Allied Telesis Rapier 16Fi-FX Guía de instalación Pagina 175
- Pagina / 283
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IP Multicasting set pim interface 81
set pim interface
Syntax SET PIM INTerface=interface[DRPriority=0..4294967295]
[ELectby={DRPriority|IPaddress}]
[HEllointerval={10..15000|DEFault|65535}] [MODe={Dense|
Sparse}] [SRCapable={Yes|No}]
where interface is an interface name formed by concatenating a Layer 2
interface type, an interface instance, and optionally a hyphen followed by a
logical interface number from 0 to 15. If a logical interface is not specified, 0 is
assumed.
Description This command sets parameters for the specified PIM interface. Valid interfaces
are:
■ VLAN (such as vlan1, vlan1-1)
To see a list of current valid interfaces, use the show interface command, or the
show pim interface command. Note that multihomed interfaces must specify
the logical interface number (e.g. ppp1-1).
he drpriority parameter specifies the preference for the switch to become the
designated router (DR) on this interface when electby=drpriority. A higher
value indicates a greater preference. The default is 1.
The electby parameter determines how the switch elects the designated router
for this interface. If drpriority is specified, the interface transmits its drpriority
in its hello messages, which allows DR election by priority. If ipaddress is
specified, the switch does not transmit its DR priority, which causes election by
IP address. The default is drpriority. Note that a switch with
electby=drpriority may still elect by IP address when it does not receive DR
priority in any one of its neighbours’ hello messages. Election by DR priority is
possible only when all routers on the interface supply their DR priority.
The hellointerval parameter specifies the interval at which the switch sends
Hello messages from this interface. Setting the hellointerval parameter to
65535 results in a Hello message being sent with a hold time of 65535, which
means “infinity”. A router receiving this switch’s Hello never expires this
switch as a PIM neighbour. This can be useful on point-to-point links. The
default is 30 seconds.
The mode parameter specifies the PIM operating mode for the interface. The
default is sparse.
Ensure that all interfaces have the same mode setting unless the switch is a
Multicast Border Router.
The srcapable parameter indicates if this interface is able to originate or
process State Refresh messages. The default is no. This parameter applies to
Dense Mode interfaces only.
Examples To set the designated router priority for the interface vlan1 to 100, use the
command:
set pim int=vlan1 drp=100
Related Commands add pim interface
delete pim interface
enable pim
- Software Version 2.9.1 1
- 2 Release Note 2
- Release Licences 5
- Upgrading the GUI File 5
- Backwards Compatibility 6
- Overview of New Features 7
- AT-8624POE Fan Enhancements 9
- C613-10486-00 REV C 10
- VPN Configuration Wizards 11
- Command Changes 12
- System Enhancements 13
- Command Reference Updates 14
- Switching Enhancements 18
- PoE Firmware Upgrade 20
- SHDSL Enhancements 23
- Bridging Enhancements 26
- Software Version 2.9.1 27 27
- Training VLAN VID=2 28
- PPP Link 28
- Software Version 2.9.1 31 31
- Syntax SHow BRIDge 32
- Dynamic DNS Client 33
- Within a Subnet 34
- IP Debug Timeout 35
- Software Version 2.9.1 37 37
- Software Version 2.9.1 41 41
- Syntax SHow DDNS 42
- DHCP Enhancements 45
- DHCP Snooping Enhancements 50
- IP Multicasting Enhancements 55
- OSPF Enhancements 59
- BGP Enhancements 61
- IPv6 Enhancements 63
- ■ all static routes 64
- ■ all interface routes 64
- Firewall Enhancements 65
- Software Version 2.9.1 75 75
- ALG, use the command: 86
- Associations 88
- Changes to Local Commands 94
- IP Multicasting 95
- IP Multicasting 3 97
- IP Multicast Routing 98
- IP Multicasting 5 99
- PIM Dense Mode 100
- Configuring PIM Dense Mode 101
- General PIM-DM 102
- IP Multicasting 9 103
- PIM Sparse Mode 103
- 10 Software Reference 104
- Rendezvous point 105
- IP Multicasting 11 105
- 12 Software Reference 106
- Configuring PIM Sparse Mode 107
- Bootstrap router 108
- General PIM-SM 109
- IP Multicasting 17 111
- Configuring IGMP 112
- Static IGMP 113
- IGMP Proxy 114
- IGMP Snooping 116
- Downstream routers 117
- Fast Leave 118
- Query Solicitation 118
- IP Multicasting 25 119
- IGMP Filtering 120
- IGMP Throttling 122
- IP Multicasting 29 123
- Dynamic MVR 123
- Compatible MVR 123
- Immediate Leave 124
- Configuring MVR 124
- Configuration Examples 125
- Switch B 126
- Switch A 126
- Switch C 126
- Command Reference 134
- IP Multicasting enable pim 69 163
- [interface=vlan] 167
- ■ DVMRP Routers, 224.0.0.4 168
- ■ All PIM routers, 224.0.0.13 168
- ■ IGMP is enabled globally 170
- ■ the interface is active 170
- IP Multicasting set ip mvr 77 171
- 78 set pim Software Reference 172
- Syntax SHow IP IGMP DEBug 191
- Syntax SHow PIM COUnters 197
- Table 11 on page 104) 197
- Syntax SHow PIM INTerface 202
- VLAN (such as vlan1, vlan1-1) 202
- Syntax SHow PIM ROUte 205
- Syntax SHow PIM RPSet 212
- Introduction 217
- Link Layer Discovery Protocol 217
- Type Length Values 218
- Transmission and Reception 219
- Transmission 220
- Reception 220
- Storing LLDP Information 221
- Configuring LLDP 223
- Monitoring LLDP 224
- LLDP Triggers 225
- 802.1AB-2005 251
- LLDP neighbours is displayed 255
- MAC-Forced Forwarding 259
- 2 Software Reference 260
- MAC-Forced 261
- Forwarding with 261
- DHCP snooping 261
- Isolating clients using VLANs 262
- Manually adding 263
- ■ ARP packets 264
- Debugging 265
- Logging 265
- 8 Software Reference 266
- See Also show macff interface 277
- Syntax SHOW MACFF DATABase 278
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis Rapier 16Fi-FX
(44 paginas)
(51 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales