Allied-telesis AT-MCF2300 Manual de usuario Pagina 185
- Pagina / 190
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-MCF2000 Media Converter Series Installation Guide
185
2. If desired, repeat step 1.
3. If a fiber inspection scope is available, use the scope to inspect the
connector to make sure that it is clean and to check for scratches, pits,
or other problems that may affect performance.
Note
Always keep a dust cap on a fiber optic cable when it is not in use.
Note
Do not touch the end face of the ferrule in the connector.
- Installation Guide 1
- Standards 3
- Translated Safety Statements 4
- Contents 5
- How this Guide is Organized 14
- Contacting Allied Telesis 17
- Features 19
- 20 Section I: Features 20
- Converter Series 21
- Hardware Components 22
- Section I: Features 23 23
- 24 Section I: Features 24
- Section I: Features 25 25
- 26 Section I: Features 26
- AT-MCF2000 and AT-MCF2300 27
- 28 Section I: Features 28
- Section I: Features 29 29
- 30 Section I: Features 30
- AT-MCF2012LC, AT-MCF2012LC/1 31
- Overview 32
- LASER PRODUCT 33
- 12 3 45678 9101112 33
- RDY/FLT HBI HBO 33
- Media Converter Channels 34
- Twisted Pair Ports 35
- ❒ Link Test mode 37
- ❒ MissingLink mode 37
- ❒ Smart MissingLink mode 37
- 38 Section I: Features 38
- MissingLink 39
- Guidelines to 40
- Using the 40
- Operating Modes 40
- Port and Channel LEDs 41
- 42 Section I: Features 42
- Link LED Colors 43
- Link Test Mode 44
- MissingLink Mode 44
- Smart MissingLink Mode 45
- CDC and FDC 46
- Duplex Mode and 46
- Collision LEDs 46
- Section I: Features 47 47
- LT, ML, and 48
- SML Channel 48
- Operating Mode 48
- Section I: Features 49 49
- HBI and HBO 50
- Heartbeat LEDs 50
- Mode Button 51
- 52 Section I: Features 52
- Section I: Features 53 53
- 54 Section I: Features 54
- Section I: Features 57 57
- Front Panel 58
- Section I: Features 59 59
- 60 Section I: Features 60
- RS-232 Terminal Port 61
- Stack Port 62
- Reset Button 63
- 64 Section I: Features 64
- Section I: Features 65 65
- Chassis ID Jumper 66
- General Status 67
- Port LED 68
- 10/100/1000Base 69
- T Management 69
- Port LEDs 69
- 72 Section I: Features 72
- T-MCF2000 74
- Topology 75
- 76 Section I: Features 76
- 78 Section I: Features 78
- Chassis ID Numbers 79
- Section I: Features 81 81
- Chassis ID LEDs 82
- Section I: Features 83 83
- 84 Section I: Features 84
- Installation 85
- 86 Section II: Installation 86
- Chapter 6 87
- 88 Section II: Installation 88
- Section II: Installation 89 89
- 90 Section II: Installation 90
- Selecting a Location 91
- 92 Section II: Installation 92
- Unpacking the AT-MCF2000 or 93
- 94 Section II: Installation 94
- Section II: Installation 95 95
- 96 Section II: Installation 96
- Removing the Rubber Feet 97
- 98 Section II: Installation 98
- Chapter 10 99
- 100 Section II: Installation 100
- Section II: Installation 101 101
- 102 Section II: Installation 102
- Chapter 11 103
- 104 Section II: Installation 104
- Section II: Installation 105 105
- 106 Section II: Installation 106
- Chapter 12 107
- 108 Section II: Installation 108
- Section II: Installation 109 109
- 110 Section II: Installation 110
- Installing the AT-MCF2000M 111
- Management Module 111
- 112 Section II: Installation 112
- -MCF2000M 113
- 114 Section II: Installation 114
- Chapter 14 115
- 116 Section II: Installation 116
- CHASSIS_ID 117
- 118 Section II: Installation 118
- Chapter 15 119
- 120 Section II: Installation 120
- Section II: Installation 121 121
- 122 Section II: Installation 122
- 11mm ±1mm 123
- (0.44in. ±0.03in.) 123
- 124 Section II: Installation 124
- AT-MCF2032SP Module 125
- 126 Section II: Installation 126
- Section II: Installation 127 127
- 128 Section II: Installation 128
- Converter Module 129
- 130 Section II: Installation 130
- Cabling the AT-MCF2000M and 131
- AT-MCF2000S Modules 131
- AT-MCF2000M 132
- Section II: Installation 133 133
- 134 Section II: Installation 134
- Powering on the Chassis 135
- 136 Section II: Installation 136
- Section II: Installation 137 137
- 138 Section II: Installation 138
- Verifying the Installation 139
- 140 Section II: Installation 140
- Converter Modules 141
- AT-MCF2000M Management Module 142
- AT-MCF2000S Stacking Module 142
- ❒ Data bits: 8 143
- ❒ Parity: None 143
- ❒ Stop bits: 1 144
- ❒ Flow control: None 144
- Troubleshooting the Modules 145
- Section II: Installation 147 147
- 148 Section II: Installation 148
- Section II: Installation 149 149
- 150 Section II: Installation 150
- ❒ Replace the module 151
- 152 Section II: Installation 152
- 154 Section II: Installation 154
- 156 Section II: Installation 156
- Replacing the Modules 157
- AT-MCF2012LC 158
- Section II: Installation 159 159
- 160 Section II: Installation 160
- Section II: Installation 161 161
- 162 Section II: Installation 162
- Section II: Installation 163 163
- 164 Section II: Installation 164
- Section II: Installation 165 165
- 166 Section II: Installation 166
- Supply Slot 167
- 168 Section II: Installation 168
- Section II: Installation 169 169
- 170 Section II: Installation 170
- Technical Specifications 171
- AT-MCF2000 Chassis 172
- AT-MCF2300 Chassis 172
- 100Base-FX 175
- Fiber Optic Ports 175
- RS-232 Terminal 177
- Port Pinouts 177
- AT-MCF2KFAN Module 178
- AT-MCF2300FAN Module 178
- DIP Switch Settings for the 179
- Appendix C 181
- PUSH OPENPUSH OPEN 182
- Using a Swab 184
- Numerics 187
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-MCF2300
Hardware De La Computadora Allied-telesis Removable Power Supply and Fan Manual de usuario
(23 paginas)
(23 paginas)
Hardware De La Computadora Allied-telesis x900 Series Switch and SwitchBlade x908 Manual de usuario
(49 paginas)
(49 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales