Allied-telesis Removable Power Supply and Fan Manual de usuario

Installation GuideRemovable Power Supply and FanAT-PWR01AT-PWR02AT-PWR05AT-FAN01AT-FAN03

Installation Guide9Connecting an AC power supplyFollow these instructions to connect an AT-PWR01, AT-PWR02, or AT-PWR05 AC PSU to an AC power supply:W

Removable Power Supply and Fan10Warning When SBx908 devices are connected with VCS stacking cables (either HS-STK-CBL or XEM-STK-CBL), each individual

Installation Guide11Connecting a PWR01 or PWR021. Plug the supplied AC power cord into the power inlet on the PSU and attach the retaining clip.2. Con

Removable Power Supply and Fan122. Plug the AC power cord into the power inlet on the PSU.3. Connect the power cord to the main power source.4. Check

Installation Guide13Connecting a PWR01 DC power supplyFollow these instructions to connect an AT-PWR01 DC PSU to a DC power supply. Only trained and q

Removable Power Supply and Fan14• AT-PWR01 DC is grounded at the GND terminal. In order to avoid large circulating ground currents, the wires of ea

Installation Guide1511. Confirm that the switch is receiving power.Check that at least one of the PSU LEDs on the front panel of the switch is lit gre

Removable Power Supply and Fan16Connecting a PWR05 DC power supplyFollow these instructions to connect an AT-PWR05 DC PSU to a DC power supply. Only t

Installation Guide171. Ensure that the circuit breaker for the supply circuit and the Run/Standby switch on the PSU are off (slide to position O). 2.

Removable Power Supply and Fan18Checking LEDsLEDs on PSUs, fans, and the front panels of switches indicate the operational status of the devices. Afte

Removable Power Supply and FanInstallation GuideAT-PWR01AT-PWR02AT-PWR05AT-FAN01AT-FAN03Download the complete document set fromwww.alliedtelesis.com/s

Installation Guide19PWR05ACThe following table describes LEDs on the PWR05 AC power supply unit.PWR05DCThe following table describes LEDs on the PWR05

Removable Power Supply and Fan20Switch The following table describes how LEDs on the switch report operations and faults with installed PSUs and FOMs.

Installation Guide21Removing a Power Supply Unit or FanFollow these instructions to remove a PSU, chassis fan module, FOM or blanking plate.Before you

Removable Power Supply and Fan22The following is a diagram of PWR05 and FAN03 3. Remove the PSU, chassis fan module, FOM or the blanking plate from t

Installation Guide23Avoid the spinning blades on FAN03. Contact may cause personal injury or damage the unit. Do not operate the switch for extended p

Removable Power Supply and Fan24TroubleshootingIf the PSU does not function as expected: Check that all cable connections are correct and secure. On

Installation Guide25Obtaining Documentation and ResourcesThe complete document set for x900 Series switches and SwitchBlade x908 includes: this Insta

Removable Power Supply and Fan26AT-TFTP Server for Windows is a TFTP (Trivial File Transfer Protocol) server for transferring software versions, confi

Installation Guide27StandardsWhere applicable, the products in this document meet the following standards:Category Approval Agency and Requirement S

Removable Power Supply and Fan28EC Declaration of ConformityWe: ALLIED TELESIS LABS LIMITED27 NAZARETH AVENUECHRISTCHURCH 8024NEW ZEALANDDeclare under

Removable Power Supply and Fan2Removable Power Supply and Fan Installation GuideDocument Number C613-04057-00 REV P© 2008 Allied Telesis, Inc. All rig

Installation Guide3ContentsAbout this Guide ...

Removable Power Supply and Fan4About this GuideThis Installation Guide describes how to install the following PSUs and fans: AT-PWR01 PSU, either AC

Installation Guide5Package ContentsDepending on the model, switches are shipped with a single supply unit (PSU), either AC or DC. Some models also hav

Removable Power Supply and Fan6Installing a Power Supply Unit or FanUse these instructions to install PSUs, chassis fan modules and FOMs. Do not comb

Installation Guide7Installing a PWR01, PWR02, or FAN011. If there is a PSU, fan or blanking plate in the bay you wish to install the unit, first remov

Removable Power Supply and Fan8Installing a PWR05 or FAN031. If there is a PSU, fan or blanking plate in the bay you wish to install the unit, first r