Allied-telesis AT-9000 Series Manual de usuario Pagina 191
- Pagina / 258
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AlliedWare Plus Version 2.1.8 Management Software Web Interface User’s Guide
191
exchange with a client. The range is 1
to 65,535 seconds. The default value is
60 seconds.
Tx-period Sets the number of seconds an
authenticator port waits for a response
to an EAP-request/identity frame from
a client before retransmitting the
request. The default value is 30
seconds. The range is 1 to 65,535
seconds.
Reauth-period Specifies the time interval that an
authenticator port requires a client to
reauthenticate. The range is 1 to
65,535 seconds. The default value is
3600 seconds.
Supplicant-timeout Sets the timer used by the switch to
determine authentication server
timeout conditions. The range is 1 to
65,535 seconds. The default value is
30 seconds.
Server-timeout Sets the timer used by the switch to
determine authentication server
timeout conditions. The range is 1 to
65,535 seconds. The default value is
30 seconds.
Re-authentication— Activates reauthentication on the
authenticator port. The client must periodically reauthenticate
according to the time interval set with the Reauth-period timer.
Click the box to activate this field.
Number of Re-auth Requests— Specifies the maximum number
of times the switch retransmits EAP Request packets to a client
before it times out an authentication session. The range is 1 to 10
retransmissions. The default value is 2.
Port Control Direction— Specifies whether authenticator ports
that are in the unauthorized state should forward egress broadcast
and multicast traffic. Choose from the following:
In Specifies that authenticator ports in the
unauthorized state should forward egress
broadcast and multicast traffic, and discard the
ingress broadcast and multicast traffic. This is
the default setting.
- AT-9000 Series 1
- Copyright 2
- Contents 5
- Document Conventions 12
- Contacting Allied Telesis 14
- Browser Interface 15
- Management Sessions 16
- Web Manager Accounts 17
- Starting a Management Session 19
- Figure 3. Login Page 22
- What to Configure First 27
- Saving Your Changes 28
- 5 on page 28 29
- Basic Switch Parameters 31
- Setting System 33
- Time Manually 33
- Setting an SNTP 34
- Setting a Remote Log Server 39
- Displaying and 42
- Setting the Active 42
- Uploading a 43
- Managing User Accounts 44
- Changing a User 45
- Password 45
- Changing the 47
- User Privilege 47
- Rebooting a Switch 49
- Upgrading the Software 50
- Displaying System Information 53
- Setting Port Parameters 57
- Changing the Port Settings 62
- 7. Click Apply 65
- 8. Click SAVE 65
- Setting Port Statistics 71
- Displaying Port Statistics 72
- Receive Statistics 73
- Transmit 75
- Statistics 75
- Interface 77
- Clearing Port Statistics 79
- Setting Port Mirroring 81
- Assigning a Destination Port 85
- Specifying Direction Type 86
- Chapter 7 89
- Setting the MAC Address 95
- Displaying the MAC Address 96
- Multicast MAC 97
- Addresses 97
- Assigning a MAC Address 98
- Multicast 99
- Deleting a MAC Address 101
- Setting LACP 103
- Overview 104
- Displaying LACP Trunks 105
- Chapter 9: Setting LACP 106
- Modifying an LACP Trunk 109
- Adding Static Trunks 117
- Deleting Static Trunks 123
- Chapter 11 125
- Tagged and 127
- Untagged Ports 127
- Displaying VLANs 128
- Adding a VLAN 130
- Modifying VLANs 132
- Assigning a Native VLAN 134
- 7. Click SAVE 135
- Deleting VLANs 136
- Protocol (IGMP) Snooping 137
- Clearing the Routers List 141
- 5. Click Apply 142
- 6. Click SAVE 142
- Disabling IGMP Snooping 143
- Displaying the Routers List 144
- Displaying the Hosts List 145
- Chapter 13 147
- Power Over Ethernet (PoE) 155
- Prioritization 157
- Displaying PoE Settings 158
- PoE Configuration 160
- Security 163
- Interface— Port number 166
- Chapter 16 171
- Server 1 174
- Configuring 175
- Remote Manager 175
- Authentication 175
- Using RADIUS 175
- Adding a 177
- RADIUS Server 177
- Using TACACS+ 179
- Chapter 17 185
- Chapter 18 197
- IP Management 199
- Guidelines 199
- Assigning an IPv4 Address 200
- Assigning a 201
- DHCP IPv4 201
- Assigning an IPv6 Address 204
- Displaying IP Addresses 206
- Modifying IP Addresses 207
- Modifying an 208
- IPv6 Address 208
- Setting LLDP and LLDP-MED 209
- Setting LLDP Locations 211
- Figure 74. Locations Tab 212
- 5. Click Add 214
- Creating a 215
- Coordinate 215
- Location 215
- Creating an 217
- ELIN Location 217
- Configuring LLDP and LLDP-MED 219
- Setting LLDP 220
- Port Assignments 220
- Assigning Port 222
- Locations 222
- Enabling LLDP 224
- Displaying LLDP 231
- Neighbor 231
- Information 231
- Neighbor Detail 232
- Displaying LLDP Statistics 236
- Displaying LLDP Locations 238
- Displaying 239
- Displaying ELIN 240
- Displaying the 241
- Basic LLDP 241
- Configuration 241
- Displaying Port 243
- LLDP-MED TLV 245
- Disabling LLDP on the Switch 247
- Setting sFlow 249
- Configuring sFlow on a Port 252
- Chapter 20: Setting sFlow 254
- Enabling sFlow on the Switch 256
- Displaying the sFlow Settings 257
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-9000 Series
Hardware De La Computadora Allied-telesis AlliedWare Plus Operating System Version 5.4.4C (x Manual de usuario
(222 paginas)
(222 paginas)
Hardware De La Computadora Allied-telesis AT-S95 CLI (AT-8000GS Series) Manual de usuario
(397 paginas)
(397 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales