Allied-telesis AT-S97 Manual de usuario Pagina 20
- Pagina / 254
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 1: Starting a Command Line Management Session
20
Starting a Local Management Session
Note
Local management sessions do not require an IP configuration on
the AT-MCF2000M Management Module.
To start a local management session on the chassis, perform the following
procedure:
1. Connect the DIN-8 connector on the RS-232 Serial Management
Cable included with the AT-MCF2000M Management Module to the
RS-232 Terminal port on the module, as shown in Figure 2.
Figure 2. Connecting the RS-232 Serial Management Cable to the RS-232
Terminal Port
2. Connect the other end of the cable to an RS-232 port on a terminal or
PC with a terminal emulator program.
3. Configure the terminal or terminal emulation program as follows:
Baud rate: 115,200 bps (The RS-232 Terminal port has a baud
rate range of 9600 to 115,200 bps. The default is 115,200 bps. To
adjust the baud rate, refer to “SYSTEM SET ASYNCHRONOUS”
on page 58.)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Note
The port settings are for a DEC VT100 or ANSI terminal, or an
equivalent terminal emulator program.
1261
AT-M CF 2000M
STACK M
A
N
AGE
M
EN
T
TERMIN
AL
10/100/1000BASE-T
RS-232
RESET
SD
R
DY BUSY
M
A
S
T
E
R
POW
E
R
BOOT
RDY
FAULT
1000 LINK
ACT 10/100 LINK ACT
FDX
HDX
COL
LINK ACT
P
ORT
A
C
TIV
IT
Y
0
3
1
ID
AT-MCF2KFAN
N
O
R
M
A
L
F
A
U
L
T
STATUS
- Command Line Interface 1
- User’s Guide 1
- Contents 3
- Document Conventions 12
- Contacting Allied Telesis 14
- Chapter 1 15
- Management Overview 16
- Setting Chassis 18
- ID Numbers 18
- AT-MCF2KFAN 20
- <No System Name> 21
- SNMP Management Session 24
- Quitting a Management Session 25
- Command Formatting 27
- What to Configure First 28
- Assigning an IP 31
- Setting the Date 32
- Enabling the 32
- Telnet or Secure 32
- Shell Server 32
- Saving Your 33
- Stacking 35
- PORT ACTIVITY 37
- Chapter 2: Stacking 38
- Setting Up Stacking 39
- Basic Commands 41
- Question Mark ‘?’ Key 42
- Parameter 46
- IP Configuration Commands 47
- IP DHCP DISABLE 50
- IP DHCP ENABLE 51
- General System Commands 55
- SYSTEM SET ASYNCHRONOUS 58
- SYSTEM SET CHASSIS 59
- SYSTEM SET CLOCK 60
- SYSTEM SET CONSOLE 61
- SYSTEM SET CONTACT 62
- SYSTEM SET HOSTNAME 63
- SYSTEM SET LOCATION 64
- SYSTEM SHOW ASYNCHRONOUS 65
- SYSTEM SHOW CLOCK 66
- SYSTEM SHOW CONSOLE 67
- SYSTEM SHOW INFO 68
- Port and Module Commands 69
- SYSTEM RESET CHASSIS 72
- SYSTEM RESET CLUSTER 74
- SYSTEM RESET MODULE 76
- SYSTEM SET INTERFACE 79
- Mode Select Button 83
- Operating Mode Guidelines 84
- SYSTEM SET INTERFACE PORTNAME 85
- SYSTEM SET MODULE 86
- SYSTEM SET PORT 89
- SYSTEM SHOW CHASSIS 96
- SYSTEM SHOW CLUSTER 99
- SYSTEM SHOW INTERFACE 101
- Privilege Levels 102
- General Description 102
- Examples 107
- SYSTEM SHOW MODULE 108
- Description 109
- Chapter 7 113
- Overview 114
- NTP DISABLE 116
- NTP ENABLE 117
- Parameters 118
- NTP SHOW 119
- Chapter 8 121
- LOGGING CLEAR EVENTLOG 124
- LOGGING DISABLE EVENTLOG 125
- LOGGING DISABLE SYSLOG 126
- LOGGING ENABLE EVENTLOG 127
- LOGGING ENABLE SYSLOG 128
- LOGGING SET EVENTLOG 129
- LOGGING SET SYSLOG 131
- LOGGING SHOW 132
- LOGGING SHOW EVENTLOG 134
- Configuration File Commands 141
- Creating a New 143
- Configuration 143
- Editing a Master 146
- IP Configuration 147
- Log Configuration 148
- NTP Configuration 148
- Telnet and SSH Configuration 149
- User Configuration 149
- Blade Configuration 149
- CONFIG OVERWRITE 154
- CONFIG RUN 155
- CONFIG SAVE 157
- CONFIG SAVE FILESYSTEM 158
- CONFIG SET 160
- CONFIG SHOW 162
- File System Commands 165
- FILE COPY 170
- FILE DELETE 173
- FILE DOWNLOAD 176
- Description of Syntax 1 178
- Description of Syntax 2 179
- Description of Syntax 3 180
- Description of Syntax 4 180
- Software 181
- FILE FASTDOWNLOAD 183
- FILE RENAME 185
- FILE SHOW 188
- FILE UPLOAD 191
- Telnet Server Commands 195
- TELNET DISABLE 198
- TELNET ENABLE 199
- TELNET SHOW 200
- (SNMP) Commands 201
- Default Community Strings 204
- SNMP SET 205
- SNMP SHOW 207
- Chapter 13 209
- SSH DISABLE 212
- SSH ENABLE 213
- SSH SHOW 214
- Manager Account Commands 215
- USER ADD 218
- USER DELETE 220
- USER SET 221
- Adams” account: 222
- USER SHOW 223
- Diagnostics Commands 225
- DIAGNOSTICS SHOW BOOTLOADER 227
- DIAGNOSTICS SHOW CHASSIS 229
- DIAGNOSTICS SHOW MODULE 231
- DIAGNOSTICS SHOW SOFTWARE 234
- AT-S85 and AT-S97 Management 237
- Software Default Settings 237
- Configuration File 238
- Event Log 239
- Manager Account 241
- Master Configuration File 242
- Network Time Protocol Client 243
- RS-232 Terminal Port 244
- Secure Shell Server 245
- Syslog Client 247
- Telnet Server 248
- Numerics 249
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S97
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.10 INSTALLATION Manual de usuario
(29 paginas)
(29 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.10 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.10 VLAN MANAGER Manual de usuario
(71 paginas)
(71 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.10 DEVICE MANAGER Manual de usuario
(133 paginas)
(133 paginas)
Hardware De La Computadora Allied-telesis AT-CM20x Series Converteon Line Cards Manual de usuario
(2 paginas)
(2 paginas)
Hardware De La Computadora Allied-telesis AT-CM212x/1 Series Converteon Line Cards Manual de usuario
(2 paginas)
(2 paginas)
Hardware De La Computadora Allied-telesis AT-CM70S Converteon Line Cards Manual de usuario
(2 paginas)
(2 paginas)
Hardware De La Computadora Allied-telesis AT-CV10x Series Converteon Line Cards Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales