Allied Telesis AT-CV10x Series Guía de instalación descargar pdf (Pagina 2)

The following table lists the line card status LEDs.

Features

The AT-CV10x Series line cards are designed to support Link Test,

MissingLink™ (ML), Smart MissingLink (SML), and Auto-MDI/MDIX features.

The DIP switches are used to set these features.

DIP Switches

The AT-CV10x Series line card features two DIP switches, Diagnostic Mode

DIP Switch 1 (Table 1) and Port Configuration DIP Switch 2 (Table 2), as

shown in Figure 2.

The tables below list the positions of these two DIP switches.

LED Color Description

RDY Green The line card has passed diagnostics.

OFF The line card has not passed diagnostics.

SML Green The Smart MissingLink mode is enabled.

OFF The Smart MissingLink mode is disabled.

ML Green The MissingLink mode is enabled.

OFF The MissingLink mode is disabled.

Table 1. Diagnostic Mode DIP Switch 1 Positions

Operating Mode DIP 1 DIP 2 DIP 3 DIP 4

Link Test (default) OFF OFF X X

Smart MissingLink (SML) OFF ON XX

MissingLink™ (ML) ON OFF X X

Manufacturing Settings OFF OFF OFF OFF

“X” means the DIP switch position could be either ON or OFF.

Table 2. Port Configuration DIP Switch 2 Positions

Operating Mode DIP 1 DIP 2 DIP 3 DIP 4

Auto MDI-X Enabled (default) X ON XX

Auto MDI-X Disabled X OFF X X

Manufacturing Settings OFF OFF OFF OFF

“X” means the DIP switch position could be either ON or OFF.

Installing an AT-CV10x Series Line Card

Note

The Converteon™ line cards can be installed in any of the line card slots

located on the front panel of the Converteon™ chassis.

To install an AT-CV10x Series line card, perform the following procedure:

Caution

Before installing an AT-CV10x Series line card, refer to the appropriate

Converteon™ Series Chassis Installation Guide for electrical safety and

emission information.

Caution

Be sure to observe all standard electrostatic discharge (ESD)

precautions, such as wearing an antistatic wrist strap, to avoid

damaging the device. A line card can be damaged by static electricity.

1. Remove the Converteon™ line card from its shipping package and store

the package in a safe place.

You must use the original package if you need to return the unit to Allied

Telesis.

2. Select an empty line card slot in the Converteon™ chassis for the card.

3. Remove the AT-CV5PNL1 blank slot cover from the selected slot.

Keep the blank slot cover in a safe area in case you remove the line card.

The blank slot cover is used to keep dust from getting into the chassis and

maintains proper airflow, cooling, and ventilation throughout the chassis.

4. Locate the alignment guides in the chassis slot.

5. Align the back edge of the line card with the alignment guides located

inside the slot. Avoid touching the line card components.

– For the AT-CV5000, align with the top and bottom alignment guides.

– For the AT-CV1000 and AT-CV1200, align with the left and right

alignment guides.

6. Slide the line card until the front of the card is flushed with the front of the

chassis.

7. Use a Phillips screwdriver to tighten the captive screw on the line card.

8. Repeat this procedure to install additional line cards.

Cabling an AT-CV10x Series Line Card

To connect the cables to an AT-CV10x Series line card, refer to the

Converteon™ Media Converter Line Cards Reference Guide for instructions.

Technical Specifications

Physical, Environmental, and Electrical Rating

Dimensions (H x W x L) .855" x 2.89" x 5.1"

(2.2 cm x 7.3 cm x 13.0cm)

Operating Temperature 0° C to 40° C (32° F to 104° F)

Storage Temperature -25° C to 70° C (-13° F to 158° F)

Operating Relative Humidity 5% to 90% RH (non-condensing)

Storage Relative Humidity 5% to 95% RH (non-condensing)

Operating Altitude Range Up to 3,048 m (10,000 ft)

MTBF (Telcordia Standards)

AT-CV101 1,020,00 hrs

AT-CV102 890,000 hrs

AT-CV102/1, AT-CV102/2 1,020,00 hrs

Power Consumption

AT-CV101, AT-CV102 3.0 watts

AT-CV102/1 2.5 watts

AT-CV102/2 5.0 watts

Optical Specifications

Connector Type Dual SC or Dual ST

Wavelength (nm) 1310 nm or 1510 nm

Fiber Type Single-mode or Multi-mode

Operating Distance (km) 2 km (1.24 miles) to 40 km (24.8 miles)

Optical Output Power (dBm)

AT-CV101, AT-CV102 -20 dBm to -14 dBm

AT-CV102/1 -15 dBm to -5 dBm

AT-CV102/2 -15 dBm to 0 dBm

Receiver Power Sensitivity (dBm)

AT-CV101, AT-CV102 -31 dBm to -11 dBm

AT-CV102/1, AT-CV102/2 -34 dBm to -3 dBm

Electrical Safety and Emission Statement

Standards: This product meets the following standards when installed in compliant host equipment.

Emission FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CE

WARNING: In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Immunity EN55024

Electrical Safety UL60950-1 (

), EN60950-1 (TUV), CAN/CSA C22.2 No. 60950-1

No part of this publication may be reproduced without prior written permission from Allied Telesis Inc.

U.S. Federal Communications Commission

RADIATED ENERGY

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant

to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with this instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right

to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur

du Canada.

4 5 6

1 2

*613-000296 Rev C* 1

Comentarios a estos manuales

Sin comentarios

Allied Telesis AT-CV10x Series Guía de instalación Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Convertidores de medios de la red Allied Telesis AT-CV10x Series