Allied-telesis AT-S97 Manual de usuario Pagina 27
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide
27
What to Configure First
This section has a few suggestions on what to configure when you are
managing the chassis for the first time. The initial management session
must be a local session. For instructions on how to start a local
management session, refer to “Starting a Local Management Session” on
page 20.
Note
Although the management module comes with the default IP
address 10.0.0.1 and subnet mask 255.255.252.0, the initial
configuration of the chassis cannot be a remote session because the
module’s Telnet and SSH servers are initially disabled.
Displaying the
Chassis Modules
After logging on, enter this command:
system show cluster
The command displays the management and media converter modules in
the chassis. You can use this information to verify the modules in the unit.
An example is shown in Figure 4.
Figure 4. Displaying the Chassis Modules with the SYSTEM SHOW
CLUSTER Command
For information on this command, refer to “SYSTEM SHOW CLUSTER”
on page 88.
Chassis Chassis Chassis MAC Master
ID Name Type Address Chassis
------------------------------------------------------------------
0 AT-MCF2000 11:22:33:44:55:55 Yes
Slot ID Module Name Module Type Software Version
------------------------------------------------------------
M AT-MCF2000M v1.3.0
1 AT-MCF2012LC v1.3.0
2 AT-MCF2012LC v1.3.0
Chassis information
Management and media converter module information
- Command Line Interface 1
- User’s Guide 1
- Contents 3
- Document Conventions 12
- Contacting Allied Telesis 14
- Chapter 1 15
- Management Overview 16
- Chassis ID 18
- Chassis ID 0 19
- (Default) 19
- Chassis ID 31 19
- Chassis ID Jumper 19
- AT-MCF2KFAN 20
- <No System Name> 21
- Quitting a Management Session 24
- Command Formatting 26
- What to Configure First 27
- Assigning an IP 30
- Setting the Date 31
- Enabling the 31
- Telnet or Secure 31
- Shell Server 31
- Saving Your 32
- Basic Commands 33
- Question Mark ‘?’ Key 34
- Parameter 38
- IP Configuration Commands 39
- IP DHCP DISABLE 42
- IP DHCP ENABLE 43
- General System Commands 47
- SYSTEM SET ASYNCHRONOUS 50
- SYSTEM SET CHASSIS 51
- SYSTEM SET CLOCK 52
- SYSTEM SET CONSOLE 53
- SYSTEM SET CONTACT 54
- SYSTEM SET HOSTNAME 55
- SYSTEM SET LOCATION 56
- SYSTEM SHOW ASYNCHRONOUS 57
- SYSTEM SHOW CLOCK 58
- SYSTEM SHOW CONSOLE 59
- SYSTEM SHOW INFO 60
- Port and Module Commands 61
- SYSTEM RESET CHASSIS 64
- SYSTEM RESET CLUSTER 66
- SYSTEM RESET MODULE 68
- SYSTEM SET INTERFACE 71
- Mode Select Button 75
- Operating Mode Guidelines 75
- SYSTEM SET MODULE 77
- SYSTEM SET PORT 80
- SYSTEM SHOW CHASSIS 86
- SYSTEM SHOW CLUSTER 88
- SYSTEM SHOW INTERFACE 90
- SYSTEM SHOW MODULE 97
- Examples 100
- Chapter 6 101
- Overview 102
- NTP client 103
- Command Description 103
- NTP DISABLE 104
- NTP ENABLE 105
- Parameters 106
- Privilege Levels 106
- Description 106
- NTP SHOW 107
- Chapter 7 109
- LOGGING CLEAR EVENTLOG 112
- LOGGING DISABLE EVENTLOG 113
- LOGGING DISABLE SYSLOG 114
- LOGGING ENABLE EVENTLOG 115
- LOGGING ENABLE SYSLOG 116
- LOGGING SET EVENTLOG 117
- LOGGING SET SYSLOG 119
- LOGGING SHOW 120
- LOGGING SHOW EVENTLOG 122
- Configuration File Commands 129
- Creating a New 131
- Configuration 131
- Editing a Master 133
- File Header Lines 134
- System Configuration 134
- IP Configuration 135
- Log Configuration 135
- NTP Configuration 136
- Telnet and SSH Configuration 136
- User Configuration 136
- Blade Configuration 137
- CONFIG RUN 141
- CONFIG SAVE 142
- CONFIG SAVE FILESYSTEM 143
- CONFIG SET 145
- CONFIG SHOW 147
- File System Commands 149
- Guidelines to 151
- Using the TFTP 151
- FILE COPY 153
- FILE DELETE 156
- FILE DOWNLOAD 159
- General Description 161
- Description of Syntax 1 161
- Description of Syntax 2 162
- Description of Syntax 3 163
- Description of Syntax 4 163
- Software 164
- FILE RENAME 166
- FILE SHOW 169
- FILE UPLOAD 172
- Telnet Server Commands 175
- TELNET DISABLE 178
- TELNET ENABLE 179
- TELNET SHOW 180
- Secure Shell Server Commands 181
- SSH DISABLE 184
- SSH ENABLE 185
- SSH SHOW 186
- Manager Account Commands 187
- USER ADD 190
- USER DELETE 191
- USER SET 192
- Adams” account: 193
- USER SHOW 194
- Diagnostics Commands 195
- DIAGNOSTICS SHOW CHASSIS 197
- DIAGNOSTICS SHOW MODULE 199
- AT-S85 and AT-S97 Management 203
- Software Default Settings 203
- Event Log 204
- Manager Account 206
- Master Configuration File 207
- Network Time Protocol Client 208
- RS-232 Terminal Port 209
- Secure Shell Server 210
- Syslog Client 211
- Telnet Server 212
- Numerics 213
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S97
Hardware De La Computadora Allied-telesis SwitchBlade Bandwidth Expander Manual de usuario
(6 paginas)
(6 paginas)
Hardware De La Computadora Allied-telesis SwitchBlade Chassis and Fan Tray Manual de usuario
(11 paginas)
(11 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales