Allied Telesis AT-8824 Guía de instalación Pagina 118
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1-40 show wanlb resource Release Note
Software Version 2.7.5
C613-10454-00 REV A
Table 1-6: Parameters in the detailed output from the show wanlb resource=all
command
Parameter Description
Resource The resource interface.
Status The current state of the interface; on of ENABLED or
DISABLED.
State The current state of the resource; one of UP, DOWN, or
CLOSING. The state of a resource will have the same state
as its associated IP Interface. So if the IP interface is UP, the
resource state will also be UP. If the IP interface is DOWN,
then the resource state will also be DOWN. If the interface
is in the DISABLED state and there are still session active,
then the resource state will be in the CLOSING state.
Weight The weight that the WAN load balancer applies to this
resource when selecting resources for a session. This
parameter is only used and displayed when using the
weighted lottery or weighted least connect algorithms. To
set the WAN load balancer algorithm, use the set wanlb
command on page 1-29.
Weight type How the resource weight was determined; one of Manual,
Automatic, or Perfect Automatic.
Total Sessions The total number of successful sessions that have been
made to this resource while in the UP state.
Current Sessions The total number of sessions currently running on the
resource.
Adaptive Bandwidth
Detection
Bandwidths calculated by adaptive bandwidth detection.
These bandwidths are only displayed when the weight is
determined by the PERFECTAUTOMATIC method.
Current throughput The current throughput (in kbps) for the resource's IP
interface, as calculated by adaptive bandwidth detection.
It is the most most recently calculated value for the
resolution period average.
Current maximum The maximum throughput (in kbps) for the resource's IP
interface, detected by adaptive bandwidth detection for
the current update interval. The maximum throughput is
used to update the resource's weight for the next update
interval.
Healthchecks
Avg overall response The combined average response time from all the
healthcheck host(s).
This figure is displayed when the WAN load balancer uses
the weighted fast response selection method. If
healthchecks are disabled, the response time displayed is
N/A.
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis AT-8824
(179 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales