Allied-telesis AT-CV1203 Manual de usuario

613-001163 Rev. ACONVERTEON™ FamilyTwo-Slot ChassisAT-CV1203Installation Guide

Tables10

11PrefaceThis guide contains the installation instructions for the Converteon AT-CV1203 Chassis. This preface contains the following sections: “Safet

Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-CV1203 Chassis Installation Guide13Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are available in

Preface14Contacting Allied TelesisThis section provides Allied Telesis contact information for technical support as well as sales and corporate inform

15Chapter 1OverviewThis chapter contains the following sections: “Features” on page 16 “Front and Back Panels” on page 17 “AT-CVMNT12 Wall-Mount Br

Chapter 1: Overview16FeaturesThe AT-CV1203 Chassis is part of the Converteon product line. It is a two-slot enclosure for the Fast and Gigabit Etherne

AT-CV1203 Chassis Installation Guide17Front and Back PanelsFigure 2 shows the front and back panels of the AT-CV1203 Chassis.Figure 2. Front and Back

Chapter 1: Overview18AT-CVMNT12 Wall-Mount BracketThe AT-CV1203 Chassis can be mounted on a wall with the optional AT-CVMNT12 Wall-Mount Bracket, show

AT-CV1203 Chassis Installation Guide19LEDsFigure 4 identifies the power LEDs on the rear panel.Figure 4. Power LEDsTable 1 describes the power LEDs.Ta

Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Overview20Operations, Administration and Maintenance FeaturesThe AT-CV1203 Chassis supports all the Operations, Administration and Maintena

21Chapter 2InstallationThis chapter contains the following installation procedures for the AT-CV1203 Chassis: “Reviewing the Safety Precautions” on p

Chapter 2: Installation22Reviewing the Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis or any

AT-CV1203 Chassis Installation Guide23Selecting a Site for the ChassisThe site chosen for the unit should meet the following requirements: The power

Chapter 2: Installation24Unpacking the ChassisAs you unpack the unit, verify that all the items listed in Table 2 are included in the shipping contain

AT-CV1203 Chassis Installation Guide25Two pre-installed AT-CV5PNL1 slot coversFour rubber feetOne grounding lugTwo tie wrapsTable 2. AT-CV1203 Chassis

Chapter 2: Installation26Installing the Rubber FeetIf you are installing the AT-CV1203 Chassis on a desktop, turn the unit over and attach the four ru

AT-CV1203 Chassis Installation Guide27Installing a Converteon Line CardTo install a Converteon media converter line card or the AT-CV5M02 Management C

Chapter 2: Installation28NoteEmpty slots should be kept covered. Retain the slot cover and reinstall it if you ever remove the line card without repla

AT-CV1203 Chassis Installation Guide29Figure 8. Inserting a Line Card6. Use a Phillips screwdriver to tighten the captive screw on the line card, as s

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-

Chapter 2: Installation30Grounding the ChassisThis procedure requires these items: Phillips head No. 2 screwdriver 10 AWG solid wire (The length of

AT-CV1203 Chassis Installation Guide313. Remove the two grounding lug screws from the back panel of the chassis.Figure 12. Removing the Grounding Lug

Chapter 2: Installation32Powering On the ChassisNoteUse only power sources that are UL Listed (QQGQ or EPBU), TUV Licensed or other Safety Agencies ap

AT-CV1203 Chassis Installation Guide33Figure 15. Connecting the Power Cord3. To prevent accidentally disconnecting the power cord from the chassis, se

Chapter 2: Installation344. Connect the power cord to an appropriate power source. For the power requirements, refer to “Power Specifications” on page

AT-CV1203 Chassis Installation Guide35Verifying the InstallationAfter powering on the chassis, view the PWR GOOD LED. The LED should be ON. The PWR A

Chapter 2: Installation36Replacing a Line Card or the Management CardAll the Converteon media converter line cards and the AT-CV5M02 Management Card s

37Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: 5.40 cm x 13.12 cm x 15.52 cm(2.12 in x 5.17 in x 6.11 in)(H x W x L):Weight: 0

Appendix A: Technical Specifications38Safety and Electromagnetic Emissions CertificationsEMI: FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CEIm

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled Translated Sa

5Preface ...

Contents6

7Figure 1. AT-CV1203 Chassis ...

Figures8

9Table 1. Safety Symbols ..............................