Allied-telesis AT-S97 Manual de usuario Pagina 200
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 13: Diagnostics Commands
200
Figure 40. DIAGNOSTICS SHOW MODULE Command
The fields in the display are defined here:
Name - The name of the module. Refer to “SYSTEM SET MODULE”
on page 77 for instructions on assigning a name to a module.
Model - The model name.
MAC - The module’s MAC address.
SN - The module’s serial number.
HW Rev. - The module’s hardware revision level.
Software Version - The version number of the AT-S85 or AT-S97
Management Software.
Voltages - Input voltages on the module.
Temperature - The current temperature of the module.
Temperature Threshold - The temperature threshold of a module. The
management module logs an event in the event log if the threshold is
exceeded, to warn of possible excessive temperature in the wiring
closet or chassis. Refer to “SYSTEM SET MODULE” on page 77 for
instructions on setting a module’s temperature threshold.
Eeprom Information
Name .......................
Model ...................... AT-MCF2012LC
MAC ........................ 00:15:77:70:7A:22
SN ......................... 14
HW Rev ..................... 1
CPU Software Information:
Software Version ........... v1.3.0
CPU Information:
Name .......................
Module Type ................ AT-MCF2012LC
Module Status .............. Active
Module Present ............. Present
1.2V ....................... Good = 1.198
1.8V ....................... Good = 1.804V
2.5V ....................... Good = 2.509
3.3V ....................... Good = 3.302V
12.0V ...................... Good = 12.6224
Temperature ................ 38.15V
Temperature Threshold ...... 60 C
- Command Line Interface 1
- User’s Guide 1
- Contents 3
- Document Conventions 12
- Contacting Allied Telesis 14
- Chapter 1 15
- Management Overview 16
- Chassis ID 18
- Chassis ID 0 19
- (Default) 19
- Chassis ID 31 19
- Chassis ID Jumper 19
- AT-MCF2KFAN 20
- <No System Name> 21
- Quitting a Management Session 24
- Command Formatting 26
- What to Configure First 27
- Assigning an IP 30
- Setting the Date 31
- Enabling the 31
- Telnet or Secure 31
- Shell Server 31
- Saving Your 32
- Basic Commands 33
- Question Mark ‘?’ Key 34
- Parameter 38
- IP Configuration Commands 39
- IP DHCP DISABLE 42
- IP DHCP ENABLE 43
- General System Commands 47
- SYSTEM SET ASYNCHRONOUS 50
- SYSTEM SET CHASSIS 51
- SYSTEM SET CLOCK 52
- SYSTEM SET CONSOLE 53
- SYSTEM SET CONTACT 54
- SYSTEM SET HOSTNAME 55
- SYSTEM SET LOCATION 56
- SYSTEM SHOW ASYNCHRONOUS 57
- SYSTEM SHOW CLOCK 58
- SYSTEM SHOW CONSOLE 59
- SYSTEM SHOW INFO 60
- Port and Module Commands 61
- SYSTEM RESET CHASSIS 64
- SYSTEM RESET CLUSTER 66
- SYSTEM RESET MODULE 68
- SYSTEM SET INTERFACE 71
- Mode Select Button 75
- Operating Mode Guidelines 75
- SYSTEM SET MODULE 77
- SYSTEM SET PORT 80
- SYSTEM SHOW CHASSIS 86
- SYSTEM SHOW CLUSTER 88
- SYSTEM SHOW INTERFACE 90
- SYSTEM SHOW MODULE 97
- Examples 100
- Chapter 6 101
- Overview 102
- NTP client 103
- Command Description 103
- NTP DISABLE 104
- NTP ENABLE 105
- Parameters 106
- Privilege Levels 106
- Description 106
- NTP SHOW 107
- Chapter 7 109
- LOGGING CLEAR EVENTLOG 112
- LOGGING DISABLE EVENTLOG 113
- LOGGING DISABLE SYSLOG 114
- LOGGING ENABLE EVENTLOG 115
- LOGGING ENABLE SYSLOG 116
- LOGGING SET EVENTLOG 117
- LOGGING SET SYSLOG 119
- LOGGING SHOW 120
- LOGGING SHOW EVENTLOG 122
- Configuration File Commands 129
- Creating a New 131
- Configuration 131
- Editing a Master 133
- File Header Lines 134
- System Configuration 134
- IP Configuration 135
- Log Configuration 135
- NTP Configuration 136
- Telnet and SSH Configuration 136
- User Configuration 136
- Blade Configuration 137
- CONFIG RUN 141
- CONFIG SAVE 142
- CONFIG SAVE FILESYSTEM 143
- CONFIG SET 145
- CONFIG SHOW 147
- File System Commands 149
- Guidelines to 151
- Using the TFTP 151
- FILE COPY 153
- FILE DELETE 156
- FILE DOWNLOAD 159
- General Description 161
- Description of Syntax 1 161
- Description of Syntax 2 162
- Description of Syntax 3 163
- Description of Syntax 4 163
- Software 164
- FILE RENAME 166
- FILE SHOW 169
- FILE UPLOAD 172
- Telnet Server Commands 175
- TELNET DISABLE 178
- TELNET ENABLE 179
- TELNET SHOW 180
- Secure Shell Server Commands 181
- SSH DISABLE 184
- SSH ENABLE 185
- SSH SHOW 186
- Manager Account Commands 187
- USER ADD 190
- USER DELETE 191
- USER SET 192
- Adams” account: 193
- USER SHOW 194
- Diagnostics Commands 195
- DIAGNOSTICS SHOW CHASSIS 197
- DIAGNOSTICS SHOW MODULE 199
- AT-S85 and AT-S97 Management 203
- Software Default Settings 203
- Event Log 204
- Manager Account 206
- Master Configuration File 207
- Network Time Protocol Client 208
- RS-232 Terminal Port 209
- Secure Shell Server 210
- Syslog Client 211
- Telnet Server 212
- Numerics 213
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S97
Hardware De La Computadora Allied-telesis SwitchBlade Bandwidth Expander Manual de usuario
(6 paginas)
(6 paginas)
Hardware De La Computadora Allied-telesis SwitchBlade Chassis and Fan Tray Manual de usuario
(11 paginas)
(11 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales