Allied-telesis AT-CV1000 Manual de usuario

613-000810 Rev. ACONVERTEON™ FamilyOne-Slot ChassisAT-CV1000Installation Guide

Preface10Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-CV1000 One-Slot Chassis Installation Guide11Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are avai

Preface12Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate infor

13Chapter 2OverviewThis chapter contains the following sections: “Features” on page 14 “Converteon™ Line Cards” on page 16 “Blank Slot Cover” on pa

Chapter 2: Overview14FeaturesThe AT-CV1000 One-Slot Converteon™ chassis, as shown in Figure 1, is designed to house any single Converteon™ line card.

AT-CV1000 One-Slot Chassis Installation Guide15Figure 2 shows the front and back panels of the AT-CV1000 chassis. Figure 2. AT-CV1000 Chassis Front an

Chapter 2: Overview16Converteon™ Line CardsThe AT-CV1000 chassis can only house one Converteon™ line card. The line card is hot swappable.NoteFor a cu

AT-CV1000 One-Slot Chassis Installation Guide17Blank Slot CoverThe AT-CV5PNL1 blank slot cover is designed to maintain optimal, trouble-free environme

Chapter 2: Overview18Power AdapterThe AT-CV1000 chassis uses a two-part AC power adapter (supplied), as shown in Figure 4.Figure 4. AC Power Adapter51

AT-CV1000 One-Slot Chassis Installation Guide19Network TopologiesThis section describes two network topologies you can create with the Converteon™ Fas

Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 2: Overview20Back-to-BackTopologyFigure 6 illustrates a back-to-back topology using two AT-CV1000 chassis, each with an AT-CM202 line card ins

21Chapter 3InstallationThis chapter contains the following installation procedures for the AT-CV1000 chassis: “Reviewing Safety Precautions” on page

Chapter 3: Installation22Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis or any of

AT-CV1000 One-Slot Chassis Installation Guide23Selecting a Site for the ChassisObserve the following requirements when choosing a site for the chassis

Chapter 3: Installation24Unpacking the ChassisTo unpack the chassis, perform the following procedure:1. Remove all components from the shipping packag

AT-CV1000 One-Slot Chassis Installation Guide25Using the AT-CV1000 Chassis on a DesktopTo use the AT-CV1000 chassis on a desktop, perform the followin

Chapter 3: Installation26Mounting the AT-CV1000 Chassis on a WallThe AT-CV1000 chassis is shipped with two wall-mounting brackets. The chassis is desi

AT-CV1000 One-Slot Chassis Installation Guide276. Install two plastic anchors and two screws onto the wall, as illustrated in Figure 9.Figure 9. Insta

Chapter 3: Installation28Installing an AT-CV1000 Chassis in an AT-MCR12 Rack-Mount ChassisIn order to install the AT-CV1000 chassis in an AT-MCR12 rac

AT-CV1000 One-Slot Chassis Installation Guide29the AT-CV1000 chassis and loosen the captive screw to remove the mounting rail from that slot, as shown

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-

Chapter 3: Installation304. Turn the chassis over, as shown Figure 14.Figure 14. AT-CV1000 Chassis with AT-CVMCR Adapter Installed5. Use the thumb tab

AT-CV1000 One-Slot Chassis Installation Guide317. Tighten the captive screw on the AT-CVMCR adapter to secure the AT-CV1000 in the chassis, as shown i

Chapter 3: Installation32Installing a Converteon™ Line CardTo install a Converteon™ line card, perform the following procedure:1. Remove the Converteo

AT-CV1000 One-Slot Chassis Installation Guide334. Locate the alignment guides on both sides of the slot, as shown in Figure 17.Figure 17. Location of

Chapter 3: Installation347. Use a Phillips screwdriver to tighten the captive screw on the line card, as shown in Figure 19.Figure 19. Tightening the

AT-CV1000 One-Slot Chassis Installation Guide35Powering On an AT-CV1000 ChassisThe AC power adapter for the AT-CV1000 chassis consists of two parts: a

Chapter 3: Installation36The chassis is now ready for network operations.Warning: Power cord is used as a disconnection device. To de-energize equipme

AT-CV1000 One-Slot Chassis Installation Guide37Installing a Blank Slot CoverThe AT-CV1000 chassis is shipped with the line card slot covered with the

Chapter 3: Installation386. Use a Phillips screwdriver to tighten the captive screw, as shown in Figure 22.Figure 22. Tightening the Captive Screw on

AT-CV1000 One-Slot Chassis Installation Guide39Warranty Registration

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

Chapter 3: Installation40Warranty RegistrationAllied Telesis hardware products are covered under limited warranties. Some products have a longer warra

41Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: W x D x H10.48 cm x 17.77 cm x 2.54 cm(4.125 in x 7.0 in x 1.0 in)Environmental

Appendix A: Technical Specifications42Safety and Electromagnetic Emissions CertificationsEMI: FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CEIm

5Preface ...

Contents6

7Figure 1. AT-CV1000 One-Slot Converteon™ Chassis...

Figures8

9PrefaceThis guide contains instructions on how to install an AT-CV1000 One-Slot Converteon™ chassis. This preface contains the following sections: “