Allied-telesis AT-8116 Manual de usuario Pagina 1

USER’S GUIDE AT-8116Fast Ethernet Intelligent Switch PN 613-10699-00 Rev. A EthernetFastEthernet

2-1 Chapter 2 Command Line Interface This chapter provides instructions for using the AT-8116 CLI. Features of the Command Line Interface The CLI pro

Command Line Interface2-2 Entering Commands Enter commands by typing the command name followed by zero or more parameters and pressing <enter>

AT-8116 User’s Guide2-3To get an explanation of the command’s parameters add a question mark (?) after the command name:SYS_console> ping ??ping IP

Command Line Interface2-4When, as a result of a command, more than one screen-full of text is to be printed, the user may continue to scroll or stop t

AT-8116 User’s Guide2-5Finally, the user may press <?> to see the list of commands which start with the text he has already typed, eg: User pres

Command Line Interface2-6Typing ? at the CLI prompt displays a list of all the available command topics and a short explanation about each. Typing in

3-1Chapter 3Console CommandsThe console commands contain a set of commands which allow the user to configure the CLI parameters and user interface. To

Console Commands3-2bannerThe banner command will display the CentreCOM 8116 Allied Telesyn International logo. clearThe clear command will clear the s

AT-8116 User’s Guide3-3set-attr-promptThis command sets the prompt attributes.SYS_console>set-attr-prompt <number of option>[arg #0] options:

Copyright ® 1998 Allied Telesyn International Corp.All rights reserved. No part of this publication may be reproduced without prior written permissio

Console Commands3-4If the user enters the old password incorrectly or fails to verify the new password correctly, the password will not be changed.SYS

4-1Chapter 4System CommandsThe System Commands allow the user to display and set the system-related parameters. Type <system> to display system

System Commands4-2i/f 1 -- description [Port 1 - 10/100BaseTxETHERNET Port] -- status [UP] i/f 2 -- description [Port 2 - 10/100BaseTxETHERNET Po

AT-8116 User’s Guide4-3get-stst-levelThis command shows the self-test level (Disable or Enable) of the device. Default Value: Enableset-stst-level <

System Commands4-4init-nvramThis command resets the non-volatile RAM (NVRAM) on the SNMP Agent to default values. Change will take effect after boot (

AT-8116 User’s Guide4-5sw-dnldThis command begins the software download process from the remote TFTP server specified by the set-tftp-srvr command, ret

System Commands4-6This command starts frame generation. dport is a dash-separated list of ports on which to generate traffic. For example, a dport of

5-1Chapter 5IP CommandsThis section lists the IP Configuration commands available to the command line interface. It is separated into different section

IP Commands5-2Sets the IP address of the SNMP Agent. If no IP address was previously set (as is the default factory configuration), the new value will

AT-8116 User’s Guide5-3SYS_console>set-ip-cfg 194.90.136.187 255 255.255.0 255.255.255.255 Device IP Address set for this sessionDevice IP Address

i Table of Contents Chapter 1 Administrative Interface ...

IP Commands5-4get-gatewShows default gateway. This command shows which default route will be used to access a different IP network.SYS_console>get

6-1Chapter 6Address Resolution Commandsget-arp-tblShows ARP table. The Address Resolution Protocol (ARP) table contains information that shows the map

Address Resolution Commands6-2add-arp-entry Add entry to ARP table.add-arp-entry <IPaddress> <mac_address> <Interface> (Port MAC add

7-1Chapter 7Ping CommandsPingPerforming a ping allows you to send packets to another managed network device to see if the device responds.Ping <IP

Ping Commands7-2If the host does not respond, only statistics are printed. Failure to get an echo response from a host may be due to:❑ A bad physical

AT-8116 User’s Guide7-3Use CTRL-C or ping-stop to stop the ping processSYS_console>194.90.136.20 Alive. echo reply: id 4643, seq 1, echo-data-len 0

8-1Chapter 8SNMP CommandsThis chapter contains a description of the commands available under the CLI to set and display the SNMP Agent IP and SNMP par

SNMP Commands8-2set-commset-comm {read|write} <community-string>This command lets you specify the SNMP community string for each of the two acce

AT-8116 User’s Guide8-3get-trapsDisplays the list of traps-receiving stations: their IP address and trap SNMP community string.SYS_console>get-trap

Table of Contents ii Chapter 8 SNMP Commands ...

SNMP Commands8-4del-trapThe del-trap command can be used to remove an SNMP station from the trap table. The station IP address must be provided.del-tr

9-1Chapter 9Switching Database CommandsThis section contains instructions for managing the Switching Database with the Administrative Interface. Type

Switching Database Commands9-2❑MAC Address contained in an entry or given as a parameter is printed as a 6 byte, hexadecimal sequence, separated by th

AT-8116 User’s Guide9-3get-lt-16Displays 16 learn table entries starting at <index>, or “ * ” to continue from the last displayed index. The for

Switching Database Commands9-4find-lt-addrSYS_telnet>find-lt-addr 0060e8112265Entry ---- MAC Address ---- LOCK DPORT MGMT==================

AT-8116 User’s Guide9-5Example 3:SYS_telnet>get-vbc-tbl runRUNTIME VIRTUAL BROADCAST DOMAIN TABLE===========================================0 0

Switching Database Commands9-6SYS_console>del-lt-entry 25Deleting entry at index - 25 - OKSYS_console>del-lt-entry 1Cannot delete a System Addr

AT-8116 User’s Guide9-7set-lt-ageset-lt-age {run|nvram|all} <aging_time>Aging _time is between 10 and 11000 seconds or 0 for aging off.Example:S

10-1Chapter 10Virtual LAN CommandsVirtual LANs can be used to limit the broadcast domain and to establish secure virtual workgroups. The following par

1-1 Chapter 1 Administrative Interface The Allied Telesyn International AT-8116 Fast Ethernet switch provides a cost-effective solution for Ethernet

Virtual LAN Commands10-2Virtual Broadcast Domains (VBC)Virtual Broadcast Domains are port-oriented VLANs that allow broadcast Ethernet addresses to be

AT-8116 User’s Guide10-3SYS_console>get-con-matrixVBC CONNECTIVITY MATRIX==========================0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 SRC to : 1 2 3

Virtual LAN Commands10-4set-vbc-domainset-vbc-domain {run|nvram|all} <port_list>This command establishes a Virtual broadcast domain. port_list

AT-8116 User’s Guide10-5NoteAll ports not defined as a member of a VBC are members of the default VBC.get-vbc-matrixRetrieve the current broadcast dom

Virtual LAN Commands10-6Security VLANsEach Security Virtual LAN (SVLAN) can contain one or more groups of ports. The group in a SVLAN are only allowed

AT-8116 User’s Guide10-7set-sec-vlan {run|nvram|all} <group_list>SYS_console>set-sec-vlan run a-bSet Runtime Security Virtual entry - OKSYS_c

Virtual LAN Commands10-8get-svlan-tblThis command shows the table of defined Virtual LANs.get-svlan-tbl {run|nvram}SYS_console>get-svlan-tbl runRUNT

AT-8116 User’s Guide10-9get-svlan-matrixThis command retrieves the Security VLANs connectivity matrix.get-svlan-matrix {run|nvram}SYS_console>get-s

11-1Chapter 11Port Monitoring Commandsset-mon-portThis command sets the monitoring port (port containing the monitoring device, sniffer port). All t

Administrative Interface1-2 The AT-8116 contains a built-in SNMP agent running on the SNMP Processor Board. This allows each unit to be managed from

Port Monitoring Commands11-2save-monThis command saves the current port monitoring information (including set-mon-port and monitor commands) into the

12-1Chapter 12Port Configuration CommandsThis chapter contains instructions for configuring and displaying the ports’ parameters with the Administrative

Port Configuration Commands12-2The information displayed contains:❑ An interface number (port-id)❑ LAN type: ETH-10 indicates 10 Mbps Ethernet ETH-10/

AT-8116 User’s Guide12-3set-speed-selset-port-sel <port-number> {asense|100|10}This command specifies if port-number will negotiate a 10Mbps or 1

13-1Chapter 13Switching Statistics CommandsThis chapter contains instructions for displaying the switching statistics. Type <statistics> to view

Switching Statistics Commands13-2get-eth-cnt <port-number>SYS_console>get-eth-cnt 8Ethernet Statistics for Port 8 ===========================

AT-8116 User’s Guide13-3get-colls-cntThis command displays the Ethernet collision statistics for port port-number.get-colls-cnt <port-number> SY

Switching Statistics Commands13-4get-mgm-brcntRetrieve the counters for the management interface.SYS_console>get-mgm-brcntManagement Port Counters=

14-1Chapter 14Spanning Tree CommandsSpanning Tree automatically configures a loop-free topology in a bridged environment. However, note that the bridg

AT-8116 User’s Guide1-3 Network Management Systems Network management functions greatly assist in monitoring and controlling your network. The AT-811

Spanning Tree Commands14-2get-st-bcfgThis command retrieves the Spanning Tree bridge parameters. If Spanning Tree is disabled, no parameters will be r

AT-8116 User’s Guide14-3set-prt-prioThis command sets the Spanning Tree port priority. port_number is the decimal port number, and port_priority is a

15-1Chapter 15Using an SNMP ManagerThis chapter contains instructions for the configuration and management of the AT-8116 SNMP Management System.Config

Using an SNMP Manager15-2IP Setup 1. Modify the system IP configuration to match your IP network. Use the set-ip-cfg command in order to provide an IP

AT-8116 User’s Guide15-3SNMP Setup 1. Set up the SNMP communities strings for the two access modes: read and write (see SNMP Commands). Confirm that t

16-1Chapter 16Software TroubleshootingThis chapter provides troubleshooting hints for problems you may encounter when trying to manage the AT-8116 usi

A-1Appendix ASoftware DownloadingRequirements❑ Diskette with software file to be downloaded❑ DOS station host (management console, VT100 terminal or V

Administrative Interface1-4 SoftwareRequirements If you are using a workstation, use the VT100 terminal emulation software appropriate for your works

Software DownloadingA-25. Select/Create a directory into which to copy the software file, and enter this directory.6. Copy the software file into a fi

B-1Appendix BSystem DefaultsTable B-1 System Default Values CONSOLEpassword NULLprompt SYS_console>SYSTEMSW filename changes according to revision

C-1Appendix CCommand Line ReferenceTable C-1 Console Commandshelp-kbd List the console functional keysbanner Display bannerclear Clear console screen

Command Line ReferenceC-2Table C-2 System Commandssys-stat Show system status get-stst-level Show self-test level of switchset-stst-level Change the

AT-8116 User’s GuideC-3Table C-3 IP Commandsget-ip Show current IP addressset-ip Set IP addressget-ip-cfg Show current IP configurationset-ip-cfg Set

Command Line ReferenceC-4Table C-5 Switching Database Commandsget-lt-entry Gets an LT entry at indexget-lt-16 Gets 16 LT entries starting at a give

AT-8116 User’s GuideC-5Table C-7 Port Configuration Commandsget-port-cfg Display the configuration of all portsset-port-dplex Set the port mode: full o

AT-8116 User’s Guide1-5 Testing the Installation After you have completed the installation, use the CLI ping command to test for connectivity. See Ch