Allied-telesis x600-48Ts/XP Manual de usuario Pagina 43
- Pagina / 94
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide
43
Table 9. State Change Table
1. The fallback action on a slave is first to run the fallback config script.
Where there is no fallback script, the switch will disable all its switch
ports.
2. The stack member assumes the role of stack master. In specific situations this
condition could result in a stack containing two masters. This would present problems
with network management and the control of links that were previously aggregated.
3. The following situation will apply to a switch that has been removed from the stack by
the using the “no stack enable” command
a. The switch will be unaware of further faults within the stack it was previously a
member of.
b. Should this switch then be powered down, all links previously shutdown (as a
result of running the “no stack enable command”) will remain down.
4. If the slave’s ports are still up, this may cause downstream switches with trunked ports
to operate incorrectly.
Event on Master Node
Reaction on
Master
Reaction on Stack
Member
Reaction on Stack
Member
With Resiliency Link Without Resiliency Link
Both stack links removed No change
Fallback action
1
Re-elect master
2
XEM-STK Removed or Faulty No change
Fallback action
1
Re-elect master
2
Hardware reset (or fault) Reset / offline Re-elect master
Re-elect master
2
Run the no stack enable
command
3
No change
Fallback action
1
Not allowed
Displays Error Message
Software application problem
(lock-up or continual crashes)
Reboot as stack
member
Re-elect master Re-elect master
Software crash or lock-up
Frozen
4
Re-elect master Re-elect master
Power-down or PSU failure Powered down Re-elect master Re-elect master
Event on Stack Member
Node
Reaction on
Master
Reaction on Stack
Member
Reaction on Stack
Member
Both stack links removed No change
Fallback action
1
Re-elect master
2
XEM-STK removed or faulty No change
Fallback action
1
Re-elect master
2
Hardware reset (or fault) No change Reset/offline Reset/offline
Run the no stack enable
command
3
No change
Fallback action
1
Fallback action
1
Software application failover
(lock-up or continual crashes)
No change Re-boot as slave Reboot as stack member
software crash or lock-up No change
Frozen
4
Frozen
4
Power-down / PSU failure No change Powered Down Powered down
- Installation Guide 1
- Product Documentation 4
- Starting a Management Session 5
- Contacting Allied Telesis 8
- Radiated Energy 9
- Industry Canada 9
- Translated Safety Statements 10
- Contents 11
- List of Figures 13
- List of Tables 15
- Overview 17
- Introduction 18
- Switch Descriptions 19
- Connector 20
- AC Power 20
- RPS Connector 22
- Distance 23
- Auto-MDI/ 24
- SFP Transceiver Slots 25
- XFP Transceiver Slots 26
- Redundant Twisted Pair Ports 27
- SD Card Slot 28
- Port LEDs 29
- XFP Transceiver 30
- Slot LEDs 30
- System Status LEDs 31
- Stack LEDs 32
- Terminal Port 34
- AT-LBM (Loop Back) Module 36
- RPS INPUT 36
- 100-240VAC~ 36
- VCS Stacking Module 37
- AT-StackXG 37
- STACK PORT 1 37
- STACK PORT 2 37
- AC Power Connector 38
- Virtual Chassis Stacking 39
- Introduction 40
- uses two switches that are 41
- Recovery States 42
- Resiliency Link 44
- Configurations 44
- Resilient Stacked 45
- Topology 45
- Stack Formation 46
- Selecting the Stack Master 46
- Common Stack Configuration 47
- Stack Management VLAN 47
- Stack Member Identification 48
- Management IP Addresses 49
- Fallback Action 50
- Re-elect New Stack Master 50
- Recombining Separated Stacks 50
- Adding a Stack Member 51
- Replacing a Stack Member 51
- Repairing a Broken Stub 51
- Installing the Hardware 53
- Reviewing Safety Precautions 54
- Unpacking a Switch 56
- 100-240VAC 57
- Resetting the Switch 60
- Installing the 62
- Cabling the Network Ports 65
- Twisted Pair 66
- Specifications 66
- Transceiver 67
- Installing an SFP 68
- SFP Handle 69
- 4741 43 45 70
- 42 44 46 70
- Installing an XFP 71
- Powering on a Switch 74
- Starting a Local 75
- Management 75
- Warranty Registration 76
- Troubleshooting 77
- Power LED is Off 78
- SFP or XFP LED is Off 80
- System Fault LED is Blinking 82
- Chapter 5: Troubleshooting 84
- Technical Specifications 87
- Power Specifications 88
- Certifications 88
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis x600-48Ts/XP
Hardware De La Computadora Allied-telesis AlliedView-EMS 4.0.2 Device-Manager Manual de usuario
(441 paginas)
(441 paginas)
Hardware De La Computadora Allied-telesis AT-9448Ts/XP (Basic Layer 3) Manual de usuario
(108 paginas)
(108 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 4.0.1 INSTALLATION Manual de usuario
(32 paginas)
(32 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 4.0.1 VLAN MANAGER Manual de usuario
(72 paginas)
(72 paginas)
Hardware De La Computadora Allied-telesis AT-9448Ts/XP (Basic Layer 3) Manual de usuario
(106 paginas)
(106 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 4.0.1 QoS MANAGER Manual de usuario
(146 paginas)
(146 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales