Allied-telesis AT-S62 Manual de usuario Pagina 279
- Pagina / 372
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-S62 Management Software Web Browser Interface User’s Guide
Section IV: Spanning Tree Protocols 279
Configuring RSTP
Caution
The bridge provides default RSTP parameters that are adequate for
most networks. Changing them without prior experience and an
understanding of how RSTP works might have a negative effect on
your network. You should consult the IEEE 802.1w standard before
changing any of the RSTP parameters.
This procedure assumes that you have already designated RSTP as the
active spanning tree on the switch. For instructions, refer to “Enabling or
Disabling Spanning Tree” on page 272.
To configure RSTP, perform the following procedure:
1. In the Spanning Tree tab, Configure Spanning Tree Parameters
section, click Configure.
The RSTP Spanning Tree tab is shown in Figure 94.
Figure 94. RSTP Spanning Tree Tab
- Web Browser Interface 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 14
- Document Conventions 15
- Contacting Allied Telesyn 17
- New Features History 18
- Chapter 1 23
- Switch’s IP Address 24
- Browser Tools 27
- Saving Your Parameter Changes 28
- Basic Switch Parameters 33
- Rebooting a Switch 44
- Pinging a Remote System 48
- Enhanced Stacking 53
- Chapter 3: Enhanced Stacking 54
- SNMPv1 and SNMPv2c Community 61
- Port Parameters 71
- Configuring Port Parameters 72
- Chapter 5: Port Parameters 76
- Chapter 6: MAC Address Table 84
- Creating a Static Port Trunk 94
- Modifying a Static Port Trunk 97
- Chapter 7: Static Port Trunks 98
- Port Mirroring 101
- Creating a Port Mirror 102
- Chapter 8: Port Mirroring 104
- Deleting a Port Mirror 106
- Displaying the Port Mirror 107
- File System 111
- Chapter 9: File System 112
- File Downloads and Uploads 115
- Downloading a File 116
- Uploading a File 119
- Event Log and Syslog Servers 121
- Managing the Event Log 122
- Displaying the 124
- Event Log 124
- Modifying the 127
- Event Log Full 127
- Saving the Event 128
- Clearing the 128
- Creating a Syslog 130
- Server Definition 130
- LOCAL6 133
- LOCAL7 133
- Viewing a Syslog 135
- Classifiers 137
- Creating a Classifier 138
- Chapter 12: Classifiers 140
- Modifying a Classifier 144
- Deleting a Classifier 145
- Displaying the Classifiers 146
- Access Control Lists 147
- Quality of Service 155
- Managing Flow Groups 156
- Modifying a Flow 158
- Deleting a Flow 160
- Displaying Flow 160
- Managing Traffic Classes 162
- Modifying a 166
- Traffic Class 166
- Deleting a Traffic 167
- Traffic Classes 168
- Managing Policies 169
- Displaying 173
- Policies 173
- Class of Service 175
- Configuring CoS 176
- Chapter 15: Class of Service 178
- Configuring Egress Scheduling 180
- Displaying the CoS Settings 181
- Configuring IGMP Snooping 184
- Chapter 16: IGMP Snooping 186
- Router IP 188
- Denial of Service Defense 189
- Displaying the DoS Settings 193
- Power Over Ethernet 195
- Setting the PoE Threshold 196
- Configuring PoE Port Settings 198
- SNMPv3 Operations 203
- Chapter 19 205
- Enabling the SNMP Protocol 206
- Section III: SNMPv3 207 207
- Section III: SNMPv3 209 209
- Chapter 19: SNMPv3 210
- 210 Section III: SNMPv3 210
- 212 Section III: SNMPv3 212
- 214 Section III: SNMPv3 214
- 216 Section III: SNMPv3 216
- Deleting a View 218
- Table Entry 218
- Modifying a View 219
- 220 Section III: SNMPv3 220
- 222 Section III: SNMPv3 222
- 224 Section III: SNMPv3 224
- Deleting an 226
- Access Table 226
- Modifying an 227
- 228 Section III: SNMPv3 228
- 230 Section III: SNMPv3 230
- defaultV1GroupReadOnly 230
- SecurityToGroup 232
- Section III: SNMPv3 233 233
- defaultV1GroupReadWrite 233
- defaultV2cGroupReadOnly 233
- defaultV2cGroupReadWrite 233
- Section III: SNMPv3 235 235
- Notify Table 237
- 238 Section III: SNMPv3 238
- 240 Section III: SNMPv3 240
- Deleting a Target 242
- Address Table 242
- Modifying Target 243
- 244 Section III: SNMPv3 244
- Creating a Target 246
- Parameters Table 246
- Section III: SNMPv3 247 247
- Section III: SNMPv3 251 251
- Creating an 253
- Community 253
- 254 Section III: SNMPv3 254
- 258 Section III: SNMPv3 258
- Displaying User 260
- Table Entries 260
- Displaying View 261
- Displaying Access 262
- Displaying Notify 264
- Displaying Target 265
- 268 Section III: SNMPv3 268
- Chapter 20 271
- Configuring STP 274
- Configuring RSTP 279
- Configuring MSTP 283
- Associating 286
- VLANs to MSTIs 286
- Configuring 289
- MSTP Port 289
- Parameters 289
- Internal path cost 290
- Port priority 290
- Virtual LANs 295
- 296 Section V: Virtual VLANs 296
- 298 Secton V: Virtual LANs 298
- 300 Secton V: Virtual LANs 300
- Secton V: Virtual LANs 303 303
- Displaying VLANs 305
- 306 Secton V: Virtual LANs 306
- Specifying a Management VLAN 308
- Secton V: Virtual LANs 309 309
- 310 Secton V: Virtual LANs 310
- Configuring GVRP 312
- Section V: Virtual LANs 313 313
- Section V: Virtual LANs 315 315
- Protected Ports VLANs 317
- 318 Section V: Virtual LANs 318
- 320 Section V: Virtual LANs 320
- 322 Section VI: Port Security 322
- 324 Section VI: Port Security 324
- 326 Section VI: Port Security 326
- 328 Section VI: Port Security 328
- 330 Section VI: Port Security 330
- 6. Click Apply 332
- Setting Port Roles 333
- 334 Section VI: Port Security 334
- Section VI: Port Security 337 337
- Section VI: Port Security 339 339
- 340 Section VI: Port Security 340
- 342 Section VI: Port Security 342
- Encryption Keys, PKI, and SSL 345
- Displaying Encryption Keys 346
- Displaying the SSL Settings 350
- Secure Shell Protocol 351
- Configuring the SSH Server 352
- Displaying SSH Information 354
- Protocols 355
- Chapter 29 361
- Creating an ACE 364
- Deleting an ACE 366
- Displaying the Management ACL 367
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S62
(61 paginas)
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales