Allied-telesis AT-FS202SC/FS4 Manual de usuario

AT-FS201 AT-FS202 AT-FS202SC/FS1 AT-FS202SC/FS2 AT-FS202SC/FS3 AT-FS202SC/FS4Fast Ethernet Series SwitchesInstallation GuidePN 613-10761-00 Rev E

Description2Figure 1 illustrates the front panel of an AT-FS20x Series switch.Figure 1 AT-FS20x Series Front Panel (AT-FS202 Model)Figure 2 illustrat

AT-FS20x Series Installation Guide3Table 1 lists the maximum operating distances for the switches.Table 1 Maximum Operating DistancesModel100Base-FX

Description4Key FeaturesThe AT-FS20x switches have the following features:❑ LEDs for unit and port status❑ Auto MDI/MDI-X❑ DIP switches for configurin

AT-FS20x Series Installation Guide5Twisted-Pair PortThe AT-FS20x and AT-FS202SC/FSx Series switches have one 10Base-T/100Base-TX twisted-pair port. Th

Description6The twisted-pair port on the switch can operated in either half- or full-duplex mode. You can set the duplex mode manually or allow the sw

AT-FS20x Series Installation Guide7Switch PerformanceThe AT-FS20x switches have the following performance values:❑ 148,800 pps for 100 Mbps and 14,880

Description8Store and ForwardThe AT-FS20x switches support store and forward switching at Fast Ethernet full-wire speed in 100 Mbps, half- or full-dup

AT-FS20x Series Installation Guide9Figure 4 illustrates a topology using one AT-FS202 switch to interconnect two small networks of stackable hubs.Figu

Description10

11Chapter 2Installing the SwitchThis chapter explains how to install an AT-FS20x and AT-FS202SC/FSx Series switches. These switches can be installed o

Copyright © 2004 Allied Telesyn International, Corp. All rights reserved. No part of this publication may be reproduced without prior written permiss

Installing the Switch12Planning the InstallationBe sure to observe the following guidelines when planning the installation of your switch.❑ The end-no

AT-FS20x Series Installation Guide13NoteSee “Fiber Optic Port Specifications” on page 22 for additional information on the fiber optic port.AT-FS202 5

Installing the Switch14❑ Refer to Table 5 for the cabling specifications for the fiber optic port operating in half-duplex mode.Table 5 100Base-FX Fi

AT-FS20x Series Installation Guide15Installing the SwitchThis section provides a procedure for installing the AT-FS20x switches. When setting the DIP

Installing the Switch16CautionAfter you change the speed or duplex mode of the switch, you must power cycle (shut down and restart) the switch for the

AT-FS20x Series Installation Guide1710. Connect the twisted-pair cable (or cables) to the end node.See Table 7 for information about setting the duple

Installing the Switch18

19Chapter 3TroubleshootingFollow the guidelines below to test and troubleshoot the installation in the event a problem occurs.NoteWhenever the speed a

Troubleshooting20❑ Make sure that the twisted-pair cable does not exceed 100 meters (328 feet) and that you are using a Category 3 or better cable for

21Appendix ATechnical SpecificationsPhysicalDimensions: W x D x H 10.5 cm x 9.5 cm x 2.5 cm (4.12 in x 3.75 in x 1.0 in)Weight: 294 g (10.4 oz)Temper

iiiElectrical Safety and Emission Compliance StatementStandards: This product meets the following standards.RFI Emission EN55022 Class A  1Warning: I

Technical Specifications22Agency CertificationsSafety Conforms to all standards normally supported by Allied Telesyn products including safety standar

AT-FS20x Series Installation Guide23Table 9 Fiber Optic ReceiverTable 10 Fiber Optic DatalinkModelFiber Type11. MMF = Multimode Fiber / SMF = Single

Technical Specifications24Table 11 Fiber Optic Loss Specification (Benchmark)Pinout AssignmentsFigure 5 shows the pin assignments of the RJ-45 connec

AT-FS20x Series Installation Guide25Table 12 lists the 10Base-T/100Base-TX connector pins and their signals when the port is operating in either MDI o

Technical Specifications26

27Appendix BTranslated Safety and Emission InformationImportant: This appendix contains multiple-language translations for the safety statements in th

Translated Safety and Emission Information28Standards: This product meets the following standards. 1RFI Emission EN55022 Class A 2 Warning: In a dom

AT-FS20x Series Installation Guide29USA/Canada Use a UL Listed/CSA Certified AC adapter of DC 12V, 500mA.Europe - EU Use TÜV licensed AC adapter of DC

Translated Safety and Emission Information30Standarder: Dette produkt tilfredsstiller de følgende standarder. 1Radiofrekvens forstyrrelsesemission

AT-FS20x Series Installation Guide31 7 Waarshuwing Klasse-1 laser produkt. 8 Waarchuwing Neit in de straal staren. 9 Dit is een “Klasse 1 LED-produ

Electrical Safety and Emission Compliance StatementivImportant: Appendix B contains translated safety statements for installing this equipment. When y

Translated Safety and Emission Information32 13 Température De Fonctionnement Ce matériel est capable de tolérer une température ambiante maximum de

AT-FS20x Series Installation Guide33Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofrequenza) EN

Translated Safety and Emission Information34 6 Laser EN60825 7Advarsel Laserprodukt av klasse 1. 8Advarsal Stirr ikke på strålen. 9 Dette er et “K

AT-FS20x Series Installation Guide35 13 Temperatura De Funcionamento Este produto foi projetado para uma temperatura ambiente máxima de 40 graus cent

Translated Safety and Emission Information36 5Elsäkerhet TUV-EN60950, UL1950, CSA 950 6 Laser EN60825 7 Varning! Laserprodukt av klass 1. 8 Varnin

vTable of ContentsElectrical Safety and Emission Compliance Statement ...iiiWelcome to Allied Telesyn ...

Table of ContentsviChapter 3Troubleshooting ...19Appendix ATe

viiThis guide contains instructions on how to install the AT-FS20x and AT-FS202SC/FSx Series switches.Where to Find Web-based GuidesThe Allied Telesyn

Welcome to Allied TelesynviiiContacting Allied TelesynThis section provides Allied Telesyn contact information for technical support as well as sales

1Chapter 1DescriptionThe AT-FS20x and AT-FS202SC/FSx Series Switches include the following models:The AT-FS20x Series switches are designed to extend