Allied-telesis AT-S63 Manual de usuario Pagina 302
- Pagina / 456
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 19: Spanning Tree and Rapid Spanning Tree Protocols
302 Section IV: Spanning Tree Protocols
Enabling or Disabling a Spanning Tree Protocol
To enable or disable spanning tree on the switch, perform the following
procedure:
1. From the Home page, select Configuration.
The System page is displayed with the General tab selected by
default, as shown in Figure 5 on page 38.
2. From the Configuration menu, select the Layer 2 option.
The Layer 2 page is displayed with the MAC Address tab selected by
default, as shown in Figure 123.
Figure 123. MAC Address Tab (Configuration)
3. Select the Spanning Tree tab.
- Web Browser Interface 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 18
- Document Conventions 19
- Contacting Allied Telesyn 21
- Switch’s IP Address 28
- Web Browser Tools 31
- Saving Your Parameter Changes 32
- AT-9424Ti/SP Series Switches 34
- Basic Switch Parameters 37
- Displaying System Information 42
- Rebooting a Switch 46
- Pinging a Remote System 50
- Enhanced Stacking 55
- Chapter 3: Enhanced Stacking 56
- Chapter 4: SNMPv1 and SNMPv2c 64
- Configuring Port Parameters 78
- Chapter 5: Port Parameters 82
- Multicast Rate Limiting 88
- Multicast Rate 88
- Displaying Port Statistics 89
- Chapter 6: MAC Address Table 100
- Creating a Static Port Trunk 104
- Chapter 7: Static Port Trunks 106
- Displaying the Port Trunks 110
- Creating a Port Mirror 114
- Section I: Basic Features 115 115
- Modifying a Port Mirror 117
- Disabling a Port Mirror 118
- Deleting a Port Mirror 119
- Displaying the Port Mirror 120
- Section I: Basic Features 121 121
- Advanced Operations 123
- File System 125
- Chapter 9: File System 126
- Figure 38 129
- Figure 38. List Files Page 129
- Downloading a File 134
- Uploading a File 139
- Event Logs and Syslog Servers 141
- Working with the Event Logs 142
- Clearing an 150
- Event Log 150
- Saving an Event 150
- Log to a File 150
- Working with Log Outputs 152
- Viewing a Log 154
- Output Definition 154
- Modifying a Log 156
- Deleting a Log 158
- Classifiers 159
- Configuring a Classifier 160
- Chapter 12: Classifiers 162
- Modifying a Classifier 166
- Deleting a Classifier 168
- Displaying the Classifiers 169
- Class of Service 181
- Configuring CoS 182
- Chapter 14: Class of Service 184
- Configuring Egress Scheduling 186
- Displaying the CoS Settings 188
- Displaying the QoS Schedule 190
- Quality of Service 191
- Managing Flow Groups 192
- Modifying a Flow 194
- Deleting a Flow 195
- Displaying Flow 195
- Managing Traffic Classes 198
- Modifying a 200
- Traffic Class 200
- Deleting a Traffic 202
- Displaying the 202
- Traffic Classes 202
- Flow Group List 205
- 5. Click Close 205
- Managing Policies 206
- Displaying 210
- Policies 210
- Denial of Service Defense 213
- Displaying the DoS Settings 217
- IGMP Snooping 219
- Configuring IGMP Snooping 220
- Chapter 17: IGMP Snooping 222
- 230 Section III: SNMPv3 230
- Section III: SNMPv3 233 233
- Section III: SNMPv3 235 235
- Section III: SNMPv3 237 237
- Deleting a User 239
- Table Entry 239
- Modifying a User 240
- Section III: SNMPv3 241 241
- Section III: SNMPv3 243 243
- Section III: SNMPv3 245 245
- Deleting a View 247
- Modifying a View 247
- 1.3.6.1.2.1.2.2.1.0.3 248
- Section III: SNMPv3 249 249
- Creating an 250
- Access Table 250
- Chapter 18: SNMPv3 252
- 252 Section III: SNMPv3 252
- Modifying an 254
- Section III: SNMPv3 255 255
- Creating a 257
- SecurityToGroup 257
- 258 Section III: SNMPv3 258
- 260 Section III: SNMPv3 260
- 262 Section III: SNMPv3 262
- 264 Section III: SNMPv3 264
- Notify Table 266
- Section III: SNMPv3 267 267
- Section III: SNMPv3 269 269
- 270 Section III: SNMPv3 270
- Modifying Target 272
- Address Table 272
- Section III: SNMPv3 273 273
- Creating a Target 275
- Parameters Table 275
- 276 Section III: SNMPv3 276
- Deleting a Target 278
- Section III: SNMPv3 281 281
- Section III: SNMPv3 283 283
- Section III: SNMPv3 285 285
- Section III: SNMPv3 287 287
- Section III: SNMPv3 289 289
- Displaying View 290
- Table Entries 290
- Displaying Access 291
- Displaying Notify 293
- Displaying Target 294
- Community 296
- Section III: SNMPv3 297 297
- Spanning Tree Protocols 299
- Protocols 301
- Configuring STP 304
- STP Settings 308
- Resetting STP to 311
- Settings 311
- Configuring RSTP 312
- Resetting RSTP 316
- Displaying RSTP 316
- Chapter 20 319
- Enabling MSTP 320
- Configuring MSTP 322
- Configuring the 325
- CIST Priority 325
- Deleting an MSTI 327
- Adding a VLAN 330
- Association 330
- Removing a 330
- 10 Mbps 20,000 336
- 100 Mbps 20,000 336
- 1000 Mbps 2,000 336
- Virtual LANs 343
- 344 Section V: VLANs 344
- 346 Secton V: Virtual LANs 346
- 348 Secton V: Virtual LANs 348
- Modifying a VLAN 350
- Secton V: Virtual LANs 351 351
- Selecting a VLAN Mode 353
- 354 Secton V: Virtual LANs 354
- 356 Secton V: Virtual LANs 356
- 358 Secton V: Virtual LANs 358
- Configuring GVRP 360
- Section V: Virtual LANs 361 361
- Section V: Virtual LANs 363 363
- Section V: Virtual LANs 365 365
- Table 12 367
- 368 Section V: Virtual LANs 368
- Displaying the GVRP Counters 370
- Section V: Virtual LANs 371 371
- Section V: Virtual LANs 373 373
- Protected Ports VLANs 375
- 376 Section V: Virtual LANs 376
- 378 Section V: Virtual LANs 378
- 380 Section V: Virtual LANs 380
- 382 Section V: Virtual LANs 382
- 384 Section V: Virtual LANs 384
- 386 Section V: Virtual LANs 386
- 388 Section V: Virtual LANs 388
- 390 Section VI: Port Security 390
- Configuring Port Security 392
- Section VI: Port Security 393 393
- Section VI: Port Security 395 395
- Chapter 25 397
- Setting Port Roles 398
- Section VI: Port Security 399 399
- 400 Section VI: Port Security 400
- 402 Section VI: Port Security 402
- 404 Section VI: Port Security 404
- 406 Section VI: Port Security 406
- Port Settings 408
- Section VI: Port Security 409 409
- 410 Section VI: Port Security 410
- Accounting 412
- Section VI: Port Security 413 413
- Management Security 415
- Encryption Keys, PKI, and SSL 417
- Displaying the SSL Settings 423
- Secure Shell (SSH) 425
- Configuring SSH 426
- Displaying the SSH Settings 428
- TACACS+ and RADIUS Protocols 431
- Configuring TACACS+ 434
- Configuring RADIUS 438
- Chapter 29 443
- Creating an ACE 446
- Deleting an ACE 448
- Interface 450
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S63
(119 paginas)
(40 paginas)
(38 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales