Allied-telesis AT-S100 Manual de usuario Pagina 254
- Pagina / 274
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 10: Spanning Tree Protocol (STP) Commands
254 Section II: Advanced Configuration
SPANNING-TREE PORTFAST BPDU-GUARD DEFAULT
Syntax
spanning-tree portfast bpdu-guard default
no spanning-tree portfast bpdu-guard default
Parameters
none
Description
Use the SPANNING-TREE BPDU-GUARD DEFAULT command to enable
the BPDU (Bridge Protocol Data Unit) guard feature on a bridge. This
command indicates the bridge level BPDU-Guard configuration takes
effect.
When the BPDU guard feature is set for a bridge, all portfast-enabled
interfaces of the bridge that have the BPDU guard set to default shut down
the interface on receiving a BPDU. In this case, the BPDU is not
processed. You can bring the interface up manually by using the NO
SHUTDOWN command.
Use the no form of the SPANNING-TREE BPDU-GUARD command to
disable the BPDU-guard feature on a bridge.
Command Mode
Configuration Terminal mode
Example
The following commands enable the BPDU Guard feature on a bridge:
switch#configure terminal
switch(config)#spanning-tree portfast bpdu-guard
Related Commands
“SHUTDOWN” on page 181
“SPANNING-TREE PORTFAST BPDU-FILTER DEFAULT” on page 253
- User’s Guide 1
- Contents 3
- Document Conventions 12
- Contacting Allied Telesis 14
- Interface 15
- Introducing the Command Modes 16
- Commands used to 17
- Privileged 18
- Executive 18
- Configuration 19
- Terminal Mode 19
- Line Mode 22
- Username:manager 23
- Password: 23
- Formatting Commands 24
- Command Line 25
- Conventions 25
- Chapter 2 27
- Setting the Switch 28
- Setting a 29
- Gateway Address 29
- Setting the 29
- Network Time 29
- Turning on NTP Authentication 30
- Building configuration 31
- Displaying and 32
- Setting MAC 32
- Addresses 32
- Setting the Aging Time 33
- Adding a Static MAC Address 34
- Removing a Static MAC Address 34
- Uploading an 37
- Image File 37
- Copying a Configuration File 39
- Creating a VLAN 41
- Adding Tagged Ports to a VLAN 42
- Setting the Ports 43
- Setting Port 44
- Speed and Duplex 44
- Enabling and 45
- Disabling Ports 45
- Setting MDI and 45
- Security 46
- Locked Mode 47
- Secured Mode 47
- MAC Address Maximum 47
- Creating Static 49
- Enabling 50
- Backpressure 50
- Enabling Flow 50
- Preventing 51
- Broadcast Storms 51
- Configuring Protocols 53
- Enabling Dynamic VLANs 54
- Setting GVRP Registration 54
- Enabling IGMP 55
- Snooping 55
- Configuring 58
- Authentication 58
- Setting Simple 59
- Management 59
- Protocol (SNMP) 59
- Creating an SNMP Contact Name 60
- Creating SNMP Communities 60
- Setting the Secure 62
- Setting STP and 62
- Setting the Max Age 65
- Setting the Forward Time 65
- Setting the Hello Time 65
- Setting the BPDU Filter 66
- Setting the BPDU Guard 66
- 802.1p Class of 67
- Command Modes 69
- 70 Section I: Command Modes 70
- Chapter 3 71
- 72 Section I: Command Modes 72
- CONFIGURE TERMINAL 79
- COPY A.B.C.D 82
- “COPY DEFAULT.CFG” on page 84 83
- “CP” on page 86 83
- “DOWNLOAD TFTP” on page 87 83
- “UPLOAD TFTP” on page 113 83
- COPY DEFAULT.CFG 84
- “COPY A.B.C.D” on page 82 85
- 86 Section I: Command Modes 86
- DOWNLOAD TFTP 87
- 88 Section I: Command Modes 88
- Section I: Command Modes 89 89
- SHOW INTERFACE 90
- SHOW MAC ADDRESS-TABLE 92
- SHOW MAC ADDRESS-TABLE STATIC 100
- Related Commands 101
- SHOW MAC ADDRESS-TABLE VLAN 102
- SHOW RUNNING-CONFIG INTERFACE 104
- SHOW SPANNING-TREE 106
- Section I: Command Modes 107 107
- SHOW STATIC-CHANNEL-GROUP 109
- SHOW USER-PRIORITY 110
- SYSTEM FACTORY-RESET 111
- SYSTEM REBOOT 112
- UPLOAD TFTP 113
- Configuration Terminal Mode 115
- Commands 115
- 116 Section I: Command Modes 116
- “USERNAME” on page 162 116
- CLOCK SUMMER-TIME RECURRING 117
- Description 118
- Command Mode 118
- CLOCK TIMEZONE 119
- CRYPTO KEY GENERATE USERKEY 121
- DOT1X SYSTEM-AUTH-CTRL 123
- ENABLE PASSWORD 124
- ENABLE SECRET 125
- 126 Section I: Command Modes 126
- Section I: Command Modes 127 127
- HOSTNAME 128
- INTERFACE 129
- IP IGMP SNOOPING 131
- IP ROUTE 132
- IP SSH RSA KEYPAIR-NAME 133
- IP SSH VERSION 134
- LINE CONSOLE 135
- LINE VTY 136
- MAC ADDRESS-TABLE AGEING-TIME 138
- Parameters 139
- MLS QOS 143
- NTP AUTHENTICATE 145
- NTP AUTHENTICATION-KEY 146
- NTP SERVER 148
- NTP TRUSTED-KEY 150
- SHOW LIST 151
- SHOW RUNNING-CONFIG 153
- 154 Section I: Command Modes 154
- Section I: Command Modes 155 155
- 156 Section I: Command Modes 156
- 158 Section I: Command Modes 158
- USERNAME 162
- Interface Configuration Mode 163
- Commands” on page 219 164
- CHANNEL-GROUP 165
- DOT1X PORT-CONTROL 166
- Section I: Command Modes 167 167
- FLOW CONTROL BACKPRESSURE 168
- FLOW CONTROL RECEIVE 169
- FLOW CONTROL SEND 170
- IP ADDRESS 171
- IP ADDRESS DHCP 173
- LACP SYSTEM-PRIORITY 174
- Section I: Command Modes 175 175
- MIRROR INTERFACE DIRECTION 176
- 178 Section I: Command Modes 178
- SHUTDOWN 181
- Examples 183
- STATIC-CHANNEL-GROUP 184
- STORM-CONTROL 185
- SWITCHPORT ACCESS VLAN 187
- SWITCHPORT MODE TRUNK 188
- SWITCHPORT TRUNK ALLOWED VLAN 190
- 192 Section I: Command Modes 192
- USER-PRIORITY 193
- 194 Section I: Command Modes 194
- Advanced Configuration 195
- Chapter 6 197
- LOGIN REMOTELOCAL 200
- RADIUS-SERVER HOST 201
- RADIUS-SERVER KEY 202
- SHOW DOT1X 203
- SHOW DOT1X ALL 204
- SHOW DOT1X INTERFACE 207
- GVRP Commands 211
- SET GVRP 212
- SET GVRP APPLICANT 213
- Chapter 7: GVRP Commands 214
- SET GVRP REGISTRATION 215
- SET GVRP TIMER 217
- Port Security Commands 219
- Example 220
- SWITCHPORT PORT-SECURITY MODE 223
- (SNMP) Commands 227
- SNMP-SERVER COMMUNITY 228
- SNMP-SERVER CONTACT 230
- SNMP-SERVER ENABLE 232
- SNMP-SERVER GROUP 233
- SNMP-SERVER HOST 235
- SNMP-SERVER USER 237
- SNMP-SERVER USER REMOTE 239
- SNMP-SERVER VIEW 241
- Spanning Tree Protocol (STP) 243
- SPANNING-TREE ENABLE FORWARD 247
- SPANNING-TREE FORWARD-TIME 249
- SPANNING-TREE HELLO-TIME 250
- SPANNING-TREE MAX-AGE 251
- SPANNING-TREE MODE 252
- SPANNING-TREE PRIORITY 255
- SHOW VLAN ALL 258
- SHOW VLAN BRIEF 260
- SHOW VLAN DYNAMIC 262
- SHOW VLAN STATIC 263
- VLAN ACCESS-MAP 268
- VLAN DATABASE 269
- Numerics 271
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S100
Hardware De La Computadora Allied-telesis AlliedView-EMS 4.0 INSTALLATION Manual de usuario
(29 paginas)
(29 paginas)
Hardware De La Computadora Allied-telesis Removable Power Supply and Fan Manual de usuario
(23 paginas)
(23 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales