Allied-telesis AT-S62 Manual de usuario Pagina 140
- Pagina / 420
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 7: SNMPv3 Commands
140
SET SNMPV3 VIEW
Syntax
set snmpv3 view=view [subtree=OID|text] mask=mask
[type=included|excluded]
[storagetype=volatile|nonvolatile]
Parameters
view Specifies the name of the view, up to 32 alphanumeric
characters.
subtree Specifies the view subtree view. Options are:
OID A numeric value in hexadecimal format.
text Text name of the view.
mask Specifies the subtree mask, in hexadecimal format.
type Specifies the view type. Options are:
included Permits the user assign to this View
Name to see the specified subtree.
excluded Does not permit the user assigned to
this View Name to see the specified
subtree.
storagetype Specifies the storage type of this table entry. This is an
optional parameter. The options are:
volatile Does not allow you to save the table
entry to the configuration file on the
switch. This is the default.
nonvolatile Allows you to save the table entry to
the configuration file on the switch.
Description
This command modifies an SNMPv3 View Table entry.
- Command Line 1
- User’s Guide 1
- Table of Contents 3
- Document Conventions 12
- Contacting Allied Telesyn 13
- Starting a Command Line 15
- Management Session 15
- Starting a Management Session 16
- Command Formatting 18
- Basic Command Line Commands 19
- CLEAR SCREEN 20
- LOGOFF, LOGOUT and QUIT 23
- SAVE CONFIGURATION 25
- SET PROMPT 26
- SET SWITCH CONSOLEMODE 27
- SHOW USER 28
- Enhanced Stacking Commands 29
- ACCESS SWITCH 30
- SET SWITCH STACKMODE 32
- SHOW REMOTELIST 34
- Basic Switch Commands 35
- DISABLE DHCPBOOTP 37
- DISABLE IP REMOTEASSIGN 38
- DISABLE TELNET 39
- ENABLE IP REMOTEASSIGN 41
- ENABLE TELNET 42
- PURGE IP 44
- RESET SWITCH 45
- RESET SYSTEM 46
- RESTART REBOOT 47
- RESTART SWITCH 48
- SET ASYN 50
- SET IP INTERFACE 51
- SET IP ROUTE 53
- SET PASSWORD MANAGER 54
- SET PASSWORD OPERATOR 55
- SET SWITCH CONSOLETIMER 56
- SET SYSTEM 57
- SHOW CONFIG 58
- SHOW DHCPBOOTP 59
- SHOW IP ROUTE 61
- SHOW SWITCH 62
- SHOW SYSTEM 63
- Simple Network Time Protocol 64
- (SNTP) Commands 64
- ADD SNTPSERVER PEER 65
- DISABLE SNTP 67
- ENABLE SNTP 68
- PURGE SNTP 69
- SET DATE TIME 70
- SET SNTP 71
- SHOW SNTP 72
- SHOW TIME 73
- SNMPv1 and SNMPv2 Community 74
- Strings and Trap Commands 74
- ADD SNMP COMMUNITY 75
- CREATE SNMP COMMUNITY 77
- DESTROY SNMP COMMUNITY 81
- DISABLE SNMP 82
- DISABLE SNMP AUTHENTICATETRAP 83
- DISABLE SNMP COMMUNITY 84
- ENABLE SNMP 85
- ENABLE SNMP AUTHENTICATETRAP 86
- ENABLE SNMP COMMUNITY 87
- SET SNMP COMMUNITY 88
- SHOW SNMP 90
- SNMPv3 Commands 92
- ADD SNMPV3 USER 94
- CLEAR SNMPV3 ACCESS 96
- CLEAR SNMPV3 COMMUNITY 98
- CLEAR SNMPV3 NOTIFY 99
- CLEAR SNMPV3 TARGETADDR 100
- CLEAR SNMPV3 VIEW 101
- CREATE SNMPV3 ACCESS 102
- Chapter 7: SNMPv3 Commands 104
- DESTROY SNMPv3 ACCESS 118
- DESTROY SNMPv3 COMMUNITY 120
- DESTROY SNMPv3 GROUP 121
- DESTROY SNMPv3 NOTIFY 122
- DESTROY SNMPv3 TARGETADDR 123
- DESTROY SNMPv3 TARGETPARMS 124
- DESTROY SNMPV3 VIEW 125
- SET SNMPV3 ACCESS 126
- SET SNMPV3 COMMUNITY 128
- SET SNMPV3 GROUP 130
- SET SNMPV3 NOTIFY 132
- SET SNMPV3 TARGETADDR 134
- SET SNMPV3 TARGETPARAMS 136
- SET SNMPV3 USER 138
- SET SNMPV3 VIEW 140
- SHOW SNMPV3 ACCESS 142
- SHOW SNMPV3 COMMUNITY 143
- SHOW SNMPv3 GROUP 144
- SHOW SNMPV3 NOTIFY 145
- SHOW SNMPV3 TARGETADDR 146
- SHOW SNMPV3 TARGETPARAMS 147
- SHOW SNMPV3 USER 148
- SHOW SNMPV3 VIEW 149
- Port Parameter Commands 150
- ACTIVATE SWITCH PORT 151
- DISABLE INTERFACE LINKTRAP 152
- DISABLE SWITCH PORT 153
- DISABLE SWITCH PORT FLOW 154
- ENABLE INTERFACE LINKTRAP 155
- ENABLE SWITCH PORT 156
- ENABLE SWITCH PORT FLOW 157
- RESET SWITCH PORT 158
- SET SWITCH PORT 159
- SET SWITCH PORT RATELIMIT 164
- SHOW INTERFACE 167
- SHOW SWITCH PORT 169
- MAC Address Table Commands 170
- ADD SWITCH FDB 171
- DELETE SWITCH FDB 173
- RESET SWITCH FDB 174
- SHOW SWITCH FDB 176
- Port Trunking Commands 178
- ADD SWITCH TRUNK 179
- CREATE SWITCH TRUNK 180
- DELETE SWITCH TRUNK 182
- DESTROY SWITCH TRUNK 183
- SET SWITCH TRUNK 184
- SHOW SWITCH TRUNK 185
- Port Mirroring Commands 186
- SET SWITCH MIRROR 187
- SET SWITCH PORT MIRROR 188
- SHOW SWITCH MIRROR 189
- Statistics Commands 190
- RESET SWITCH PORT COUNTER 191
- SHOW SWITCH COUNTER 192
- SHOW SWITCH PORT COUNTER 193
- File System Commands 194
- CREATE CONFIG 196
- DELETE FILE 197
- SET CONFIG 199
- SHOW FILE 201
- File Download and Upload 202
- Commands 202
- Event Log Commands 212
- DISABLE LOG 213
- ENABLE LOG 214
- PURGE LOG 215
- SAVE LOG 216
- SET LOG FULLACTION 218
- SHOW LOG 219
- SHOW LOG STATUS 224
- Quality of Service (QoS) 225
- MAP QOS COSP 226
- SET QOS SCHEDULING 227
- SHOW QOS CONFIG 228
- IGMP Snooping Commands 229
- DISABLE IGMPSNOOPING 230
- ENABLE IGMPSNOOPING 231
- SET IP IGMP 232
- SHOW IGMPSNOOPING 234
- SHOW IP IGMP 235
- SET DOS IPOPTION 239
- SET DOS LAND 240
- SET DOS PINGOFDEATH 241
- SET DOS SMURF 243
- SET DOS SYNFLOOD 244
- SET DOS TEARDROP 245
- SHOW DOS 247
- STP Commands 249
- ACTIVATE STP 250
- DISABLE STP 251
- ENABLE STP 252
- PURGE STP 253
- Chapter 19: STP Commands 254
- RSTP Commands 260
- ACTIVATE RSTP 261
- DISABLE RSTP 262
- ENABLE RSTP 263
- PURGE RSTP 264
- SET RSTP 265
- Chapter 20: RSTP Commands 266
- SHOW RSTP 272
- MSTP Commands 274
- ACTIVATE MSTP 275
- ADD MSTP 276
- CREATE MSTP 277
- DELETE MSTP 278
- DESTROY MSTP MSTIID 279
- DISABLE MSTP 280
- ENABLE MSTP 281
- PURGE MSTP 282
- SET MSTP 283
- Chapter 21: MSTP Commands 284
- SET MSTP CIST 286
- SET MSTP MSTI 287
- SET MSTP PORT 290
- ADD VLAN 296
- CREATE VLAN 298
- DELETE VLAN 302
- DESTROY VLAN 305
- SET SWITCH INFILTERING 306
- SET SWITCH MANAGEMENTVLAN 307
- SET SWITCH VLANMODE 308
- SET VLAN 310
- SHOW VLAN 311
- DISABLE GARP 313
- ENABLE GARP 314
- PURGE GARP 315
- SET GARP PORT 316
- SET GARP TIMER 317
- SHOW GARP 319
- SHOW GARP COUNTER 320
- SHOW GARP DATABASE 322
- SHOW GARP GIP 323
- SHOW GARP MACHINE 324
- MAC Address Security 325
- SET SWITCH PORT SECURITYMODE 327
- SHOW SWITCH PORT INTRUSION 330
- SHOW SWITCH PORT SECURITYMODE 331
- DISABLE PORTACCESS 333
- DISABLE RADIUSACCOUNTING 334
- ENABLE PORTACCESS 335
- ENABLE RADIUSACCOUNTING 336
- SET RADIUSACCOUNTING 343
- SHOW PORTACCESS 345
- SHOW PORTACCESS 346
- SHOW RADIUSACCOUNTING 347
- Web Server Commands 348
- DISABLE HTTP SERVER 349
- ENABLE HTTP SERVER 350
- PURGE HTTP SERVER 351
- SET HTTP SERVER 352
- SHOW HTTP SERVER 357
- Encryption Key Commands 358
- CREATE ENCO KEY 359
- DESTROY ENCO KEY 363
- SET ENCO KEY 364
- SHOW ENCO 365
- Certificate Commands 366
- ADD PKI CERTIFICATE 367
- CREATE PKI CERTIFICATE 369
- CREATE PKI ENROLLMENTREQUEST 372
- DELETE PKI CERTIFICATE 374
- PURGE PKI 375
- SET PKI CERTIFICATE 376
- SET PKI CERTSTORELIMIT 378
- SET SYSTEM DISTINGUISHEDNAME 379
- SHOW PKI 380
- SHOW PKI CERTIFICATE 381
- Secure Sockets Layer (SSL) 382
- SHOW SSL 384
- Secure Shell (SSH) Commands 385
- DISABLE SSH SERVER 386
- ENABLE SSH SERVER 387
- SET SSH SERVER 390
- SHOW SSH 392
- TACACS+ and RADIUS 393
- ADD RADIUSSERVER 394
- ADD TACACSSERVER 395
- DELETE RADIUSSERVER 396
- DELETE TACACSSERVER 397
- DISABLE AUTHENTICATION 398
- ENABLE AUTHENTICATION 399
- PURGE AUTHENTICATION 400
- SET AUTHENTICATION 401
- SHOW AUTHENTICATION 403
- Management ACL Commands 404
- ADD MGMTACL 405
- DELETE MGMTACL 408
- DISABLE MGMTACL 409
- ENABLE MGMTACL 410
- SET MGMTACL STATE 411
- SHOW MGMTACL 412
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S62
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 DEVICE MANAGER Manual de usuario
(118 paginas)
(118 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 VLAN MANAGER Manual de usuario
(56 paginas)
(56 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 INSTALLATION Manual de usuario
(26 paginas)
(26 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 INSTALLATION Manual de usuario
(26 paginas)
(26 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 VLAN MANAGER Manual de usuario
(52 paginas)
(52 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 DEVICE MANAGER Manual de usuario
(127 paginas)
(127 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales