Allied Telesis Switch AT-9000/28 Manual de usuario Pagina 119
- Pagina / 248
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AlliedWare Plus Version 2.1.2 Management Software Web Browser User’s Guide
119
Adding Static Trunks
Review the following information before creating a new static port trunk:
When you create a new trunk, the settings of the lowest numbered port
are copied to the other ports so that all the ports have the same
settings. Therefore, you must examine and verify that the speed,
duplex mode, and flow control settings of the lowest numbered port are
correct for the network device to which the trunk is connected.
All ports of a trunk must be members of the same VLAN.
Ports can be a members of one static port trunk at a time. A port that is
already a member of a trunk cannot be added to another trunk. To
accomplish this, you must remove the member port from its current
trunk assignment first. For instructions, see “Adding Static Trunks” on
page 119.
To create an static port trunk, do the following:
1. Select the Switching tab.
The Switching tab is displayed. See Figure 19 on page 58.
2. From the Switching tab, select Link Aggregation.
For an example of the Link Aggregation selection, see Figure 41 on
page 117.
3. Move the cursor to the right and select Static Trunks.
The Static Trunks page is displayed. See Figure 42 on page 117.
4. From the Static Trunks page, click Add
.
- Web Browser 1
- User’s Guide 1
- Copyright 2
- Contents 5
- Document Conventions 12
- Contacting Allied Telesis 14
- Browser Interface 15
- Management Sessions 16
- Web Manager Accounts 17
- Starting a Management Session 19
- Figure 3. Login Page 22
- What to Configure First 27
- Saving Your Changes 28
- 5 on page 28 29
- Basic Switch Parameters 31
- Setting System 33
- Time Manually 33
- Setting An SNTP 35
- Setting a Remote Log Server 40
- Displaying and 43
- Setting the Active 43
- Uploading a 44
- Managing User Accounts 45
- Changing a User 46
- Password 46
- Changing the 48
- User Privilege 48
- Rebooting a Switch 50
- Upgrading the Software 51
- Default Values 53
- Displaying System Information 54
- Setting Port Parameters 57
- Changing the Port Settings 62
- Setting Port Statistics 71
- Displaying Port Statistics 72
- Receive Statistics 73
- Transmit 75
- Statistics 75
- Interface 77
- Clearing Port Statistics 79
- Setting Port Mirroring 81
- Assigning a Destination Port 85
- Chapter 7 89
- Setting the MAC Address 95
- Displaying the MAC Address 96
- Addresses 97
- Assigning a MAC Address 99
- Assigning a 100
- Multicast 100
- Deleting a MAC Address 102
- Setting LACP 105
- Overview 106
- Displaying LACP Trunks 107
- Chapter 9: Setting LACP 108
- Modifying an LACP Trunk 111
- Deleting an LACP Trunk 113
- Adding Static Trunks 119
- Deleting Static Trunks 125
- Chapter 11 127
- Tagged and 129
- Untagged Ports 129
- Displaying VLANs 130
- Adding an VLAN 132
- Modifying VLANs 134
- Deleting VLANs 136
- Chapter 12 137
- Protocol (IGMP) Snooping 145
- Clearing the Routers List 149
- Disabling IGMP Snooping 151
- Displaying the Routers List 152
- Displaying the Hosts List 153
- Security 155
- Chapter 15 163
- Configuring 165
- TACACS+ and 165
- 4. Click Apply 167
- Configuring a 168
- RADIUS Server 170
- Chapter 16 175
- Figure 61 179
- Timeouts 180
- Chapter 17 187
- IP Management 189
- Guidelines 189
- Assigning an IPv4 Address 190
- Assigning an 192
- DHCP IPv4 192
- Assigning an IPv6 Address 194
- Displaying IP Addresses 196
- Deleting IP Addresses 197
- Deleting an IPv6 198
- Setting LLDP and LLDP-MED 199
- Setting LLDP Locations 201
- Figure 69. Locations Tab 202
- Creating a 205
- Coordinate 205
- Location 205
- Creating an 207
- ELIN Location 207
- Configuring LLDP and LLDP-MED 210
- Setting LLDP 212
- Port Assignments 212
- Assigning Port 214
- Locations 214
- Enabling LLDP 216
- Displaying LLDP Statistics 225
- Tab selected 227
- Displaying LLDP Locations 228
- Displaying 229
- Displaying ELIN 230
- Displaying the 232
- Basic LLDP 232
- Configuration 232
- Displaying LLDP 233
- Displaying Port 234
- LLDP-MED TLV 236
- Disabling LLDP on the Switch 238
- Setting sFlow 239
- Enabling sFlow on the Switch 242
- Configuring sFlow on a Port 243
- Chapter 19: Setting sFlow 246
- End of Document 248
Relacionado con productos y manuales para Software Allied Telesis Switch AT-9000/28
Software Allied Telesis AT-WR4500 Manual de usuario
(264 paginas)
(264 paginas)
Software Allied Telesis AT-S94 Guía de usuario
(254 paginas)
(254 paginas)
Software Allied Telesis AT-S94 Manual de usuario
(3 paginas)
(3 paginas)
Software Allied Telesis AT-9000/52 Manual de usuario
(10 paginas)
(10 paginas)
Software Allied Telesis AT-S82 Guía de instalación
(52 paginas)
(52 paginas)
Software Allied Telesis AT-S80 Guía de usuario
(242 paginas)
(242 paginas)
Software Allied Telesis AT-8000S Guía de usuario
(204 paginas)
(204 paginas)
Software Allied Telesis AT-S82 Guía de usuario
(76 paginas)
(76 paginas)
(49 paginas)
Software Allied Telesis AT-S80 Guía de instalación
(44 paginas)
(44 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales