AT-9108, AT-8518, AT-8525, and AT-8550 User’s Command Guide
23
IP OSPF Commands
Command Description
config ospf add virtual-link <routerid>
<areaid>
Adds a virtual link connected to another ABR. Specify the following:
❑
routerid — Far-end router interface number.
❑
areaid — Transit area used for connecting the two end-
points. The transit area cannot have the IP address 0.0.0.0.
config ospf add vlan [<name> | all] Enables OSPF on one or all VLANs (router interfaces). The default
setting is disabled.
config ospf ar
ea <areaid> add
range
<ipaddress> <mask> [advertise | noadvertise]
{type 3 | type 7}
Configures a range of IP addresses in an OSPF area. If advertised, the
range is exported as a single LSA by the ABR.
config ospf ar
ea <areaid> dele
te range
<ipaddress> <mask>
Deletes a range of IP addresses in an OSPF area.
config ospf ar
ea <area_id>
externa
l-filter
[<access_profile> | none]
Configures the router to use the access policy to determine which
external routes are allowed to be exported into the area. This router
must be an ABR.
config ospf ar
ea <area_id>
interare
a-filter
[<access_profile> | none]
Configures the router to use the access policy to determine which
inter-area routes are allowed to be exported into the area. This
router must be an ABR.
config ospf ar
ea <areaid>
normal
Configures an OSFP area as a normal area. The default setting is normal.
config ospf ar
ea <areaid> nssa [summa
ry |
nosummary] stub-default-cost <cost>
{translate}
Configures an OSPF area as a NSSA.
config ospf ar
ea <areaid> stub
[summary |
nosummary] stub-default-cost <cost>
Configures an OSPF area as a stub area.
config ospf asb
r-filter [<ac
cess_policy>
|
none]
Configures a route filter for all the routes OSPF exports from RIP or
other sources.
config ospf [
vlan <
name> | are
a <areaid> |
virt
ual-li
nk <rout
erid> <a
reai
d>]
authe
ntica
tion [
simple-pas
sword
<password>
| md5 <md5_key_id> <md5_key>| none]
Specifies the authentication password (up to eight characters) or
Message Digest 5 (MD5) key for one or all interfaces in an area. The
md5_key is a numeric value with the range 0 to 65,536. When the
OSPF area is specified, authentication information is applied to all
OSPF interfaces within the area.
config ospf [area <areaid> | vlan [<name> |
all]] cost <number>
Configures the cost metric of one or all interface(s). The default cost
is 1.
config ospf delete virtual-link <routerid>
<areaid>
Removes a virtual link.
config ospf delete vlan [<name> | all] Disables OSPF on one or all VLANs (router interfaces).
config ospf [area <areaid> | vlan [<name> |
all]] priority <number>
Configures the priority used in the designated router-election
algorithm for one or all IP interface(s) of for all the interfaces within
the area. The range is 0 through 255, and the default setting is 1.
Setting the value to 0 ensures that the router is never selected as the
designated router or backup designated router.
config ospf routerid [automatic | <routerid>] Configures the OSPF router ID. If automatic is specified, the switch
uses the largest IP interface address as the OSPF router ID. The
default setting is automatic.
(2 paginas)
(34 paginas)
(12 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales