Allied Telesis AT-8824 Guía de instalación Pagina 173
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Filtering IP Routes add ip routemap 2-51
Software Version 2.7.5
C613-10454-00 REV A
Parameters for both
match and set
clauses
Parameters for
match clauses
Parameter Description
ROUTEMap The name of the route map to add the entry or clause to. The
routemap is a character string 0 to 15 characters long. Valid characters
are uppercase and lowercase letters, digits (0-9), and the underscore
character.
Default: no default
ENTry An integer to specify the position of the new entry in the route map.
When a routing protocol uses a route map, it checks the entries in
order, starting with the lowest, until it finds a match. If you leave gaps
between entry numbers, you can add future entries between existing
entries.
Be careful when specifying the entry number. If you make an error in
the number (for example, enter entry=11 instead of entry=1), the
router or switch adds a new entry to the route map.
Default: no default
ACtion Whether matching prefixes or update messages are included or
excluded by the process that is using the route map.
The action parameter applies to the entire entry, but you can change
it at the same time as you add a clause. The most recently entered
value of this parameter applies to the entire entry.
It is not meaningful to have action=exclude in an entry with a set
clause.
Default: the current setting. If there is no current setting, include
Parameter Description
MAtch Adds a match clause to the entry, to determine which routes or BGP
update messages the entry applies to. A route map entry can have
zero or one match clauses. An entry without a match clause matches
all routes or updates.
ASPath The ID number of an AS path list. An update message matches the
route map entry if its AS path attribute matches the AS path list. To
configure an AS path list use the add ip aspathlist command on
page 2-40.
Valid when filtering BGP routes.
Default: no default
COMmunity The ID number of a community list. An update message matches the
route map entry if its community attribute matches the community
list.To configure a community list use the add ip communitylist
command on page 2-42.
Valid when filtering BGP routes.
Default: no default
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis AT-8824
(179 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales