Allied-telesis AT-S99 Manual de usuario Pagina 100
- Pagina / 320
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 4: Configuring the AT-CV5M02 Management Card
100
Table 9 lists the event messages.
Table 9. Event Log Messages
Message Chassis
Classi-
fication
Definition
n Voltage Failed AT-CV5000 Report The AT-PWR14 or AT-PWR15 Power
Supply Module in the AT-CV5000 Chassis
had an output voltage failure. The variable
n can be 3.3V, 5V, or 12V and signals
which voltage failed.
Clear The AT-PWR14 or AT-PWR15 Power
Supply Module resumed normal
operations or was replaced.
Copper port failure on
remote linecard n.
AT-CV1200
AT-CV1203
AT-CV5000
Report The twisted pair port on a remote AT-CM
Line Card lost its link to its network
device. This message requires remote
peer management.
Clear The twisted pair port on a remote AT-CM
Line Card established a link to its network
device. This messages requires remote
peer management.
CPM Card Reboot AT-CV1200
AT-CV1203
AT-CV5000
Report The AT-CV5M02 Management Card was
reset.
CV1203 Local RPS
Failure A/B
AT-CV1203 Report One of the two external power supplies
connected to the AT-CV1203 Chassis
failed. (A failed power supply has no
detectable output voltages.) “A” and “B”
designate the power connectors on the
back panel of the chassis. This message
only appears if the AT-CV1203 Chassis
has two power supplies and just one of
the power supplies fails.
Clear A power supply connected to the
AT-CV1203 Chassis resumed normal
operations or was replaced.
- User’s Guide 1
- Contents 3
- Contacting Allied Telesis 17
- Management 18
- Software Updates 18
- AT-CV5M02 Management Card 19
- The Converteon Product Line 20
- AT-S99 Management Software 22
- Console Port 22
- 10/100Base-TX Port 22
- IP Address Configuration 23
- Event Log 23
- Activity Monitor 23
- Syslog Client 23
- Network Time Protocol Client 24
- Manager and Operator Accounts 24
- Management Access 25
- Redundant Management Cards 26
- Access to Your Network 28
- Configuration Files 29
- Restoring 30
- Configurations to 30
- AT-CM Line 30
- Cards and 31
- Remote Peer 31
- Redundant 32
- Converteon Chassis 34
- Line Cards 35
- 2. Four T1/E1 ports 38
- Link Test 40
- MissingLink 40
- Smart MissingLink 40
- Operating Modes 42
- MissingLink 43
- OAM-based Features 46
- Local line cards in the 49
- Remote line cards 49
- OAM Loopback 51
- OAM Variable 55
- Requests 55
- OAM Client 56
- Starting a Management Session 57
- AT-CV501 58
- > Enable this port 60
- Disable this port 60
- System name: -> 60
- Figure 12. Chassis View 63
- Switch Over Management Cards 67
- Changing the 69
- Manager and 69
- Passwords 69
- Setting the Date 71
- Naming the 72
- Saving Your 72
- Configuring the AT-CV5M02 79
- Management Card 79
- Assigning a Name 85
- Resetting the Management Card 96
- Viewing the Event Log 98
- Viewing the Activity Monitor 104
- Configuring the Syslog Client 105
- Converteon 115
- Terminal Configuration Menu 119
- Data Rate (baud rate) 119
- Pinging Network Devices 125
- Converter Line Cards 127
- Module 4 - Port A 140
- Port Configurations 140
- OAM Configurations 140
- Port Management Menu 140
- Setting the Operating Mode 145
- Max Frame Size Config Menu 150
- Module 14 150
- Max Frame Size: 1632 150
- Setting the Auto-copy Feature 151
- Displaying Port Statistics 160
- Remote Peer Management 173
- Naming a Remote 179
- Line Card 179
- Displaying the 184
- Configuration 184
- Configuring 184
- Remote Ports 184
- Saving the 186
- Parameter 186
- Settings 186
- Chapter 7 191
- AT-CV5000 193
- TDM Management Menu 194
- Module 15, Port C 194
- TDM Port Configurations 194
- UART Configurations 194
- UART Configuration Menu 195
- > UART Local Console Mode 195
- UART Back Plane Mode 195
- Configuring the Operations 203
- Configuring an OAM Client 204
- OAM port is disconnected 210
- OAM is not in active mode 210
- Displaying OAM Statistics 223
- Dying Gasp 229
- Testing the Feature 235
- Configuring SNMPv3 237
- SNMPv3 Overview 238
- SNMPv3 Storage 241
- SNMPv3 Message 241
- Notification 241
- SNMPV3 Auth Table 242
- SNMPv3 User Table 242
- SNMPv3 View Table 242
- SNMPv3 Access Table 242
- SNMPv3 Group Table 245
- SNMPv3 Notify Table 245
- SNMPv3 Target Address Table 245
- Configuring SNMPv3 Entities 247
- Chapter 11 271
- Overview 272
- Configuring the TFTP Client 273
- TFTP Server IP Address-> _ 284
- Software Programs 287
- SNMPv3 Configuration Examples 291
- Configure SNMPv3 Access Table 292
- Configure SNMPv3 Group Table 292
- Operator 293
- Worksheet 294
- Numerics 317
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S99
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 MIB COMPILER Manual de usuario
(13 paginas)
(13 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 INSTALLATION Manual de usuario
(29 paginas)
(29 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 VLAN MANAGER Manual de usuario
(72 paginas)
(72 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 DEVICE MANAGEMENT Manual de usuario
(130 paginas)
(130 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 QoS MANAGER Manual de usuario
(146 paginas)
(146 paginas)
Hardware De La Computadora Allied-telesis AlliedView-EMS 3.11 DEVICE MANAGEMENT Manual de usuario
(402 paginas)
(402 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales