Allied Telesis AT-8824 Guía de instalación Pagina 184
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-62 set ip route filter Release Note
Software Version 2.7.5
C613-10454-00 REV A
set ip route filter
Syntax SET IP ROUte FILter=filter-id [IP=ipadd] [MASK=ipadd]
[ACtion={INCLude|EXCLude|SWItch}]
[DIrection={RECeive|SENd|BOTH}] [INTerface=interface]
[NEXThop=ipadd] [POLIcy=0..7] [PROTocol={ANY|OSPF|RIP}]
where:
■ filter-id is a number from 1 to 100.
■ ipadd is an IP address in dotted decimal notation.
■ interface is an interface name formed by concatenating a Layer 2 interface
type, an interface instance, and optionally a hyphen followed by a logical
interface number from 0 to 15. If a logical interface is not specified, 0 is
assumed.
Description This command modifies a route filter. A route filter controls which routes are
sent and received by the routing protocols. Route filters do not apply to static
or interface routes.
Parameter Description
FILter The ID number of the filter, in the range 1 to 100.
Default: no default
IP The network address to match. You can use the wildcard character
(”*”) to match a network range. For example, 192.168.*.* matches
all destination networks that start with 192.168. The wildcard
character can only replace a complete number. For example,
192.168.*.* is valid but 192.16*.*.* is not.
Default: no default
MASK The network mask of the network to match. You can use the wildcard
character (”*”) to match a network mask range. For example,
255.255.*.* matches all destination network masks that start with
255.255. The wildcard character can only replace a complete number.
For example, 255.255.*.* is valid but 255.25*.*.* is not.
Default: no default
ACtion What the router or switch does with routes that match the filter.
Default: no default
INCLude The router or switch includes matching routes in its RIB
or the advertisement.
EXCLude The router or switch excludes matching routes from its
RIB or the advertisement.
SWItch The router or switch learns matching routes and adds
them to the special default IP route table in hardware.
The default IP route table can contain up to 16
summary routes.
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis AT-8824
(179 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales