Allied Telesis AT-8824 Guía de instalación Pagina 122
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1-44 show wanlb sessions Release Note
Software Version 2.7.5
C613-10454-00 REV A
show wanlb sessions
Syntax SHow WANLB SEssions [RESource=interface]
Description This command displays information about all of the sessions currently open on
WAN load balancer for a specified resource, or for all resources.
The resource parameter specifies the interface of the resource to display
sessions for. If no resource is specified, all WAN load balancer sessions are
displayed. Valid interfaces are:
■ eth (such as eth0, eth1)
■ PPP (such as ppp0, ppp1)
To see a list of current valid interfaces, use the show interface command.
Figure 1-10: Example output from the show wanlb sessions command
Example To display all the WAN load balancer sessions, use the command:
sh wanlb se
Related Commands show wanlb
WAN Load Balancer Sessions
Resource Source IP Destination IP Prot Expiry
-----------------------------------------------------------
ppp10
192.168.1.1 212.72.1.246 TCP 3599
192.168.1.2 215.73.1.33 UDP 2350
eth0
192.168.1.10 212.72.10.246 TCP 590
192.168.1.20 215.73.10.33 UDP 1250
-----------------------------------------------------------
Table 1-8: Parameters in output of the show wanlb sessions command
Parameter Description
Resource The resource whose sessions are to be displayed.
Source IP The source IP address used for the WAN load balancer session.
Destination IP The destination IP address for the WAN load balancer session.
Protocol The transport protocol used for the WAN load balancer session.
Expiry The number of seconds left before this session expires. Each time the
router receives a packet, the corresponding session is refreshed and
the expiry time is reset. When the time expires, the session is deleted
from the session table.
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis AT-8824
(179 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales