Allied-telesis AT-S63 Manual de usuario Pagina 242
- Pagina / 464
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 19: MSTP Commands
242
SHOW MSTP
Syntax
show mstp [portconfig=
ports
] [portstate=
ports
] [msti] [cist]
[mstivlanassoc]
Parameters
portconfig Specifies a port. You can specify more than one port at
a time. For a list of the MSTP information displayed by
this parameter, refer to Description below.
portstate Specifies a port. You can specify more than one port at
a time. For a list of the MSTP information displayed by
this parameter, refer to Description below.
msti Displays a list of the MSTIs on the switch and their
associated VLANs. The list does not include the CIST.
cist Displays the CIST priority and the VLANs associated
with CIST.
mstivlanassoc Displays a list of the MSTIs on the switch, including the
CIST, and their associated VLANs.
Note
You can specify only one parameter at a time in this command.
Description
This command displays MSTP parameters. For definitions of the MSTP
terms used below, refer to Chapter 17, “MSTP” in the AT-S63 Management
Software Menus Interface User’s Guide.
Entering SHOW MSTP without any parameters displays the following
MSTP settings:
❑ MSTP status
❑ Force version
❑ Hello time
❑ Forwarding delay
❑ Maximum age
❑ Maximum hops
- Command Line Interface 1
- User’s Guide 1
- Contents 10
- Document Conventions 14
- Contacting Allied Telesyn 16
- Starting a Command Line 19
- Management Session 19
- Command Formatting 22
- Basic Command Line Commands 23
- CLEAR SCREEN 24
- LOGOFF, LOGOUT and QUIT 27
- SAVE CONFIGURATION 29
- SET PROMPT 30
- SET SWITCH CONSOLEMODE 31
- SHOW USER 32
- Basic Switch Commands 33
- DISABLE DHCPBOOTP 35
- DISABLE IP REMOTEASSIGN 36
- DISABLE TELNET 37
- ENABLE DHCPBOOTP 38
- ENABLE IP REMOTEASSIGN 39
- PURGE IP 42
- RESET SWITCH 43
- RESET SYSTEM 44
- RESTART REBOOT 45
- RESTART SWITCH 46
- SET ASYN 48
- SET IP INTERFACE 49
- SET IP ROUTE 51
- SET PASSWORD MANAGER 52
- SET PASSWORD OPERATOR 53
- SET SWITCH CONSOLETIMER 54
- SET SYSTEM 55
- SET USER PASSWORD 56
- SHOW ASYN 57
- SHOW CONFIG 58
- SHOW DHCPBOOTP 59
- SHOW IP ROUTE 61
- SHOW SWITCH 62
- SHOW SYSTEM 63
- SNMPv2 and SNMPv2c 65
- ADD SNMP COMMUNITY 66
- CREATE SNMP COMMUNITY 68
- DELETE SNMP COMMUNITY 71
- DESTROY SNMP COMMUNITY 73
- DISABLE SNMP 74
- DISABLE SNMP AUTHENTICATETRAP 75
- DISABLE SNMP COMMUNITY 76
- ENABLE SNMP 77
- ENABLE SNMP AUTHENTICATETRAP 78
- ENABLE SNMP COMMUNITY 79
- SHOW SNMP 82
- Simple Network Time Protocol 85
- (SNTP) Commands 85
- ADD SNTPSERVER PEER 86
- DISABLE SNTP 88
- ENABLE SNTP 89
- PURGE SNTP 90
- SET DATE 91
- SET SNTP 92
- SET TIME 93
- SHOW SNTP 94
- SHOW TIME 95
- Enhanced Stacking Commands 97
- ACCESS SWITCH 98
- SHOW REMOTELIST 102
- Port Parameter Commands 103
- ACTIVATE SWITCH PORT 104
- DISABLE INTERFACE LINKTRAP 105
- DISABLE SWITCH PORT 106
- DISABLE SWITCH PORT FLOW 107
- ENABLE INTERFACE LINKTRAP 108
- ENABLE SWITCH PORT 109
- ENABLE SWITCH PORT FLOW 110
- RESET SWITCH PORT 111
- SET SWITCH PORT 112
- SET SWITCH PORT RATELIMITING 117
- SHOW INTERFACE 120
- SHOW SWITCH PORT 122
- MAC Address Table Commands 123
- ADD SWITCH FDB 124
- DELETE SWITCH FDB 126
- RESET SWITCH FDB 127
- SHOW SWITCH FDB 129
- Port Trunking Commands 131
- ADD SWITCH TRUNK 132
- CREATE SWITCH TRUNK 133
- DELETE SWITCH TRUNK 135
- DESTROY SWITCH TRUNK 136
- SET SWITCH TRUNK 137
- SHOW SWITCH TRUNK 138
- Port Mirroring Commands 139
- SET SWITCH MIRROR 140
- SET SWITCH PORT MIRROR 141
- SHOW SWITCH MIRROR 143
- File System Commands 145
- CREATE CONFIG 147
- DELETE FILE 148
- SET CONFIG 150
- SHOW FILE 152
- File Download and Upload 153
- Commands 153
- server= 160
- Event Log Commands 163
- DISABLE LOG 164
- ENABLE LOG 165
- PURGE LOG 166
- SAVE LOG 167
- SET LOG FULLACTION 169
- SHOW LOG 170
- AT-S63 module VLAN: 174
- SHOW LOG STATUS 175
- Quality of Service (QoS) 177
- MAP QOS COSP 178
- SET QOS COSP 180
- SET QOS SCHEDULING 181
- SHOW QOS CONFIG 182
- IGMP Snooping Commands 183
- DISABLE IGMPSNOOPING 184
- ENABLE IGMPSNOOPING 185
- SET IP IGMP 186
- SHOW IGMPSNOOPING 188
- SHOW IP IGMP 189
- RRP Snooping Commands 191
- DISABLE RRPSNOOPING 192
- ENABLE RRPSNOOPING 193
- SHOW RRPSNOOPING 194
- STP Commands 195
- ACTIVATE STP 196
- DISABLE STP 197
- ENABLE STP 198
- PURGE STP 199
- Chapter 17: STP Commands 200
- ACTIVATE RSTP 208
- DISABLE RSTP 209
- ENABLE RSTP 210
- PURGE RSTP 211
- SET RSTP 212
- Chapter 18: RSTP Commands 214
- SET RSTP PORT 216
- Chapter 19: MSTP Commands 222
- ADD MSTP 224
- CREATE MSTP 225
- DELETE MSTP 226
- DESTROY MSTP MSTIID 227
- DISABLE MSTP 228
- ENABLE MSTP 229
- PURGE MSTP 230
- SET MSTP 231
- SET MSTP CIST 234
- SET MSTP MSTI 236
- SET MSTP MSTIVLANASSOC 238
- SET MSTP PORT 239
- SHOW MSTP 242
- Chapter 20: SNMPv3 Commands 246
- CLEAR SNMPV3 NOTIFY 252
- CLEAR SNMPV3 TARGETADDR 253
- CLEAR SNMPV3 VIEW 254
- CREATE SNMPV3 ACCESS 255
- CREATE SNMPV3 COMMUNITY 258
- CREATE SNMPV3 GROUP 260
- CREATE SNMPV3 NOTIFY 262
- CREATE SNMPV3 TARGETADDR 264
- CREATE SNMPV3 TARGETPARAMS 266
- CREATE SNMPV3 VIEW 268
- DELETE SNMPV3 USER 270
- DESTROY SNMPv3 ACCESS 271
- DESTROY SNMPv3 GROUP 274
- DESTROY SNMPv3 NOTIFY 275
- DESTROY SNMPv3 TARGETADDR 276
- DESTROY SNMPv3 TARGETPARMS 277
- DESTROY SNMPV3 VIEW 278
- SET SNMPV3 ACCESS 279
- Examples 294
- SHOW SNMPV3 ACCESS 295
- SHOW SNMPV3 COMMUNITY 296
- SHOW SNMPv3 GROUP 297
- SHOW SNMPV3 NOTIFY 298
- SHOW SNMPV3 TARGETADDR 299
- SHOW SNMPV3 TARGETPARAMS 300
- SHOW SNMPV3 USER 301
- SHOW SNMPV3 VIEW 302
- VLANs and Multiple VLAN Mode 303
- ADD VLAN 304
- CREATE VLAN 307
- DELETE VLAN 311
- DESTROY VLAN 314
- SET SWITCH INFILTERING 315
- SET SWITCH MANAGEMENTVLAN 316
- SET SWITCH VLANMODE 317
- SET VLAN 319
- SHOW VLAN 320
- DISABLE GARP 322
- ENABLE GARP 323
- PURGE GARP 324
- SET GARP PORT 325
- SET GARP TIMER 326
- SHOW GARP 328
- SHOW GARP COUNTER 329
- SHOW GARP DATABASE 331
- SHOW GARP GIP 332
- SHOW GARP MACHINE 333
- Protected Ports VLAN Commands 335
- ADD VLAN GROUP 336
- CREATE VLAN PORTPROTECTED 339
- Statistics Commands 345
- RESET SWITCH PORT COUNTER 346
- SHOW SWITCH COUNTER 347
- SHOW SWITCH PORT COUNTER 348
- Port Security Commands 349
- SET SWITCH PORT INTRUSION 350
- SET SWITCH PORT SECURITYMODE 351
- SHOW SWITCH PORT INTRUSION 354
- SHOW SWITCH PORT SECURITYMODE 355
- Management ACL Commands 357
- ADD MGMTACL 358
- DELETE MGMTACL 361
- DISABLE MGMTACL 362
- ENABLE MGMTACL 363
- SET MGMTACL STATE 364
- SHOW MGMTACL 365
- Web Server Commands 367
- DISABLE HTTP SERVER 368
- ENABLE HTTP SERVER 369
- PURGE HTTP SERVER 370
- SET HTTP SERVER 371
- SHOW HTTP SERVER 376
- Encryption Key Commands 377
- CREATE ENCO KEY 378
- DESTROY ENCO KEY 382
- SET ENCO KEY 383
- SHOW ENCO 384
- Chapter 29 385
- Certificate Commands 385
- ADD PKI CERTIFICATE 386
- CREATE PKI CERTIFICATE 388
- CREATE PKI ENROLLMENTREQUEST 391
- DELETE PKI CERTIFICATE 393
- PURGE PKI 394
- SET PKI CERTIFICATE 395
- SET PKI CERTSTORELIMIT 397
- SET SYSTEM DISTINGUISHEDNAME 398
- SHOW PKI 399
- SHOW PKI CERTIFICATE 400
- Secure Sockets Layer (SSL) 401
- ] [maxsessions= 402
- SHOW SSL 403
- Secure Shell (SSH) Commands 405
- DISABLE SSH SERVER 406
- ENABLE SSH SERVER 407
- SET SSH SERVER 410
- SHOW SSH 412
- TACACS+ and RADIUS 413
- ADD RADIUSSERVER 414
- ADD TACACSSERVER 416
- DELETE RADIUSSERVER 417
- DELETE TACACSSERVER 418
- DISABLE AUTHENTICATION 419
- ENABLE AUTHENTICATION 420
- PURGE AUTHENTICATION 421
- SET AUTHENTICATION 422
- SHOW AUTHENTICATION 424
- 802.1x Port-based Network 425
- Access Control Commands 425
- DISABLE PORTACCESS 426
- DISABLE RADIUSACCOUNTING 427
- ENABLE PORTACCESS 428
- ENABLE RADIUSACCOUNTING 429
- SET RADIUSACCOUNTING 436
- SHOW PORTACCESS 438
- SHOW PORTACCESS 439
- SHOW RADIUSACCOUNTING 440
- subnet= 442
- SET DOS IPOPTION 443
- SET DOS LAND 445
- SET DOS PINGOFDEATH 446
- SET DOS SMURF 448
- SET DOS SYNFLOOD 449
- SET DOS TEARDROP 451
- SHOW DOS 453
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S63
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 DEVICE MANAGER Manual de usuario
(118 paginas)
(118 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 VLAN MANAGER Manual de usuario
(56 paginas)
(56 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 INSTALLATION Manual de usuario
(26 paginas)
(26 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 INSTALLATION Manual de usuario
(26 paginas)
(26 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 VLAN MANAGER Manual de usuario
(52 paginas)
(52 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 DEVICE MANAGER Manual de usuario
(127 paginas)
(127 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 DEVICE MANAGEMENT Manual de usuario
(277 paginas)
(277 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales