Allied Telesis Rapier 16Fi-FX Guía de instalación Pagina 102
- Pagina / 283
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8 Software Reference
General PIM-DM
information
The following commands display general PIM-DM information.
PIM-DM timers Timers for PIM-DM operations have defaults that suit most networks and
should not generally be modified.
Caution Changing these timers to inappropriate values can cause PIM to
function in undesirable ways. System administrators should change these timer
values based on a sound understanding of their interaction with other devices
in the network.
If the timers need to be modified, use the command:
set pim [jpinterval={1..65535|default}]
[keepalivetime={10..65535|default}]
[pruneholdtime={1..65535|default}]
[sourcealivetime={10..65535|default}]
[srinterval={10..255|default}] [other-options...]
To list the values of the global PIM timers, use the command:
show pim timer
PIM-DM debugging To display debugging information about PIM-DM, use the command:
enable pim debug={all|assert|bsr|c-rp-adv|graft|hello|joint|
register|staterefresh}[,...]
To see which debugging options are enabled, use the command:
show pim debug
This command... Shows...
show pim config CLI commands that make up the switch’s PIM configuration.
show pim counters the number of PIM messages that the switch has received and
sent, and the number of bad messages it has received.
show pim neighbour information about the neighbouring switches that PIM is aware
of.
show pim route the internal PIM routing table.
show pim staterefresh the internal State Refresh table.
- Software Version 2.9.1 1
- 2 Release Note 2
- Release Licences 5
- Upgrading the GUI File 5
- Backwards Compatibility 6
- Overview of New Features 7
- AT-8624POE Fan Enhancements 9
- C613-10486-00 REV C 10
- VPN Configuration Wizards 11
- Command Changes 12
- System Enhancements 13
- Command Reference Updates 14
- Switching Enhancements 18
- PoE Firmware Upgrade 20
- SHDSL Enhancements 23
- Bridging Enhancements 26
- Software Version 2.9.1 27 27
- Training VLAN VID=2 28
- PPP Link 28
- Software Version 2.9.1 31 31
- Syntax SHow BRIDge 32
- Dynamic DNS Client 33
- Within a Subnet 34
- IP Debug Timeout 35
- Software Version 2.9.1 37 37
- Software Version 2.9.1 41 41
- Syntax SHow DDNS 42
- DHCP Enhancements 45
- DHCP Snooping Enhancements 50
- IP Multicasting Enhancements 55
- OSPF Enhancements 59
- BGP Enhancements 61
- IPv6 Enhancements 63
- ■ all static routes 64
- ■ all interface routes 64
- Firewall Enhancements 65
- Software Version 2.9.1 75 75
- ALG, use the command: 86
- Associations 88
- Changes to Local Commands 94
- IP Multicasting 95
- IP Multicasting 3 97
- IP Multicast Routing 98
- IP Multicasting 5 99
- PIM Dense Mode 100
- Configuring PIM Dense Mode 101
- General PIM-DM 102
- IP Multicasting 9 103
- PIM Sparse Mode 103
- 10 Software Reference 104
- Rendezvous point 105
- IP Multicasting 11 105
- 12 Software Reference 106
- Configuring PIM Sparse Mode 107
- Bootstrap router 108
- General PIM-SM 109
- IP Multicasting 17 111
- Configuring IGMP 112
- Static IGMP 113
- IGMP Proxy 114
- IGMP Snooping 116
- Downstream routers 117
- Fast Leave 118
- Query Solicitation 118
- IP Multicasting 25 119
- IGMP Filtering 120
- IGMP Throttling 122
- IP Multicasting 29 123
- Dynamic MVR 123
- Compatible MVR 123
- Immediate Leave 124
- Configuring MVR 124
- Configuration Examples 125
- Switch B 126
- Switch A 126
- Switch C 126
- Command Reference 134
- IP Multicasting enable pim 69 163
- [interface=vlan] 167
- ■ DVMRP Routers, 224.0.0.4 168
- ■ All PIM routers, 224.0.0.13 168
- ■ IGMP is enabled globally 170
- ■ the interface is active 170
- IP Multicasting set ip mvr 77 171
- 78 set pim Software Reference 172
- Syntax SHow IP IGMP DEBug 191
- Syntax SHow PIM COUnters 197
- Table 11 on page 104) 197
- Syntax SHow PIM INTerface 202
- VLAN (such as vlan1, vlan1-1) 202
- Syntax SHow PIM ROUte 205
- Syntax SHow PIM RPSet 212
- Introduction 217
- Link Layer Discovery Protocol 217
- Type Length Values 218
- Transmission and Reception 219
- Transmission 220
- Reception 220
- Storing LLDP Information 221
- Configuring LLDP 223
- Monitoring LLDP 224
- LLDP Triggers 225
- 802.1AB-2005 251
- LLDP neighbours is displayed 255
- MAC-Forced Forwarding 259
- 2 Software Reference 260
- MAC-Forced 261
- Forwarding with 261
- DHCP snooping 261
- Isolating clients using VLANs 262
- Manually adding 263
- ■ ARP packets 264
- Debugging 265
- Logging 265
- 8 Software Reference 266
- See Also show macff interface 277
- Syntax SHOW MACFF DATABase 278
Relacionado con productos y manuales para Los conmutadores de red Allied Telesis Rapier 16Fi-FX
(44 paginas)
(51 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales