Allied Telesis AT-8824 Guía de instalación Pagina 32
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
32 IGMP Enhancements Release Note
Software Version 2.7.5
C613-10454-00 REV A
Command Reference Updates
This section describes each new command and the changed portions of
modified commands and output screens. For modified commands and output,
new parameters, options and fields are shown in bold.
add igmp filter
Syntax ADD IGMP FILter=filter-id GROupaddress=ipadd[-ipadd]
[ACtion={INCLude|EXCLude}] [ENTry=1..65535]
where:
■ filter-id is a decimal number in the range 1 to 99.
■ ipadd is an IP address in dotted decimal notation.
Description This command adds an entry to an IGMP filter. IGMP filters control a port’s
membership of multicast groups by filtering Membership Reports received
from hosts attached to the port.
The filter must be applied to a switch port using the set switch port command
to take effect.
The filter parameter specifies the number of the filter to add the entry to. The
specified filter must have been created previously using the create igmp filter
command.
The groupaddress parameter specifies an IP multicast group address, or a
range of IP multicast group addresses to match. The IP addresses must be
multicast addresses.
The action parameter specifies the action to take when an IGMP Membership
Report group address matches the value of groupaddress. If you specify
include, Membership Reports matching groupaddress are processed as normal
by IGMP. If you specify exclude, Membership Reports matching groupaddress
are excluding from processing by IGMP, and the packets are discarded. The
default is include.
If an IGMP filter contains at least one entry, then Membership Reports for
group addresses that do not match any entries in the filter are implicitly
excluded and the packets are discarded.
The entry parameter specifies the position of the entry in the filter, and
identifies the entry in the filter. The specified entry number must not already be
used by another entry. If you do not specify an entry number, the entry is
added after the last entry in the filter if there is a free position, or in the last
unused position if the last position is already in use.
Examples To add an entry to filter 6 to accept Membership Reports for multicast group
addresses in the range 229.1.1.2 to 230.1.2.3, use the command:
add igmp fil=6 gro=229.1.1.2-230.1.2.3
To add an entry at position 16 in filter 3 to deny Membership Reports for
multicast group addresses in the range 231.1.1.20 to 231.1.5.3, use the
command:
add igmp fil=3 ent=16 gro=231.1.1.20-231.1.5.3 ac=excl
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis AT-8824
(179 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales