Allied-telesis AT-S63 Manual de usuario Pagina 143
- Pagina / 456
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-S63 Management Software Web Browser Interface User’s Guide
Section II: Advanced Operations 143
The Event log tab is shown in Figure 40.
Figure 40. Event Log Tab (Configuration)
3. In the Log Settings section, for the Status, click Enabled to enable the
event logs, or Disabled to disable the event logs.
The event log feature is enabled by default.
4. Click Apply to activate the settings on the switch.
If you enabled the logs, the switch immediately begins to add events to
the logs and send events to defined syslog servers.
5. Select the General tab.
- Web Browser Interface 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 18
- Document Conventions 19
- Contacting Allied Telesyn 21
- Switch’s IP Address 28
- Web Browser Tools 31
- Saving Your Parameter Changes 32
- AT-9424Ti/SP Series Switches 34
- Basic Switch Parameters 37
- Displaying System Information 42
- Rebooting a Switch 46
- Pinging a Remote System 50
- Enhanced Stacking 55
- Chapter 3: Enhanced Stacking 56
- Chapter 4: SNMPv1 and SNMPv2c 64
- Configuring Port Parameters 78
- Chapter 5: Port Parameters 82
- Multicast Rate Limiting 88
- Multicast Rate 88
- Displaying Port Statistics 89
- Chapter 6: MAC Address Table 100
- Creating a Static Port Trunk 104
- Chapter 7: Static Port Trunks 106
- Displaying the Port Trunks 110
- Creating a Port Mirror 114
- Section I: Basic Features 115 115
- Modifying a Port Mirror 117
- Disabling a Port Mirror 118
- Deleting a Port Mirror 119
- Displaying the Port Mirror 120
- Section I: Basic Features 121 121
- Advanced Operations 123
- File System 125
- Chapter 9: File System 126
- Figure 38 129
- Figure 38. List Files Page 129
- Downloading a File 134
- Uploading a File 139
- Event Logs and Syslog Servers 141
- Working with the Event Logs 142
- Clearing an 150
- Event Log 150
- Saving an Event 150
- Log to a File 150
- Working with Log Outputs 152
- Viewing a Log 154
- Output Definition 154
- Modifying a Log 156
- Deleting a Log 158
- Classifiers 159
- Configuring a Classifier 160
- Chapter 12: Classifiers 162
- Modifying a Classifier 166
- Deleting a Classifier 168
- Displaying the Classifiers 169
- Class of Service 181
- Configuring CoS 182
- Chapter 14: Class of Service 184
- Configuring Egress Scheduling 186
- Displaying the CoS Settings 188
- Displaying the QoS Schedule 190
- Quality of Service 191
- Managing Flow Groups 192
- Modifying a Flow 194
- Deleting a Flow 195
- Displaying Flow 195
- Managing Traffic Classes 198
- Modifying a 200
- Traffic Class 200
- Deleting a Traffic 202
- Displaying the 202
- Traffic Classes 202
- Flow Group List 205
- 5. Click Close 205
- Managing Policies 206
- Displaying 210
- Policies 210
- Denial of Service Defense 213
- Displaying the DoS Settings 217
- IGMP Snooping 219
- Configuring IGMP Snooping 220
- Chapter 17: IGMP Snooping 222
- 230 Section III: SNMPv3 230
- Section III: SNMPv3 233 233
- Section III: SNMPv3 235 235
- Section III: SNMPv3 237 237
- Deleting a User 239
- Table Entry 239
- Modifying a User 240
- Section III: SNMPv3 241 241
- Section III: SNMPv3 243 243
- Section III: SNMPv3 245 245
- Deleting a View 247
- Modifying a View 247
- 1.3.6.1.2.1.2.2.1.0.3 248
- Section III: SNMPv3 249 249
- Creating an 250
- Access Table 250
- Chapter 18: SNMPv3 252
- 252 Section III: SNMPv3 252
- Modifying an 254
- Section III: SNMPv3 255 255
- Creating a 257
- SecurityToGroup 257
- 258 Section III: SNMPv3 258
- 260 Section III: SNMPv3 260
- 262 Section III: SNMPv3 262
- 264 Section III: SNMPv3 264
- Notify Table 266
- Section III: SNMPv3 267 267
- Section III: SNMPv3 269 269
- 270 Section III: SNMPv3 270
- Modifying Target 272
- Address Table 272
- Section III: SNMPv3 273 273
- Creating a Target 275
- Parameters Table 275
- 276 Section III: SNMPv3 276
- Deleting a Target 278
- Section III: SNMPv3 281 281
- Section III: SNMPv3 283 283
- Section III: SNMPv3 285 285
- Section III: SNMPv3 287 287
- Section III: SNMPv3 289 289
- Displaying View 290
- Table Entries 290
- Displaying Access 291
- Displaying Notify 293
- Displaying Target 294
- Community 296
- Section III: SNMPv3 297 297
- Spanning Tree Protocols 299
- Protocols 301
- Configuring STP 304
- STP Settings 308
- Resetting STP to 311
- Settings 311
- Configuring RSTP 312
- Resetting RSTP 316
- Displaying RSTP 316
- Chapter 20 319
- Enabling MSTP 320
- Configuring MSTP 322
- Configuring the 325
- CIST Priority 325
- Deleting an MSTI 327
- Adding a VLAN 330
- Association 330
- Removing a 330
- 10 Mbps 20,000 336
- 100 Mbps 20,000 336
- 1000 Mbps 2,000 336
- Virtual LANs 343
- 344 Section V: VLANs 344
- 346 Secton V: Virtual LANs 346
- 348 Secton V: Virtual LANs 348
- Modifying a VLAN 350
- Secton V: Virtual LANs 351 351
- Selecting a VLAN Mode 353
- 354 Secton V: Virtual LANs 354
- 356 Secton V: Virtual LANs 356
- 358 Secton V: Virtual LANs 358
- Configuring GVRP 360
- Section V: Virtual LANs 361 361
- Section V: Virtual LANs 363 363
- Section V: Virtual LANs 365 365
- Table 12 367
- 368 Section V: Virtual LANs 368
- Displaying the GVRP Counters 370
- Section V: Virtual LANs 371 371
- Section V: Virtual LANs 373 373
- Protected Ports VLANs 375
- 376 Section V: Virtual LANs 376
- 378 Section V: Virtual LANs 378
- 380 Section V: Virtual LANs 380
- 382 Section V: Virtual LANs 382
- 384 Section V: Virtual LANs 384
- 386 Section V: Virtual LANs 386
- 388 Section V: Virtual LANs 388
- 390 Section VI: Port Security 390
- Configuring Port Security 392
- Section VI: Port Security 393 393
- Section VI: Port Security 395 395
- Chapter 25 397
- Setting Port Roles 398
- Section VI: Port Security 399 399
- 400 Section VI: Port Security 400
- 402 Section VI: Port Security 402
- 404 Section VI: Port Security 404
- 406 Section VI: Port Security 406
- Port Settings 408
- Section VI: Port Security 409 409
- 410 Section VI: Port Security 410
- Accounting 412
- Section VI: Port Security 413 413
- Management Security 415
- Encryption Keys, PKI, and SSL 417
- Displaying the SSL Settings 423
- Secure Shell (SSH) 425
- Configuring SSH 426
- Displaying the SSH Settings 428
- TACACS+ and RADIUS Protocols 431
- Configuring TACACS+ 434
- Configuring RADIUS 438
- Chapter 29 443
- Creating an ACE 446
- Deleting an ACE 448
- Interface 450
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S63
(119 paginas)
(40 paginas)
(38 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales