Allied-telesis AT-S41 Manual de usuario Pagina 193
- Pagina / 236
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-S41 User’s Guide
193
Configuring a Bridge’s STP Settings
Caution
STP on a bridge is disabled by default. If you enable STP, the bridge
provides default STP parameters that are adequate for most
networks. Changing them without prior experience and an
understanding of how STP works might have a negative effect on
your network. You should consult the IEEE 802.1d standard before
changing any of the STP parameters.
To configure a bridge’s STP parameters, perform the following
procedure:
1. Click on the Basic Config menu tab and select Spanning Tree from the
sub-menu. Choose STP Config from the next sub-menu.
The Spanning Tree Bridge Configuration page will appear, as
displayed in Figure 65.
Figure 65 Spanning Tree Bridge Configuration
2. Adjust the bridge STP settings as needed. The parameters are
described below.
Enable/Disable STP
Enables and disables STP on the switch. The default setting is
disabled.
- User’s Guide 1
- Table of Contents 3
- Section III 6
- List of Figures 8
- How This Guide is Organized 10
- Document Conventions 11
- Overview 15
- Management Software Overview 16
- Local Management Session 18
- Telnet Management Session 19
- SNMP Management Session 21
- Stacking 22
- Stacking Overview 23
- Local and Telnet Management 25
- Starting a Local or Telnet 26
- Starting a Local 28
- Command> 29
- Local Session 30
- AT-8326GB 33
- How Do You 33
- Assign an IP 33
- Address? 33
- Port Security Overview 59
- Setting a Threshold 63
- Setting Intrusion Detection 64
- Port Trunking 65
- Port Trunking Overview 66
- Creating a Port Trunk 69
- Enter trunk group number-> 70
- Deleting a Port Trunk 71
- Setting Port Trunk Status 72
- Port Monitoring Overview 74
- Enabling Port Monitoring 75
- Modifying Port Monitoring 77
- Disabling Port Monitoring 78
- STP Overview 80
- Finding and 81
- Resolving 81
- Redundant 81
- VLAN Overview 90
- Tagged Ports 93
- Untagged and 93
- General Rules 95
- Untagged or 95
- Tagged VLAN 95
- Enter PVID for port 1> 100
- Enter VLAN ID> 101
- AT-S41 User’s Guide 102
- Port-based VLAN Mode Overview 106
- Creating a Port-based VLAN 107
- Enter Stack ID > 108
- Enter port number> 108
- Modifying a Port-based VLAN 110
- Setting GVRP Status 112
- Setting the VLAN Type 114
- MAC Address Table 115
- MAC Address Overview 116
- Displaying MAC Addresses 118
- Viewing MAC Addresses by Port 120
- Adding Static MAC Addresses 123
- Deleting Static MAC Addresses 124
- Changing the Aging Time 125
- Quality of Service 126
- Quality of Service Overview 127
- Configuring QoS 128
- Queue is in range of 0 to 1 129
- IGMP Snooping 130
- IGMP Snooping Overview 131
- Activating IGMP Snooping 132
- Viewing Group Members 134
- Group Members 135
- Broadcast Storm Control 136
- Port Statistics 139
- Displaying Port Statistics 140
- Management Software Updates 143
- Obtaining Software Updates 144
- Management Session 145
- Download file (Y/N)> 150
- Web Browser Management 151
- Starting a Web Browser 152
- Switch’s IP Address 153
- Quitting from a 155
- Web Browser 155
- Management 155
- Basic Switch Parameters 156
- Configuring an IP Address 157
- Activating DHCP 163
- Rebooting a Switch 167
- Ping Execution 169
- Bootstrap Configuration 171
- Port Parameters 173
- Configuring Port Parameters 174
- Configuring Gigabit Port Type 177
- Displaying Port Status 178
- Port Security 183
- Configuring Port Security 184
- Port Trunks 187
- Port Monitoring 190
- Configuring Port Monitoring 191
- Spanning Tree Protocol 192
- Configuring STP Port Settings 195
- Virtual LANs 197
- AT-S41 Default Settings 235
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S41
Hardware De La Computadora Allied-telesis SWITCHBLADE POWER SUPPLY UNIT Manual de usuario
(10 paginas)
(10 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 2.3 MIB COMPILER Manual de usuario
(14 paginas)
(14 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 2.3 VLAN MANAGER Manual de usuario
(47 paginas)
(47 paginas)
Hardware De La Computadora Allied-telesis AT-VIEW PLUS 2.3 DEVICE MANAGER Manual de usuario
(121 paginas)
(121 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales