Allied-telesis AT-S83 Manual de usuario Pagina 280
- Pagina / 382
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 14: Routing Information Protocol (RIP) Commands
280
IP RIP AUTHENTICATION STRING
Syntax
ip rip authentication STRING
no ip rip authentication STRING
Parameters
LINE Specifies an authentication string or a password used by a
key. Enter an alphanumeric value.
Description
Use the IP RIP AUTHENTICATION STRING command to define an
authentication string or a password used by a key. Configure any
receiving RIP packet on the interface with the same password.
The software provides the choice of configuring authentication for a single
key or multiple keys at different times. Use this command to specify a
password for a single key on an interface.
Command Mode
Interface mode
Example
The following commands set the authentication string to “Hahaha8” on
interface 4:
switch#configure terminal
switch(config)#interface xe4
switch(config-if)#ip rip authentication “Hahaha8.”
Note
In the above example, configure any receiving RIP packet on
interface 4 with the password “Hahaha8.”
Related Commands
none
- Command Line Interface 1
- User’s Guide 1
- Contents 3
- Contacting Allied Telesis 14
- Interface 15
- Introducing the Command Modes 16
- Commands used to 17
- View Command 20
- Privileged 21
- Executive 21
- Configuration 22
- Terminal Mode 22
- Line Mode 25
- Key Chain Mode 26
- Username:manager 27
- Password: 27
- (none) # 27
- Formatting Commands 28
- Command Line 29
- Conventions 29
- Introduction 31
- Ethernet Technology 32
- Switching 33
- Technology 33
- Routing Protocol 33
- Chapter 2: Introduction 34
- Port Descriptions 36
- Software Features 37
- Standard CLI 38
- MIB support for: 38
- Basic Management Features 39
- Creating User Accounts 40
- SNMP Settings 41
- Assigning an IP Address 43
- View Mode Commands 45
- CLEAR ARP-CACHE 46
- CLEAR IP 47
- CLEAR MAC ADDRESS-TABLE 48
- DEBUG DOT1X 50
- DEBUG MSTP 52
- DEBUG RIP 53
- DEBUG RSTP 54
- DEBUG SNMP 55
- DEBUG STP 56
- Chapter 4: View Mode Commands 58
- SHOW INTERFACE SWITCHPORT 62
- SHOW RUNNING-CONFIG 64
- Chapter 5 67
- BOOT CONFIG-FILE 69
- CONFIGURE TERMINAL 70
- Building configuration 71
- DOWNLOAD A.B.C.D FILE-NAME 73
- DOWNLOAD SERIAL 74
- DOT1X INITIALIZE 75
- SHOW BOOT 77
- SHOW INTERFACE 79
- SHOW INTERFACE STATUS ALL 80
- SHOW NTP ASSOCIATIONS DETAIL 81
- SHOW NTP STATUS 82
- SHOW STATIC-CHANNEL-GROUP 83
- SHOW SYSTEM STATUS 84
- SHOW VERSION 85
- SYSTEM REBOOT 86
- TERMINAL 88
- UNDEBUG DOT1X 90
- UNDEBUG OSPF EVENTS 91
- UNDEBUG OSPF IFSM 92
- UNDEBUG OSPF LSA 93
- UNDEBUG OSPF NFSM 94
- UNDEBUG OSPF NSM 95
- UNDEBUG OSPF PACKET 96
- UNDEBUG OSPF ROUTE 98
- UNDEBUG RIP 99
- UPLOAD A.B.C.D FILE-NAME 100
- UPLOAD SERIAL 101
- Parameters 102
- Description 102
- Command Mode 102
- Examples 102
- Related Commands 104
- Configuration Terminal Mode 105
- Commands 105
- ACCESS-LIST 107
- DEBUG OSPF EVENTS 110
- DEBUG OSPF IFSM 112
- DEBUG OSPF LSA 113
- DEBUG OSPF NFSM 114
- DEBUG OSPF NSM 115
- DEBUG OSPF PACKET 116
- DEBUG OSPF ROUTE 118
- DOT1X SYSTEM-AUTH-CTRL 119
- ENABLE PASSWORD 120
- ENABLE SECRET 121
- FIB RETAIN 123
- HOSTNAME 124
- INTERFACE 125
- IP RADIUS SOURCE-INTERFACE 126
- LINE CONSOLE 127
- LINE VTY 128
- LOG FILE 129
- LOG TRAP 130
- Validation Commands 131
- MAC ADDRESS-TABLE AGEING-TIME 132
- MAXIMUM-PATHS 135
- NTP ACCESS-GROUP 136
- NTP AUTHENTICATE 137
- NTP AUTHENTICATION-KEY 138
- NTP BROADCASTDELAY 139
- NTP MASTER 140
- NTP PEER 141
- NTP SERVER 142
- NTP TRUSTED-KEY 143
- ROUTE-MAP 144
- ROUTER-ID 145
- UNDEBUG ALL 146
- USERNAME 147
- Chapter 7 149
- IP DOMAIN-LIST 150
- IP DOMAIN-LOOKUP 151
- IP DOMAIN-NAME 152
- IP EXTCOMMUNITY-LIST 153
- IP FORWARDING 154
- (SNMP) Commands 155
- SNMP-SERVER COMMUNITY 156
- SNMP-SERVER CONTACT 157
- SNMP-SERVER ENABLE 158
- SNMP-SERVER ENABLE TRAPS SNMP 161
- SNMP-SERVER ENGINEID LOCAL 162
- SNMP-SERVER GROUP 163
- SNMP-SERVER HOST 165
- SNMP-SERVER LOCATION 167
- SNMP-SERVER USER 168
- SNMP-SERVER VIEW 170
- Interface Configuration Mode 171
- ARP-AGEING-TIMEOUT 173
- BANDWIDTH 174
- DESCRIPTION 175
- FLOWCONTROL BACKPRESSURE 176
- FLOWCONTROL RECEIVE 177
- FLOWCONTROL SEND 178
- IP ACCESS-GROUP 179
- IP PROXY-ARP 180
- MAC-ADDRESS 181
- MULTICAST 184
- SHOW CLI 185
- SHUTDOWN 187
- SPANNING-TREE EDGEPORT 188
- SPANNING-TREE FORCE-VERSION 189
- SPANNING-TREE GUARD ROOT 190
- SPANNING-TREE LINK-TYPE 191
- SPANNING-TREE MST INSTANCE 192
- SPANNING-TREE PATH-COST 193
- SPANNING-TREE PORTFAST 194
- SPANNING-TREE PRIORITY 195
- Example 196
- STATIC-CHANNEL-GROUP 198
- STORM-CONTROL 199
- SWITCHPORT ACCESS VLAN 201
- SWITCHPORT MODE ACCESS 202
- SWITCHPORT MODE TRUNK 204
- SWITCHPORT TRUNK ALLOWED VLAN 206
- SWITCHPORT TRUNK NATIVE 208
- IP Interface Commands 209
- IP ADDRESS 211
- Chapter 11 213
- DOT1X MAX-REQ 214
- DOT1X PORT-CONTROL 215
- DOT1X QUIET-PERIOD 216
- DOT1X REAUTHENTICATION 217
- DOT1X REAUTHMAX 218
- DOT1X TIMEOUT RE-AUTHPERIOD 221
- DOT1X TIMEOUT SERVER-TIMEOUT 222
- DOT1X TIMEOUT SUPP-TIMEOUT 223
- DOT1X TIMEOUT TX-PERIOD 224
- RADIUS-SERVER DEADTIME 226
- RADIUS-SERVER HOST 227
- RADIUS-SERVER KEY 228
- RADIUS-SERVER TIMEOUT 230
- SHOW DOT1X 231
- SHOW DOT1X ALL 232
- SHOW DOT1X INTERFACE 235
- Port Configuration 239
- FLOWCONTROL OFF 240
- FLOWCONTROL ON 241
- SHOW FLOWCONTROL INTERFACE 242
- Spanning Tree Protocol (STP) 243
- REGION REGION_NAME 244
- REVISION REVISION_NUMBER 245
- SHOW SPANNING-TREE 246
- SPANNING-TREE ACQUIRE 250
- SPANNING-TREE FORWARD-TIME 253
- SPANNING-TREE HELLO-TIME 254
- SPANNING-TREE MAX-AGE 255
- SPANNING-TREE MAX-HOPS 256
- SPANNING-TREE MODE 257
- SPANNING-TREE MST ENABLE 259
- SPANNING-TREE RSTP ENABLE 267
- SPANNING-TREE STP ENABLE 268
- “TIMERS BASIC” on page 306 270
- “VERSION” on page 308 270
- CLEAR IP RIP ROUTE 271
- DEFAULT-INFORMATION ORIGINATE 273
- DEFAULT-METRIC 274
- DISTANCE 275
- Reference 276
- DISTRIBUTE-LIST 277
- IP RIP AUTHENTICATION MODE 279
- IP RIP AUTHENTICATION STRING 280
- IP RIP RECEIVE-PACKET 281
- IP RIP RECEIVE VERSION 282
- IP RIP SEND-PACKET 283
- IP RIP SEND VERSION 284
- IP RIP SPLIT-HORIZON 285
- KEY CHAIN 287
- MAXIMUM-PREFIX 288
- NEIGHBOR 289
- OFFSET-LIST 291
- PASSIVE-INTERFACE 293
- RECV-BUFFER-SIZE 294
- REDISTRIBUTE CONNECTED 295
- ROUTER RIP 298
- SHOW IP PROTOCOLS RIP 300
- SHOW IP RIP 301
- Equivalent Command 302
- SHOW IP RIP DATABASE 303
- SHOW IP RIP INTERFACE 304
- TIMERS BASIC 306
- AUTO-COST REFERENCE-BANDWIDTH 312
- COMPATIBLE RFC1583 313
- HOST AREA 314
- IP OSPF AUTHENTICATION 316
- IP OSPF AUTHENTICATION-KEY 317
- IP OSPF COST 319
- IP OSPF DATABASE-FILTER 320
- IP OSPF DEAD-INTERVAL 322
- IP OSPF DISABLE ALL 324
- IP OSPF HELLO-INTERVAL 325
- IP OSPF MESSAGE-DIGEST-KEY 326
- IP OSPF MTU 328
- IP OSPF MTU-IGNORE 330
- IP OSPF NETWORK 331
- IP OSPF PRIORITY 332
- IP OSPF RETRANSMIT-INTERVAL 334
- IP OSPF TRANSMIT-DELAY 335
- MAX-CONCURRENT-DD 336
- MAX-UNUSE-PACKET 337
- NETWORK AREA 340
- OSPF ABR-TYPE 342
- OVERFLOW DATABASE 344
- OVERFLOW DATABASE EXTERNAL 346
- REFRESH TIMER 349
- ROUTER OSPF 350
- SUMMARY-ADDRESS 351
- TIMERS SPF 353
- Line Mode Commands 355
- EXEC-TIMEOUT 356
- PRIVILEGE 358
- VLAN Commands 359
- SHOW INTERFACE VLAN 360
- SHOW VLAN 361
- VLAN DATABASE 364
- VLAN NAME 365
- VLAN STATE 366
- Sample Configurations 367
- Configuring VLANs 371
- Numerics 375
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S83
Hardware De La Computadora Allied-telesis SwitchBlade Bandwidth Expander Manual de usuario
(6 paginas)
(6 paginas)
Hardware De La Computadora Allied-telesis SwitchBlade Chassis and Fan Tray Manual de usuario
(11 paginas)
(11 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales