Allied Telesis AT-8824 Guía de instalación Pagina 38
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
38 IGMP Enhancements Release Note
Software Version 2.7.5
C613-10454-00 REV A
Example To apply IGMP filter 1 to port 12, use the command:
set swi po=12 igmpfi=1
To limit the number of multicast groups that ports 12–23 can join to 50, use the
command:
set swi po=12-23 igmpma=50
show igmp filter
Syntax SHow IGMP FILter[=filter-id]
where:
■ filter-id is a decimal number in the range 1 to 99.
Description This command displays information about an IGMP filter or all IGMP filters
(Figure 9, Table 12). If a filter is specified, only information about that filter is
displayed.
Figure 9: Example output from the show igmpfilter command
Examples To display information about IGMP filter 3, use the command:
sh igmp fil=3
IGMP Filters
------------------------------------------------------------------
No. Entry Group Address Action Matches
------------------------------------------------------------------
1 - - - -
Received: 230 Passed: 200 Dropped: 30
------------------------------------------------------------------
99 224 224.1.2.3 224.1.2.3 Exclude 10
229 229.1.1.1 229.2.2.2 Include 8
Received: 80 Passed: 70 Dropped: 10
------------------------------------------------------------------
Table 12: Parameters in the output of the show igmp filter command
Parameter Meaning
No. The filter number.
Entry The entry number of an entry in this filter.
Group Address The multicast group address range for this entry.
Action The action to take when the group address of an IGMP
Membership Report matches this entry’s group address.
Matches The number of IGMP Membership Reports matched by this entry.
Received The number of IGMP Membership Reports received on the switch
port that this filter is attached to.
Passed The number of IGMP Membership Reports included and
forwarded to IGMP for processing by this filter.
Dropped The number of IGMP Membership Reports excluded and
discarded by this filter.
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis AT-8824
(179 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales