Allied-telesis AT-S39 Manual de usuario Pagina 110
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 12: Rapid Spanning Tree Protocol Commands
110
bridges connected to the port. If the port receives
STP BPDU packets in response, the port changes to
STP compatible mode. If the port receives RSTP
BPDU packets, it operates in RSTP.
Note
All changes to a port’s RSTP settings, with the exception of port cost,
are activated immediately. A change to the port cost value requires
you to reset the switch. A new port cost value is not implemented
until the unit is reset.
Description
This command sets a port’s RSTP settings.
Examples
The following command sets Port 4’s port cost to 1 000 000 and it’s port
priority to 224:
set rstp port=4 portcost=1000000 portpriority=14
The following command changes Ports 7 to 10 so they are not
considered as edge ports:
set rstp port=7-10 edgeport=no
The following command returns Port 11 to the default RSTP settings:
set rstp port=1 default
- Command Line 1
- User’s Guide 1
- 2003 Allied Telesyn, Inc 2
- Table of Contents 3
- Document Conventions 8
- AT-S39 User’s Guide 9
- Contacting Allied Telesyn 10
- Management Software Updates 11
- Starting a Command Line 12
- Management Session 12
- Starting a Management Session 13
- Key Features 14
- Command Formatting 15
- Basic Command Line Commands 16
- SAVE CONFIGURATION 17
- SET PROMPT 18
- CLEAR SCREEN 19
- SET SWITCH CONSOLEMODE 21
- LOGOFF and QUIT 22
- SHOW DHCPBOOTP 24
- ENABLE DHCPBOOTP 25
- DISABLE DHCPBOOTP 26
- SHOW IP ROUTE 30
- SET IP ROUTE 31
- RESET IP 32
- PURGE IP 33
- SHOW SYSTEM 34
- SET SYSTEM 35
- RESET SYSTEM 36
- SHOW SWITCH 37
- RESTART SWITCH 38
- RESTART REBOOT 39
- Enhanced Stacking Commands 42
- SET SWITCH STACKMODE 43
- SHOW REMOTELIST 44
- ACCESS SWITCH 45
- SNMP Community Strings and 48
- Trap Commands 48
- SHOW SNMP 49
- DESTROY SNMP COMMUNITY 50
- CREATE SNMP COMMUNITY 51
- SET SNMP COMMUNITY 52
- RESET SNMP 53
- ADD SNMP COMMUNITY TRAPHOST 54
- Management Security 56
- SET PASSWORD MANAGER 57
- SET PASSWORD OPERATOR 58
- SHOW HTTP SERVER 59
- DISABLE HTTP SERVER 61
- ENABLE SNMP 62
- DISABLE SNMP 63
- SET SWITCH CONSOLETIMER 64
- SHOW SWITCH PORT 66
- SET SWITCH PORT 67
- RESET SWITCH PORT 71
- SET SWITCH SECURITYMODE 73
- SET SWITCH THRESHOLD 75
- SHOW SWITCH THRESHOLD 76
- SHOW SWITCH TRUNK 78
- CREATE SWITCH TRUNK 79
- ADD SWITCH TRUNK 80
- DELETE SWITCH TRUNK 81
- DESTROY SWITCH TRUNK 82
- CREATE SWITCH MIRROR 84
- ADD SWITCH MIRROR 85
- DELETE SWITCH MIRROR 86
- SET SWITCH MIRROR 87
- DESTROY SWITCH MIRROR 88
- STP Commands 89
- ACTIVATE STP 91
- ENABLE STP 92
- DISABLE STP 93
- SET STP PORT 96
- RESET STP 98
- RSTP Commands 99
- SHOW RSTP 100
- ACTIVATE RSTP 101
- DISABLE RSTP 102
- ENABLE RSTP 103
- RESET RSTP 104
- SET RSTP 105
- SET RSTP PORT 108
- VLAN Commands 111
- SET SWITCH SWITCHMODE 112
- SET SWITCH VLANMODE 113
- SHOW VLAN 114
- CREATE VLAN 115
- Chapter 13: VLAN Commands 116
- DELETE VLAN 122
- RESET VLAN 126
- SET SWITCH VLANSTATUS 127
- SET SWITCH INFILTERING 128
- MAC Address Table Commands 129
- SHOW SWITCH FDB 130
- ADD SWITCH FDB 132
- DELETE SWITCH FDB 133
- SET SWITCH AGINGTIMER 134
- IGMP Snooping Commands 135
- SET IP IGMP 136
- SHOW IP IGMP 138
- Broadcast Frame Control 139
- SET SWITCH BROADCAST 140
- TACACS+ and RADIUS 142
- Commands 142
- DISABLE AUTHENTICATION 143
- ENABLE AUTHENTICATION 144
- RESET AUTHENTICATION 145
- SET AUTHENTICATION 146
- SHOW AUTHENTICATION 148
- ADD TACACSSERVER 149
- DELETE TACACSSERVER 150
- ADD RADIUSSERVER 151
- DELETE RADIUSSERVER 152
- ENABLE PORTACCESS 154
- DISABLE PORTACCESS 155
- SHOW PORTACCESS STATUS 156
- SET PORTACCESS 157
- Statistics Commands 160
- SHOW SWITCH COUNTER 161
- SHOW SWITCH PORT COUNTER 162
- RESET SWITCH COUNTER 163
- RESET SWITCH PORT COUNTER 164
- Download and Upload 165
- ENABLE TFTPSERVER 172
- DISABLE TFTPSERVER 173
- SHOW TFTPSERVER 174
- Command Reference 175
- Basic Switch Commands 177
- Chapter 21: Command Reference 178
- Port Parameter Commands 182
- Port Security Commands 183
- Port Trunking Commands 183
- Port Mirroring Commands 184
- TACACS+ and RADIUS Commands 190
- Download and Upload Commands 192
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S39
(164 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales