Allied-telesis AT-S70 Manual de usuario Pagina 268
- Pagina / 302
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix B: DIP Switch Settings
268
AT-CM20x and AT-CM212x/1 Series Line Cards DIP Switches
The AT-CM2xx series line cards feature two sets of DIP switches labeled
“SW1” and “SW 2” as shown in Figure 89.
Figure 89. DIP Switch Sets on an AT-CM2xx Series Line Card
The DIP switches in the SW 1 DIP switch set allow you to set the
operating mode of the line card. For information about the operating
modes, refer to “Configuring the Line Card Operating Mode” on page 67.
The DIP switches in the SW 2 DIP switch set allow you to configure the
MDI/MDI-X feature on the twisted pair port.
Table 6 shows how to enable the operating mode on an AT-CM20x Series
or AT-CM212x/1 Series line card by setting the DIP switches in the SW1
DIP switch set.
“X” means that the DIP switch position can be ON or OFF.
1 2 3 4
1 2 3 4
A
T
-CM20
2
L
K
1 2 3 4
1 2 3 4
SW1
SW2
ON
ON
SW 2 DIP Switch Set
SW 1 DIP Switch Set
Table 6. SW 1 DIP Switch Set (Operating Mode) for the AT-CM20x Series
and AT-CM212x/1 Series Line Cards
Operating Mode DIP 1 DIP 2 DIP 3 DIP 4
Smart MissingLink (SML) OFF ON ON X
MissingLink™ (ML) OFF OFF ON X
OAM Bypass ON OFF OFF X
OAM Visible ON ON OFF X
Link Test (default) OFF OFF OFF X
Manufacturing Default Settings OFF OFF OFF OFF
- User’s Guide 1
- Contents 3
- Contacting Allied Telesis 13
- Chapter 1: Overview 16
- Local Management Session 17
- Remote Management Session 18
- SNMP Management Session 19
- Management Access Levels 20
- Chapter 2 21
- Using the Menus Interface 22
- Quitting from a 25
- Management 25
- Basic Parameters 27
- Assigning an IP 28
- Naming the 30
- Setting the 30
- System Date and 30
- Configuring the 31
- System Location 31
- Information 31
- Chapter 3: Basic Parameters 32
- Management IP 35
- Addresses 35
- Configuring 36
- Community 36
- Pinging a Remote System 38
- Restarting the Line Cards 40
- Using the Omega Option 45
- Setting the Console Timeout 49
- Configuring Management Access 50
- Working with Line Cards 51
- Line Card Management Overview 52
- Displaying 53
- General Status 53
- Detailed Line 54
- Card Information 54
- Displaying Line 56
- Card DIP Switch 56
- Settings 56
- Display DIP Switch Setting 57
- Module 5 57
- --: No link 60
- Online: Valid link 60
- Enabling and 61
- Disabling the 61
- Ports on a Line 61
- Changing the 62
- Line Card Port 62
- Duplex Mode 62
- Port Ingress/ 63
- Egress Rate Limit 63
- MissingLink 68
- Displaying Status 72
- Local Console 74
- T1/E1 Port 75
- TDM Management Menu 76
- Module 15, Port C 76
- TDM Port Configurations 76
- UART Configurations 76
- Long Haul (default) 78
- Displaying Port 82
- Working with a 83
- Redundant 83
- AT-CV5M01 83
- Resetting the 84
- Maximum Frame 85
- Traffic Statistics 86
- Setting the Port 88
- Ingress and 88
- Egress Rate 88
- Port Ingress and 90
- Monitoring System Performance 91
- Starting and 93
- Stopping the 93
- Activity Monitor 93
- Activity Log 93
- Using the System Diagnostics 94
- Event Log and Syslog Servers 103
- Event Log Overview 104
- Working with the Event Log 105
- Clearing the 107
- Event Log 107
- Configuring the Syslog Server 108
- Maintenance (OAM) 111
- Overview 112
- OAMPDU Types 113
- OAM Remote 114
- Loopback 114
- MIB Variable 114
- Retrieval and 114
- Extensions 114
- Displaying OAM 120
- Information for a 120
- Local Module 120
- Remote Module 125
- Statistics 126
- OAM Loopback Test 129
- Starting or 130
- Stopping a 130
- Loopback Test 130
- Displaying or 131
- Converteon 133
- Chapter 9 135
- SNMPv3 Overview 136
- SNMPv3 Privacy 137
- Protocol 137
- SNMPv3 MIB 138
- SNMPv3 Storage 139
- SNMPv3 Message 139
- Notification 139
- SNMPV3 Auth Table 140
- SNMPv3 User Table 140
- SNMPv3 View Table 140
- SNMPv3 Access Table 140
- SNMPv3 Group Table 143
- SNMPv3 Notify Table 143
- SNMPv3 Target Address Table 143
- Configuration 144
- Configuring SNMPv3 Entities 145
- Creating an 146
- SNMPv3 User 146
- Table Entry 146
- Chapter 9: SNMPv3 148
- Enter Privacy Password: 149
- Deleting an 150
- Modifying an 152
- Enter User (Security) Name: 153
- Modifying the Storage Type 156
- Displaying the 157
- Table Menu 157
- SNMPv3 View 159
- 1.3.6.1.2.1.2.2.1.0.3 161
- Modifying a View Type 165
- Modifying a Storage Type 166
- SNMPv3 Access 169
- NoauthNoPriv]: 171
- Enter Read View Name: 171
- Enter Write View Name: 172
- Enter Notify View Name: 172
- Enter Group Name: 178
- SNMPv3 Group 186
- SNMPv3 Notify 195
- Modifying a Notify Type 200
- SNMPv3 Target 204
- Address Table 204
- Enter IP Address: 210
- Enter Target Address Name: 210
- Enter Tag List: 214
- Enter Target Parameters: 215
- Parameters Table 220
- Modifying the Security Model 226
- Enter Target Parameters Name: 227
- Modifying the Security Level 228
- Saving SNMPv3 Configuration 234
- Loading SNMPv3 Configuration 235
- File Downloads and Uploads 237
- Guidelines 239
- File Guidelines 239
- Downloading the 241
- AT-S70 Software 241
- Image File Using 241
- Line Card Image 247
- Enter LineCard Slotnum: -> 248
- TFTP Server IP Address-> 248
- Image File Name-> 248
- Line Card 249
- Bootloader File 249
- Downloading a 257
- Uploading a 258
- AT-S70 Default Settings 261
- Threshold 262
- Settings Default 262
- DIP Switch Settings 263
- DIP Switch Features 264
- 1 2 3 4 266
- 1 2 3 4 271
- 4 3 2 1 271
- AT-CM70S Line Card DIP Switch 272
- SNMPv3 Configuration Examples 273
- Configure SNMPv3 Access Table 274
- Configure SNMPv3 Group Table 274
- Operator 275
- Worksheet 277
- Appendix D 279
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S70
(64 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales