Allied Telesis Rapier 16Fi-FX Guía de instalación Pagina 171
- Pagina / 283
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IP Multicasting set ip mvr 77
set ip mvr
Syntax SET IP MVR VLAN=1..4094 [IMTLeave=port-list]
[MODe={DYnamic|COMpatible}] [RECeiverport=port-list]
[SOurceport=port-list]
where port-list is a port number, a range of port numbers (specified as n-m), or a
comma-separated list of port numbers and/or ranges. Port numbers start at 1
and end at m, where m is the highest numbered Ethernet switch port.
Description This command modifies MVR on a switch.
The vlan parameter specifies the VLAN Identifier with which the multicast
VLAN is associated.
The imtleave parameter specifies the ports on which the Immediate Leave
feature is enabled. If this parameter is specified, the receiver ports immediately
leave the multicast group as soon an IGMP Leave message is received by the
switch on that port. Otherwise, the switch sends an IGMP query on the port
and waits for the IGMP group membership reports when it receives an IGMP
Leave message. If no reports are received within the IGMP timeout period (see
the set ip igmp command on page 75), the receiver port leaves the multicast
group. The port numbers specified must be members of the receiverport list.
The mode parameter specifies the mode of the MVR operation. If dynamic is
specified, IGMP reports are sent out through the source ports of the multicast
VLAN. If compatible is specified, IGMP reports are not sent.
The receiverport parameter specifies a receiver port that receives multicast
data when it is a member of the multicast group. The receiver ports cannot
belong to the multicast VLAN.
The sourceport parameter specifies the uplink (source) ports that send and
receive multicast data to and from the multicast VLAN. All source ports must
belong to a single multicast VLAN.
Examples To modify MVR, use the command:
set ip mvr vlan=22 so=8,9 rec=1-5, 6-8 imtl=2,4
Related Commands create ip mvr
destroy ip mvr
show ip mvr
- Software Version 2.9.1 1
- 2 Release Note 2
- Release Licences 5
- Upgrading the GUI File 5
- Backwards Compatibility 6
- Overview of New Features 7
- AT-8624POE Fan Enhancements 9
- C613-10486-00 REV C 10
- VPN Configuration Wizards 11
- Command Changes 12
- System Enhancements 13
- Command Reference Updates 14
- Switching Enhancements 18
- PoE Firmware Upgrade 20
- SHDSL Enhancements 23
- Bridging Enhancements 26
- Software Version 2.9.1 27 27
- Training VLAN VID=2 28
- PPP Link 28
- Software Version 2.9.1 31 31
- Syntax SHow BRIDge 32
- Dynamic DNS Client 33
- Within a Subnet 34
- IP Debug Timeout 35
- Software Version 2.9.1 37 37
- Software Version 2.9.1 41 41
- Syntax SHow DDNS 42
- DHCP Enhancements 45
- DHCP Snooping Enhancements 50
- IP Multicasting Enhancements 55
- OSPF Enhancements 59
- BGP Enhancements 61
- IPv6 Enhancements 63
- ■ all static routes 64
- ■ all interface routes 64
- Firewall Enhancements 65
- Software Version 2.9.1 75 75
- ALG, use the command: 86
- Associations 88
- Changes to Local Commands 94
- IP Multicasting 95
- IP Multicasting 3 97
- IP Multicast Routing 98
- IP Multicasting 5 99
- PIM Dense Mode 100
- Configuring PIM Dense Mode 101
- General PIM-DM 102
- IP Multicasting 9 103
- PIM Sparse Mode 103
- 10 Software Reference 104
- Rendezvous point 105
- IP Multicasting 11 105
- 12 Software Reference 106
- Configuring PIM Sparse Mode 107
- Bootstrap router 108
- General PIM-SM 109
- IP Multicasting 17 111
- Configuring IGMP 112
- Static IGMP 113
- IGMP Proxy 114
- IGMP Snooping 116
- Downstream routers 117
- Fast Leave 118
- Query Solicitation 118
- IP Multicasting 25 119
- IGMP Filtering 120
- IGMP Throttling 122
- IP Multicasting 29 123
- Dynamic MVR 123
- Compatible MVR 123
- Immediate Leave 124
- Configuring MVR 124
- Configuration Examples 125
- Switch B 126
- Switch A 126
- Switch C 126
- Command Reference 134
- IP Multicasting enable pim 69 163
- [interface=vlan] 167
- ■ DVMRP Routers, 224.0.0.4 168
- ■ All PIM routers, 224.0.0.13 168
- ■ IGMP is enabled globally 170
- ■ the interface is active 170
- IP Multicasting set ip mvr 77 171
- 78 set pim Software Reference 172
- Syntax SHow IP IGMP DEBug 191
- Syntax SHow PIM COUnters 197
- Table 11 on page 104) 197
- Syntax SHow PIM INTerface 202
- VLAN (such as vlan1, vlan1-1) 202
- Syntax SHow PIM ROUte 205
- Syntax SHow PIM RPSet 212
- Introduction 217
- Link Layer Discovery Protocol 217
- Type Length Values 218
- Transmission and Reception 219
- Transmission 220
- Reception 220
- Storing LLDP Information 221
- Configuring LLDP 223
- Monitoring LLDP 224
- LLDP Triggers 225
- 802.1AB-2005 251
- LLDP neighbours is displayed 255
- MAC-Forced Forwarding 259
- 2 Software Reference 260
- MAC-Forced 261
- Forwarding with 261
- DHCP snooping 261
- Isolating clients using VLANs 262
- Manually adding 263
- ■ ARP packets 264
- Debugging 265
- Logging 265
- 8 Software Reference 266
- See Also show macff interface 277
- Syntax SHOW MACFF DATABase 278
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis Rapier 16Fi-FX
(44 paginas)
(51 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales