Allied-telesis AT-S102 Manual de usuario Pagina 145
- Pagina / 374
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Converteon Management Software User’s Guide
145
4. To resume managing the chassis, wait twenty to thirty seconds for the
standby card to transition to the active state and, afterwards, start a
new management session.
Note
For explanations of the other two selections in the Management
Card Redundancy menu, refer to “Saving Your Configuration
Changes” on page 78.
Web Browser To activate the standby management card from the web browser windows:
1. Select Management Card Redundancy from the menu bar to display
the tab in Figure 50.
Figure 50. Management Card Redundancy Tab
2. In the section Switch Over Management Cards, click Select. A
confirmation prompt is displayed.
3. In the confirmation prompt, click Yes and Apply to activate the
standby card or No and Apply to cancel the procedure. If you select
Yes, your management session ends as the active and standby
management cards change states.
4. To resume managing the chassis, wait twenty to thirty seconds for the
standby card to transition to the active state and afterwards start a new
management session.
Note
The two other selections in the Management Card Redundancy tab
are described in “Saving Your Configuration Changes” on page 78.
- User’s Guide 1
- Contents 3
- Product Name Conventions 17
- Contacting Allied Telesis 18
- Management 19
- Software Updates 19
- AT-CV5M02 Management Card 21
- Features 22
- AT-S99 Management Software 23
- Console Port 23
- 10/100Base-TX Port 23
- IP Address Configuration 23
- Event Log 24
- Activity Monitor 24
- Syslog Client 24
- Network Time Protocol Client 24
- Manager and Operator Accounts 25
- Management Access 26
- Accessing Your Network 31
- Configuration Files 32
- Restoring 33
- Configurations to 33
- AT-CM Line 35
- Cards and 35
- Remote Peer 35
- Active and 36
- Converteon Chassis 38
- Management Software 46
- Maximum Frame Sizes 46
- Low Power Mode 46
- Packet Rate Limiting 47
- Operating Modes 48
- MissingLink and 51
- OAM Visible 51
- MissingLink 52
- Setting the 54
- Operating Mode 54
- OAM-based Features 55
- Remote Peer Management 56
- Chapter 3: OAM-based Features 58
- AT-CM2 Line Cards 65
- AT-CM3 Line Cards 66
- OAM Variable Requests 68
- OAM Client Settings 69
- Starting a Management Session 71
- AT-CV501 72
- > Enable this port 74
- Disable this port 74
- System name: -> 74
- Figure 14. Chassis View 77
- Configuration of 78
- System Configuration Menu 79
- Save System Configuration 79
- Return to Main Menu 79
- Configurations of 80
- Switch Over Management Cards 83
- Changing the 85
- Manager and 85
- Operator 85
- Passwords 85
- Setting the Date 87
- Naming the 88
- Saving Your 89
- Configuring the 93
- OAM Settings 93
- Testing the OAM 95
- Configuring the AT-CV5M02 99
- Management Card 99
- Assigning a Name 104
- System Configuration option 105
- Web Server Configuration Menu 114
- Disable Web Server 114
- > Enable Web Server 114
- Resetting the Management Card 119
- Viewing the Event Log 122
- Viewing the Activity Monitor 130
- Configuring the Syslog Client 131
- Converteon 142
- Terminal Configuration Menu 146
- Data Rate (baud rate) 146
- Pinging Network Devices 152
- Chapter 6 157
- Figure 60. Menu View 165
- Port Management Menu 170
- Module 4 - Port A 170
- Port Configurations 170
- OAM Configurations 170
- Setting the Operating Mode 176
- Max Frame Size Config Menu 182
- Module 14 182
- Max Frame Size: 1632 182
- Setting the Auto-copy Feature 183
- Auto-copy Enable 184
- > Auto-copy Disable 184
- Resetting an AT-CM3 Line Card 198
- Converter Line Cards 199
- Line Cards 201
- Displaying Port Statistics 203
- Chapter 7 217
- Displaying the 218
- Status of the 218
- Remote Line 218
- Restoring the 225
- Default Settings 225
- Last Saved 226
- Configuration 226
- Parameter 232
- Settings 232
- Resetting the 234
- Remote AT-CM3 234
- AT-CM Line Cards 238
- Chapter 8 241
- AT-CV5000 243
- TDM Management Menu 244
- Module 15, Port C 244
- TDM Port Configurations 244
- UART Configurations 244
- UART Configuration Menu 245
- > UART Local Console Mode 245
- UART Back Plane Mode 245
- Configuring the Operations 253
- Configuring the OAM Client 254
- OAM port is disconnected 260
- OAM is not in active mode 260
- Displaying OAM Statistics 273
- Configuring SNMPv3 279
- SNMPv3 Overview 280
- SNMPv3 Storage 283
- SNMPv3 Message 283
- Notification 283
- SNMPV3 Auth Table 284
- SNMPv3 User Table 284
- SNMPv3 View Table 284
- SNMPv3 Access Table 284
- SNMPv3 Group Table 287
- SNMPv3 Notify Table 287
- SNMPv3 Target Address Table 287
- Configuring SNMPv3 Entities 289
- Chapter 11 315
- Overview 316
- Programs 317
- Saving the 329
- Configuring the TFTP Client 330
- Card and the Line Cards 337
- SNMPv3 Configuration Examples 345
- SNMPv3 Manager Configuration 346
- SNMPv3 Operator Configuration 348
- SNMPv3 Worksheet 349
- Line Card 351
- Numerics 371
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S102
Hardware De La Computadora Allied-telesis AT-9448Ts/XP (Basic Layer 3) Manual de usuario
(84 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 MIB COMPILER Manual de usuario
(13 paginas)
(13 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 INSTALLATION Manual de usuario
(29 paginas)
(29 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales