Allied Telesis AT-S80 Guía de usuario Pagina 185
- Pagina / 242
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-S80 Management Software User’s Guide
Section II: Using the Web Browser Interface 185
When selecting a setting, note the following:
When a twisted pair port is set to Auto-Negotiation, the default
setting, the end node should also be using Auto-Negotiation to
prevent a duplex mode mismatch. A switch port using Auto-
Negotiation defaults to half-duplex if it detects that the end node is
not using Auto-Negotiation. This can result in a mismatch if the end
node is operating at a fixed duplex mode of full-duplex. To avoid
this problem when connecting an end node with a fixed duplex
mode of full-duplex to a switch port, disable Auto-Negotiation on
the port and set the port’s speed and duplex mode manually.
For 1000 Mbps operation on an uplink 10/100/1000Base-T twisted
pair uplink port, Allied Telesyn recommends using Auto-
Negotiation. Setting the speed and duplex mode manually to 1000
Mbps full duplex is not recommended.
The only valid setting for an optional SFP port is Auto-Negotiation.
Flow Control
The current flow control setting on the port. The switch uses a special
pause packet to notify the end node to stop transmitting for a specified
period of time. The possible values are:
Enabled - The port uses flow control. This is the default setting for all
ports on the switch.
Disabled - The port does not use flow control.
MAC Address
The port’s MAC address. You cannot change this setting.
3. Click Apply.
4. To view or configure the parameter settings on another port, do the
following:
a. Click Go to Port and select the port from the pull-down menu,
b. Click Apply.
c. Configure the parameters as needed. Refer to Step 2 in this
procedure for definitions of the parameters.
- User’s Guide 1
- Contents 3
- Document Conventions 13
- Contacting Allied Telesyn 14
- Overview 15
- Management Overview 16
- Local Management Connection 17
- Remote Management Connection 18
- Management Access Level 19
- AT-FS750/24 Switch 20
- Using the Menus Interface 21
- Interface 23
- Enter system location> 35
- Enter system contact> 35
- Enter current password> 37
- Enter new password> 38
- Retype new password> 38
- Enter old password> 38
- Viewing Switch Information 39
- Rebooting the Switch 42
- Enter new timeout value> 45
- Figure 12. Ping Results 46
- Chapter 4: Port Configuration 50
- Enabling and Disabling a Port 52
- Enter new mode for port 53
- (a/h/H/f/F/T)> 53
- Port Trunking Overview 58
- Trunk” on page 65 59
- (E/D)> 62
- Chapter 5: Port Trunking 64
- Enter trunk group number> 65
- Port Mirroring Overview 68
- Chapter 6: Port Mirroring 70
- VLAN Features 74
- Port-based VLANs 75
- Tagged VLANs 75
- Port-based VLAN Overview 76
- Drawbacks of 78
- Example 1 79
- Example 2 80
- Tagged VLAN Overview 82
- Tagged VLAN 84
- Enter port number > 88
- Chapter 7: Virtual LANs 90
- QoS Overview 98
- Chapter 9 107
- RSTP Overview 108
- Path Costs and Port Costs 109
- Port Priority 110
- Point-to-Point and Edge Ports 111
- Point-to-Point Ports 112
- (Full-duplex Mode) 112
- RSTP Networks 113
- Mixed STP and 113
- Rapid Spanning 114
- Tree and VLANs 114
- Enabling or Disabling RSTP 115
- Enter bridge priority> 118
- Enter bridge hello time> 118
- Enter bridge maximum age> 119
- Configuring STP Compatibility 120
- Configuring the 121
- Basic RSTP Port 121
- Settings 121
- Advanced RSTP 123
- Port Settings 123
- Displaying the RSTP Topology 126
- Chapter 10 129
- Authentication 131
- Authenticator 131
- Port-based 133
- Network Access 133
- Guidelines 133
- Switch A 135
- Switch B 135
- Enter port number> 137
- Chapter 11 141
- RADIUS Overview 142
- Configuring the RADIUS Client 143
- Enter response time> 144
- Broadcast Storm Control 147
- Management Software Updates 151
- Enter file name> 154
- Enter retry count> 154
- Download file? (Y/N)> 154
- Section II 155
- Chapter 14 157
- Switch’s IP Address 158
- Web Browser Tools 161
- Basic Switch Parameters 163
- System Contact 168
- 3. Click Apply 168
- Console UI Idle Time Out 170
- Web Server 170
- User name and password 170
- Viewing System Information 172
- DHCP Mode 174
- Client” on page 166 174
- Rebooting a Switch 175
- Pinging a Remote System 176
- 3. Click Start 177
- Port Configuration 179
- 10/100BaseTX - Base ports 181
- Displaying Port Statistics 186
- Port Trunking 189
- Creating a Port Trunk 190
- Modifying a Port Trunk 192
- Chapter 17: Port Trunking 194
- Port Mirroring 195
- Configuring Port Mirroring 196
- Disabling Port Mirroring 197
- Chapter 18: Port Mirroring 198
- Virtual LANs 199
- Creating a VLAN 200
- Chapter 19: Virtual LANs 202
- Displaying the VLANs 204
- Figure 60 205
- Modifying a VLAN 206
- Deleting a VLAN 208
- Quality of Service (QoS) 209
- Chapter 21 215
- Basic RSTP Configuration 216
- Bridge Forward Delay 218
- 5. Click Apply 222
- Viewing the RSTP Topology 223
- Chapter 22 225
- Chapter 23 229
- Appendix A 237
Relacionado con productos y manuales para Software Allied Telesis AT-S80
Software Allied Telesis AT-8000S Guía de usuario
(204 paginas)
(204 paginas)
Software Allied Telesis AT-S82 Guía de usuario
(76 paginas)
(76 paginas)
(49 paginas)
Software Allied Telesis AT-S80 Guía de instalación
(44 paginas)
(44 paginas)
Software Allied Telesis AT-9000/52 Guía de usuario
(19 paginas)
(19 paginas)
Software Allied Telesis AT-S94 Manual de usuario
(20 paginas)
(20 paginas)
Software Allied Telesis AT-8100S/24C Guía de usuario
(350 paginas)
(350 paginas)
Software Allied Telesis AT-FS750/48 Guía de usuario
(234 paginas)
(234 paginas)
Software Allied Telesis AT-GS950/16 Guía de usuario
(348 paginas)
(348 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales