Allied Telesis Switch AT-9000/28 Manual de usuario Pagina 168
- Pagina / 248
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 15: Setting RADIUS and TACACS+ Clients
168
Configuring the Authentication Server
To configure an authentication server, choose from the following
procedures:
“Configuring a TACACS+ Server” on page 168
“Configuring a RADIUS Server” on page 170
Note
Before you can configure an TACACS+ or RADIUS server, you must
select an authentication method. See “Selecting the Authentication
Method” on page 166.
Configuring a
TACACS+
Server
To configure a TACACS+ server, do the following:
1. Select the Security tab.
The Security tab is displayed. See Figure 52 on page 158.
2. From the Security tab, select Authentication Servers.
The Authentication Server Configuration page is displayed. See Figure
55 on page 166.
3. Click the Tacacs+ tab.
The Authentication Server Configuration Page with the Tacacs+ tab is
displayed. See Figure 55 on page 166.
Note
You cannot change the Timeout Value for a TACACS+ server. This
field indicates the number of seconds, that the switch waits for a
response from a TACACS+ server to an authentication request,
before querying the next server in the list.
4. Specify the Key Value setting as needed.
This field defines the value of the global encryption key of the
TACACS+ servers. You can define a global encryption key if you have
one TACACS+ server or if there is more than one server and they all
use the same encryption key. This value is used by the TACACS+
clients. The maximum length is 39 characters. Spaces and special
characters are not permitted.The default value is “ATI.”
- Web Browser 1
- User’s Guide 1
- Copyright 2
- Contents 5
- Document Conventions 12
- Contacting Allied Telesis 14
- Browser Interface 15
- Management Sessions 16
- Web Manager Accounts 17
- Starting a Management Session 19
- Figure 3. Login Page 22
- What to Configure First 27
- Saving Your Changes 28
- 5 on page 28 29
- Basic Switch Parameters 31
- Setting System 33
- Time Manually 33
- Setting An SNTP 35
- Setting a Remote Log Server 40
- Displaying and 43
- Setting the Active 43
- Uploading a 44
- Managing User Accounts 45
- Changing a User 46
- Password 46
- Changing the 48
- User Privilege 48
- Rebooting a Switch 50
- Upgrading the Software 51
- Default Values 53
- Displaying System Information 54
- Setting Port Parameters 57
- Changing the Port Settings 62
- Setting Port Statistics 71
- Displaying Port Statistics 72
- Receive Statistics 73
- Transmit 75
- Statistics 75
- Interface 77
- Clearing Port Statistics 79
- Setting Port Mirroring 81
- Assigning a Destination Port 85
- Chapter 7 89
- Setting the MAC Address 95
- Displaying the MAC Address 96
- Addresses 97
- Assigning a MAC Address 99
- Assigning a 100
- Multicast 100
- Deleting a MAC Address 102
- Setting LACP 105
- Overview 106
- Displaying LACP Trunks 107
- Chapter 9: Setting LACP 108
- Modifying an LACP Trunk 111
- Deleting an LACP Trunk 113
- Adding Static Trunks 119
- Deleting Static Trunks 125
- Chapter 11 127
- Tagged and 129
- Untagged Ports 129
- Displaying VLANs 130
- Adding an VLAN 132
- Modifying VLANs 134
- Deleting VLANs 136
- Chapter 12 137
- Protocol (IGMP) Snooping 145
- Clearing the Routers List 149
- Disabling IGMP Snooping 151
- Displaying the Routers List 152
- Displaying the Hosts List 153
- Security 155
- Chapter 15 163
- Configuring 165
- TACACS+ and 165
- 4. Click Apply 167
- Configuring a 168
- RADIUS Server 170
- Chapter 16 175
- Figure 61 179
- Timeouts 180
- Chapter 17 187
- IP Management 189
- Guidelines 189
- Assigning an IPv4 Address 190
- Assigning an 192
- DHCP IPv4 192
- Assigning an IPv6 Address 194
- Displaying IP Addresses 196
- Deleting IP Addresses 197
- Deleting an IPv6 198
- Setting LLDP and LLDP-MED 199
- Setting LLDP Locations 201
- Figure 69. Locations Tab 202
- Creating a 205
- Coordinate 205
- Location 205
- Creating an 207
- ELIN Location 207
- Configuring LLDP and LLDP-MED 210
- Setting LLDP 212
- Port Assignments 212
- Assigning Port 214
- Locations 214
- Enabling LLDP 216
- Displaying LLDP Statistics 225
- Tab selected 227
- Displaying LLDP Locations 228
- Displaying 229
- Displaying ELIN 230
- Displaying the 232
- Basic LLDP 232
- Configuration 232
- Displaying LLDP 233
- Displaying Port 234
- LLDP-MED TLV 236
- Disabling LLDP on the Switch 238
- Setting sFlow 239
- Enabling sFlow on the Switch 242
- Configuring sFlow on a Port 243
- Chapter 19: Setting sFlow 246
- End of Document 248
Relacionado con productos y manuales para Software Allied Telesis Switch AT-9000/28
Software Allied Telesis AT-WR4500 Manual de usuario
(264 paginas)
(264 paginas)
Software Allied Telesis AT-S94 Guía de usuario
(254 paginas)
(254 paginas)
Software Allied Telesis AT-S94 Manual de usuario
(3 paginas)
(3 paginas)
Software Allied Telesis AT-9000/52 Manual de usuario
(10 paginas)
(10 paginas)
Software Allied Telesis AT-S82 Guía de instalación
(52 paginas)
(52 paginas)
Software Allied Telesis AT-S80 Guía de usuario
(242 paginas)
(242 paginas)
Software Allied Telesis AT-8000S Guía de usuario
(204 paginas)
(204 paginas)
Software Allied Telesis AT-S82 Guía de usuario
(76 paginas)
(76 paginas)
(49 paginas)
Software Allied Telesis AT-S80 Guía de instalación
(44 paginas)
(44 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales