabled

Page 361Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 36.Web Server Commandsip http serverThe ip http server Global Confi

Web Server CommandsPage 362Command ModeGlobal Configuration modeUser GuidelinesUse the crypto certificate generate Global Configuration mode command t

Page 363Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxip https serverno ip https serverParametersThis command has no argume

Web Server CommandsPage 364ExampleThe following example configures the https port number to 100.ip https exec-timeoutThe ip https exec-timeout Global

Page 365Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•number — Specifies the certificate number. (Range: 1 - 2)• key-g

Web Server CommandsPage 366Syntaxcrypto certificate number request [cn common- name ] [ou organization-unit] [or organization] [loc location] [st stat

Page 367Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example generates and displays a certificate request f

Web Server CommandsPage 368ExampleThe following example imports a certificate signed by Certification Authority for HTTPS.ip https certificate The ip

ACL CommandsPage 36Syntaxdeny [disable-port] {any|{source source- wildcard} {any|{ destination destination- wildcard}} [vlan vlan-id] [cos cos cos-wi

Page 369Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow crypto certificate mycertificateThe show crypto certificate mycertific

Web Server CommandsPage 370ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command

Page 371Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCertificate 1 is activeIssued by: www.verisign.comValid from: 8/9/2004 to 8

802.1x CommandsPage 372Chapter 37. 802.1x Commandsaaa authentication dot1x The aaa authentication dot1x Global Configuration mode command specifies on

Page 373Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideno dot1x system-auth-controlParametersThis command has no arguments or keyw

802.1x CommandsPage 374User GuidelinesIt is recommended to disable spanning tree or to enable spanning-tree PortFast mode on 802.1x edge ports (ports

Page 375Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•seconds — Number of seconds between re-authentication attempts.

802.1x CommandsPage 376dot1x timeout quiet-periodThe dot1x timeout quiet-period Interface Configuration mode command sets the number of seconds that t

Page 377Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationTimeout period is 30 seconds.Command Mode Interface Co

802.1x CommandsPage 378ExampleThe following example sets the number of times that the device sends an EAP-request/identity frame to 6 .dot1x timeout s

Page 37Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxservice-acl input acl-nameno service-acl inputParameters•input — Appli

Page 379Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•seconds — Time in seconds that the device waits for a response f

802.1x CommandsPage 380802.1x is disabledPort Admin Mode Oper Mode Reauth ControlReauth PeriodUsername---- ---------- --------- ------- ------ -------

Page 381Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideThe following table describes significant fields shown above:show dot1x use

802.1x CommandsPage 382Syntaxshow dot1x users [username username]Parameters•username — Supplicant username (Range: 1-160 characters)Default Configurat

Page 383Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow dot1x statisticsThe show dot1x statistics Privileged EXEC mode command

802.1x CommandsPage 384The following table describes the significant fields shown in the display:dot1x auth-not-reqThe dot1x auth-not-req Interface Co

Page 385Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand Mode Interface Configuration (VLAN) modeUser GuidelinesAn access po

802.1x CommandsPage 386ExampleThe following example defines VLAN 2 as a guest VLAN.dot1x single-host-violationThe dot1x single-host-violation Interfac

Page 387Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example forwards frames with source addresses that are

802.1x CommandsPage 388Syntaxshow dot1x advanced interfaceParameters•interface — Ethernet interface.Default ConfigurationThis command has no default c

ACL CommandsPage 38ExampleThe following example displays access lists.show interfaces access-listsThe show interfaces access-lists Privileged EXEC mod

Page 389Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidedot1x guest-vlan enableThe dot1x guest-vlan enable Interface Configuration

802.1x CommandsPage 390Parameters•sec — Specify the timeout in seconds. (Range: 30 – 180)Default ConfigurationThe guest VLAN is applied immediately.Co

Page 391Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideAfter successful authentication the port remains as a member in the unauthe

IndexPage 392IndexAaaa accounting dot1x 47aaa accounting login 46aaa authentication dot1x 372aaa authentication dot1x default 372aaa authentication en

Page 393Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand Completion 21configure 337Contacting Allied Telesis 16copy 85, 93,

IndexPage 394exit (Configuration) 338exit (mst) 277Ffile-system logging 304flowcontrol 104Ggarp timer 119Global Configuration Mode 18gvrp enable (Glob

Page 395Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideip https port 364ip https server 362ip igmp snooping (Global) 125ip igmp sn

IndexPage 396logging console 300logging file 303logging on 299login 337login authentication 41login banner 192Mmanagement access-class 197management a

Page 397Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideqos trust (Global) 221Rradius-server deadtime 228radius-server host 224radi

IndexPage 398show history 341show interfaces advertise 108show interfaces counters 112show interfaces description 111show interfaces port-channel 204s

Page 3 Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideip http authentication ...

Page 39Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 3. AAA Commandsaaa authentication loginThe aaa authentication login

Page 399Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow rmon events 240show rmon history 233show rmon log 241show rmon statist

IndexPage 400sntp authentication-key 74sntp broadcast client enable 77sntp client enable (Interface) 78sntp client poll timer 76sntp server 80sntp tru

Page 401Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideTtacacs-server host 310tacacs-server key 311tacacs-server source-ip 312taca

AAA CommandsPage 40User Guidelines•The default and optional list names created with the aaa authentication login command are used with the login authe

Page 41Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser Guidelines•The default and optiona

AAA CommandsPage 42enable authenticationThe enable authentication Line Configuration mode command specifies the authentication method list when access

Page 43Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThe local user database is checked. This has the same e

AAA CommandsPage 44User GuidelinesThe additional methods of authentication are used only if the previous method returns an error, not if it fails. To

Page 45Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuidepasswordThe password Line Configuration mode command specifies a password on

AAA CommandsPage 46Syntaxusername name [password password] [level level] [encrypted]no username nameParameters•name — The name of the user (Range: 1-

Page 47Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModeGlobal Configuration mode.User Guidelines•This command enables t

AAA CommandsPage 48Parameters•radius — Accounting is performed by a RADIUS server.Default ConfigurationDisabled.Command ModeGlobal Configuration.User

Page 4sntp unicast client enable...7

Page 49Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow users accountsThe show users accounts Privileged EXEC mode command disp

AAA CommandsPage 50no enable password [level level]Parameters•password — Password for this level. (Range: 1-159 characters)• level — Level for which t

Page 51Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleConsole# show accountingLogin: Radius802.1x: Disabled

Address Table CommandsPage 52Chapter 4. Address Table Commandsbridge addressThe bridge address Interface Configuration (VLAN) mode command adds a MAC-

Page 53Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxbridge multicast filteringno bridge multicast filteringParametersThis

Address Table CommandsPage 54Command ModeInterface configuration (VLAN) modeUser Guidelines•If the command is executed without add or remove, the comm

Page 55Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser GuidelinesBefore defining forbidden ports, the Multicast group should b

Address Table CommandsPage 56Syntaxbridge multicast forward-all {add | remove} {ethernet interface-list | port-channel port-channel-number-list}no bri

Page 57Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis setting is disabled.Command ModeInterface Configur

Address Table CommandsPage 58clear bridgeThe clear bridge Privileged EXEC mode command removes any learned entries from the forwarding database.Syntax

Page 5 Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow interfaces counters...

Page 59Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe foll

Address Table CommandsPage 60no port security maxParameters•max-addr— Maximum number of addresses that can be learned by the port. (Range: 1-128)Defau

Page 61Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example adds the MAC-layer address 66:66:66:66:66:66 to

Address Table CommandsPage 62show bridge address-table staticThe show bridge address-table static Privileged EXEC mode command displays statically cre

Page 63Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•vlan — Specifies a valid VLAN, such as VLAN 1.• interface — A val

Address Table CommandsPage 64show bridge multicast address-tableThe show bridge multicast address-table Privileged EXEC mode command displays the brid

Page 65Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExamplesThe following examples display Multicast MAC address and IP Address

Address Table CommandsPage 66NoteA Multicast MAC address maps to multiple IP addresses as shown above.show bridge multicast address-table staticThe sh

Page 67Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxshow bridge multicast filtering vlan-idParameters•vlan-id — VLAN ID va

Address Table CommandsPage 68show bridge multicast unregisteredUse The show bridge multicast unregistered User EXEC mode command displays the unregist

Page 6Chapter 12.IPv6 Addressing Commands... 146ipv6 enable...

Page 69Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines

Address Table CommandsPage 70Default Configuration This command has no default configuration.Command ModePrivileged EXEC modeUser GuidelinesThere are

Page 71Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 5. Clock Commandsclock setThe clock set Privileged EXEC mode command

Clock CommandsPage 72Default ConfigurationNo external clock sourceCommand ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for

Page 73Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideclock summer-timeThe clock summer-time Global Configuration mode command con

Clock CommandsPage 74User GuidelinesIn both the date and recurring forms of the command, the first part of the command specifies when summer time begi

Page 75Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example defines the authentication key for SNTP.sntp au

Clock CommandsPage 76Default ConfigurationNo keys are trusted.Command ModeGlobal Configuration modeUser GuidelinesThe command is relevant for both rec

Page 77Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidesntp broadcast client enableThe sntp broadcast client enable Global Configur

Clock CommandsPage 78User GuidelinesThe sntp client poll timer Global Configuration mode command determines polling time.Use the sntp client enable (I

Page 7 Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guidelldp tx-delay ...

Page 79Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideSyntaxsntp unicast client enableno sntp unicast client enableParametersThis

Clock CommandsPage 80ExampleThe following example enables polling for Simple Network Time Protocol (SNTP) predefined Unicast clients. sntp serverThe s

Page 81Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideExampleThe following example configures the device to accept SNTP traffic fr

Clock CommandsPage 82show sntp configurationThe show sntp configuration Privileged EXEC mode command shows the configuration of the Simple Network Tim

Page 83Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideshow sntp statusThe show sntp status Privileged EXEC mode command shows the

Clock CommandsPage 84176.1.8.179 Unknown 12:17.17.987 PDT Feb 19 2002 8.98 189.19Anycast server:Server Interface Status Last response Offset Delay[mS

Page 85Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 6. Configuration and Image File CommandscopyThe copy Privileged EXEC

Configuration and Image File CommandsPage 86Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Guidel

Page 87Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideCopying a Configuration File from a Server to the Startup ConfigurationTo co

Configuration and Image File CommandsPage 88User GuidelinesThere are no user guidelines for this command.ExampleThe following example displays the lis

Page 8power inline traps enable ...210

Page 89Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeP

Configuration and Image File CommandsPage 90Syntaxshow running-configParametersThis command has no arguments or keywords.Default ConfigurationThis com

Page 91Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeP

Configuration and Image File CommandsPage 92User GuidelinesThere are no user guidelines for this command.ExampleThe following example displays the act

Page 93Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideChapter 7. DHCP Snooping Commandsip dhcp snoopingThe ip dhcp snooping Global

DHCP Snooping CommandsPage 94Command ModeGlobal Configuration modeUser GuidelinesDHCP snooping must be first globally enabled before enabling DHCP sno

Page 95Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s Guideip dhcp snooping information option allowed-untrustedThe ip dhcp snooping in

DHCP Snooping CommandsPage 96User GuidelinesThere are no user guidelines for this command.ExampleThe following example configures the switch to verify

Page 97Allied Telesis AT-8000S-S94-3.0 Command Line Interface User’s GuideParameters•seconds — Specify, in seconds, the update frequency (Range: 600 -

DHCP Snooping CommandsPage 98The entry is displayed in the show commands as a ‘DHCP Snooping entry’.ExampleThe following example configures the DHCP s