Allied-telesis AT-S63 Manual de usuario Pagina 54
- Pagina / 388
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 4: SNMPv1 and SNMPv2c
54 Section I: Basic Features
Enabling or Disabling SNMP Management
To enable or disable SNMP management on the switch, perform the
following procedure:
1. From the Home page, select Configuration.
The System page is displayed with the General tab selected by
default, as shown in Figure 5 on page 40.
2. Select the SNMP tab.
The SNMP tab is shown in Figure 9.
Figure 9. SNMP Tab (Configuration)
3. Click the Enable SNMP Access checkbox to enable or disable SNMP
management. A check in the box indicates that the feature is enabled,
meaning that the switch can be managed from an SNMP
management station. No check indicates that the feature is disabled.
The default is disabled.
4. If you want the switch to send authentication failure traps, click the
Enable Authentication Failure Traps checkbox. A check in the box
indicates that the switch sends the trap.
- Web Browser Interface 1
- User’s Guide 1
- Section II 4
- Section III 6
- Section IV 7
- How This Guide is Organized 15
- Document Conventions 17
- Contacting Allied Telesyn 19
- Management Software Updates 20
- Overview 21
- Management Overview 22
- Local Management Session 24
- Telnet Management Session 25
- Chapter 1: Overview 26
- SNMP Management Session 27
- Management Access Levels 28
- Starting a Web Browser 31
- Management Session 31
- Section I: Basic Features 33 33
- Web Browser Tools 35
- Saving Your Parameter Changes 36
- Section I: Basic Features 37 37
- 38 Section I: Basic Features 38
- Basic Switch Parameters 39
- 40 Section I: Basic Features 40
- 42 Section I: Basic Features 42
- Displaying System Information 44
- Section I: Basic Features 45 45
- Section I: Basic Features 47 47
- Pinging a Remote System 49
- Default Values 50
- Section I: Basic Features 51 51
- SNMPv1 and SNMPv2c 53
- Chapter 4: SNMPv1 and SNMPv2c 54
- 54 Section I: Basic Features 54
- 56 Section I: Basic Features 56
- 58 Section I: Basic Features 58
- 60 Section I: Basic Features 60
- 62 Section I: Basic Features 62
- 64 Section I: Basic Features 64
- Chapter 5: Enhanced Stacking 66
- 66 Section I: Basic Features 66
- 68 Section I: Basic Features 68
- 70 Section I: Basic Features 70
- 72 Section I: Basic Features 72
- Configuring Port Parameters 74
- Section I: Basic Features 75 75
- Section I: Basic Features 77 77
- Section I: Basic Features 79 79
- Chapter 6: Port Parameters 80
- 80 Section I: Basic Features 80
- 82 Section I: Basic Features 82
- 84 Section I: Basic Features 84
- 86 Section I: Basic Features 86
- 88 Section I: Basic Features 88
- Chapter 7: MAC Address Table 90
- 90 Section I: Basic Features 90
- 92 Section I: Basic Features 92
- 94 Section I: Basic Features 94
- 96 Section I: Basic Features 96
- 98 Section I: Basic Features 98
- Creating a Port Trunk 100
- Section I: Basic Features 101 101
- Modifying a Port Trunk 103
- Chapter 8: Port Trunking 104
- 104 Section I: Basic Features 104
- Displaying the Port Trunks 106
- The ports of the trunk 107
- 108 Section I: Basic Features 108
- Creating a Port Mirror 110
- Section I: Basic Features 111 111
- Modifying a Port Mirror 113
- Disabling a Port Mirror 114
- Deleting a Port Mirror 115
- Displaying the Port Mirror 116
- Section I: Basic Features 117 117
- Advanced Features 119
- File Downloads and Uploads 121
- Downloading a File 122
- Uploading a File 125
- Event Log 127
- Chapter 11: Event Log 128
- Displaying Events 130
- Clearing the Event Log 138
- .log file 139
- Configuring CoS 142
- Configuring Egress Scheduling 148
- Displaying the CoS Settings 150
- Displaying the QoS Schedule 152
- IGMP Snooping 153
- Configuring IGMP Snooping 154
- Chapter 13: IGMP Snooping 156
- Chapter 14: STP and RSTP 164
- Configuring STP 166
- Displaying the 170
- STP Settings 170
- Resetting STP to 172
- Settings 172
- 5. Click Defaults 173
- Settings” on page 369 173
- Configuring RSTP 174
- Resetting RSTP 178
- Displaying 178
- RSTP Settings 178
- Enabling MSTP 182
- Configuring MSTP 184
- Chapter 15: MSTP 186
- 6. Click Apply 188
- Creating an 189
- Deleting an 190
- Modifying an 190
- Adding a VLAN 192
- Association 192
- Removing a 192
- Modifying a 193
- Chapter 16: SNMPv3 204
- Deleting a User 210
- Table Entry 210
- User Table 211
- Creating a View 214
- 1.3.6.1.2.1.6 216
- 1.3.6.1.2.1.2.2.1.0.3 216
- Deleting a View 217
- View Table 218
- Access Table 220
- Notify Table 236
- Creating a 238
- Target Address 238
- Modifying 242
- Deleting a 248
- Parameters 248
- Community 252
- Displaying SNMPv3 Tables 258
- Displaying User 259
- Table Entries 259
- Displaying View 261
- SecurityToGroup 263
- 270 Section III: VLANs 270
- Chapter 17: Virtual LANs 272
- 272 Section III: VLANs 272
- 274 Section III: VLANs 274
- Modifying a VLAN 276
- Section III: VLANs 277 277
- Selecting a VLAN Mode 279
- 280 Section III: VLANs 280
- 282 Section III: VLANs 282
- 284 Section III: VLANs 284
- Configuring GVRP 286
- Section III: VLANs 287 287
- Section III: VLANs 289 289
- Leave All Time 290
- Section III: VLANs 291 291
- Section III: VLANs 293 293
- Section III: VLANs 295 295
- Section III: VLANs 297 297
- Section III: VLANs 299 299
- 300 Section III: VLANs 300
- 302 Section III: VLANs 302
- 304 Section IV: Security 304
- Chapter 19: Port Security 306
- 306 Section IV: Security 306
- 308 Section IV: Security 308
- 310 Section IV: Security 310
- 312 Section IV: Security 312
- 314 Section IV: Security 314
- 316 Section IV: Security 316
- Configuring SSH 318
- Section IV: Security 319 319
- Displaying the SSH Settings 320
- Section IV: Security 321 321
- TACACS+ and RADIUS 323
- 324 Section IV: Security 324
- 326 Section IV: Security 326
- 328 Section IV: Security 328
- Section IV: Security 331 331
- 802.1x Port-based Network 333
- Access Control 333
- Setting Port Roles 334
- Section IV: Security 335 335
- Section IV: Security 337 337
- Section IV: Security 339 339
- 340 Section IV: Security 340
- Port Settings 343
- 344 Section IV: Security 344
- RADIUS Accounting 346
- Accounting 347
- 348 Section IV: Security 348
- 350 Section IV: Security 350
- 352 Section IV: Security 352
- 354 Section IV: Security 354
- 356 Section IV: Security 356
- Basic Switch Default Settings 359
- RJ-45 Serial 360
- Terminal Port 360
- Default Settings 360
- SNTP Default 360
- Switch State Slave 362
- SNMP Default Settings 363
- Event Log Default Settings 365
- Quality of Service 366
- VLAN Default Settings 371
- GVRP Default Settings 372
- Web Server Default Settings 375
- SSL Default Settings 376
- PKI Default Settings 377
- SSH Default Settings 378
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S63
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 DEVICE MANAGER Manual de usuario
(118 paginas)
(118 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 VLAN MANAGER Manual de usuario
(56 paginas)
(56 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.1 INSTALLATION Manual de usuario
(26 paginas)
(26 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 INSTALLATION Manual de usuario
(26 paginas)
(26 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 VLAN MANAGER Manual de usuario
(52 paginas)
(52 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 3.0 DEVICE MANAGER Manual de usuario
(127 paginas)
(127 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales