Allied-telesis AT-GS950/48PS Manual de usuario Pagina 103
- Pagina / 386
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-GS950/48PS Switch Web Interface User’s Guide
103
Disable a Port Trunk
This procedure explains how to disable a port trunk.
Caution
Before you disable or modify a port trunk, disconnect all of the
cables from the ports of the trunk. Leaving the cables connected
during the reconfiguration of a trunk can create loops in your
network topology. Loops can result in broadcast storms which can
severely limited the effective bandwidth of your network.
To disable a port trunk, perform the following procedure:
1. Disconnect all of the Ethernet cables from the ports of the trunk.
2. Select the Bridge folder.
The Bridge folder expands.
3. From the Bridge folder, select the Trunk Config folder.
The Trunk Config folder expands.
4. From the Trunk Config folder, select Trunking.
The Trunking Page is shown in Figure 31 on page 99.
5. To disable a port trunk, select Disable from the pull-down menu next
to the trunk that you want to disable.
6. Click Apply.
7. From the main menu on the left side of the page, select Save
Configuration to Flash to permanently save your changes.
8. Modify the port trunk configuration in the same way on the other
switch.
- AT-GS950/48PS 1
- Contents 10
- List of Figures 11
- List of Tables 15
- Document Conventions 18
- Getting Started 21
- Chapter 1 23
- Switch’s IP Address 24
- Web Browser Tools 27
- System Configuration 29
- System Management Information 30
- IP Access List Configuration 34
- Delete an IP 35
- Address List 35
- Add New User 36
- Name and 36
- Password 36
- Modify User 37
- Delete User Name 38
- User Interface Configuration 39
- User Interface 40
- System Time 41
- Setting Daylight 43
- Parameters 43
- SSL Settings 44
- 4. Click Apply 45
- DHCP Client Configuration 47
- DHCP Auto Configuration 49
- System Information Display 50
- System Log Configuration 52
- Bridge Configuration 55
- Port Configuration 57
- Chapter 3: Port Configuration 60
- STP and RSTP 63
- Bridge Priority 65
- Path Costs and Port Costs 66
- Port Priority 66
- Forwarding 67
- Delay and 67
- Topology 67
- Point-to-Point and Edge Ports 68
- Mixed STP and 69
- RSTP Networks 69
- Spanning Tree 70
- Chapter 4: STP and RSTP 72
- Configure RSTP Port Settings 75
- Configure the 77
- Advanced RSTP 77
- Spanning Tree Topology 80
- Chapter 5 81
- VLAN Mapping 88
- Modify MST 89
- Instance 89
- Delete MST 89
- Topology Information 92
- Static Port Trunking 95
- Create a Port Trunk 99
- Modify a Port Trunk 101
- Disable a Port Trunk 103
- LACP Port Trunks 105
- Overview 106
- System Priority 107
- Port Priority Value 108
- General Guidelines 109
- Chapter 7: LACP Port Trunks 110
- Group Status 111
- Configuration 112
- Port Priority Configuration 114
- Port Mirroring 115
- Port Mirroring Configuration 117
- Disable Port Mirroring 118
- Loopback Protection 119
- MAC Address Table 123
- Chapter 10: MAC Address Table 126
- Modify Static Unicast Address 128
- Delete Static Unicast Address 129
- IGMP Snooping 135
- IGMP Snooping Configuration 138
- Chapter 11: IGMP Snooping 140
- Storm Control 141
- Ingress Rate 143
- Limiting 143
- Egress Rate 143
- Ingress Rate Limiting 146
- Egress Rate Limiting 148
- Virtual LANs 149
- VLAN Overview 150
- Port-based 151
- Tagged VLAN 152
- VLAN Index 153
- VLAN Name 153
- Tagged and Untagged Ports 153
- Port VLAN Identifier (PVID) 153
- General Rules for 154
- Creating a 154
- Assign Ports to a VLAN Mode 155
- Chapter 13: Virtual LANs 156
- Tagged VLAN Configuration 157
- Modify a Tagged 158
- Delete a Tagged 160
- Tagged VLAN Port Settings 162
- Port-Based VLAN Configuration 164
- Modify a Port 165
- Based VLAN 165
- Chapter 14 167
- Overview and Guidelines 168
- General Configuration 169
- Port Settings 170
- Time Settings 172
- Chapter 14: GVRP 174
- Chapter 15 175
- Egress Queue vs 177
- Packet Priority 177
- Prioritizing 178
- Untagged Packets 178
- Queue Scheduling Algorithm 185
- Advanced Features 187
- SNMPv1 and v2c 189
- SNMPv1 and SNMPv2c Overview 190
- Trap Receiver Attributes 191
- Activate SNMP Interface 192
- Create User and 193
- Group Names 193
- Modify User and 194
- Delete User and 195
- SNMP Community Strings 196
- SNMP Traps 198
- Modify a Trap 199
- Host Table Entry 199
- Delete a Trap 199
- Chapter 16: SNMPv1 and v2c 200
- Chapter 17 201
- SNMPv3 Privacy 203
- Protocol 203
- SNMPv3 MIB 203
- SNMPv3 User and Group Names 206
- Modifying 207
- SNMPv3 User 207
- Deleting SNMPv3 208
- User and Group 208
- SNMPv3 View Names 209
- Chapter 17: SNMPv3 210
- SNMPv3 View 211
- View Names 211
- SNMPv3 View Table 212
- SNMPv3 Traps 215
- Access Control Configuration 217
- Classifier 219
- Modifying a 221
- Deleting a 222
- Profile Action 224
- Modifying Profile 225
- Deleting a Profile 226
- In-Profile Action 227
- Modifying an In 229
- Deleting an In 230
- Out-Profile Action 231
- Modify Out 233
- Delete Out 234
- Port List 235
- “Create Policy,” next 238
- “Modify Policy” on page 240 238
- “Delete Policy” on page 241 238
- Policy Sequence Status 243
- Chapter 19 245
- Enable and Disable RMON 247
- Port Statistics 248
- Histories 250
- Chapter 19: RMON 252
- Voice VLAN 257
- Dynamic Auto 259
- Detection vs 259
- Static Ports 259
- Chapter 20: Voice VLAN 260
- OUI Setting 265
- Modify OUI 266
- Delete OUI 266
- Security 267
- Port Access Control 268
- Port Access 269
- Chapter 21: Security 270
- RADIUS Client 273
- Radius Client 274
- Dial-in User 276
- Modify a Dial-in User 277
- Delete a Dial-in User 278
- Destination MAC Filter 279
- Destination MAC 280
- Power Over Ethernet (PoE) 283
- PoE Configuration 286
- DHCP Snooping 289
- DHCP with 291
- Option 82 291
- Chapter 23: DHCP Snooping 294
- VLAN Setting 295
- Binding Database 299
- Chapter 24 303
- Global Configuration 305
- Enabling or 306
- Disabling LLDP 306
- Displaying 307
- Information 307
- Setting Port 307
- Chapter 24: LLDP 308
- Neighbors Information 309
- Network Statistics 311
- Traffic Comparison Statistics 313
- Error Group Statistics 316
- Historical Status Charts 318
- Section IV 321
- Chapter 26 323
- File Upload 329
- File Download 331
- Cable Diagnostics 335
- Chapter 27: Cable Diagnostics 336
- Rebooting the AT-GS950/48PS 337
- Switch Reboot 338
- Disabling Factory 342
- Default Reset 342
- Enabling Factory 344
- Pinging a Remote System 347
- MSTP Overview 349
- Resolving VLAN 352
- Fragmentation 352
- Multiple VLANs 353
- Assigned to an 353
- Appendix A: MSTP Overview 354
- VLAN and MSTI Associations 356
- Ports in Multiple MSTIs 357
- MST Region 360
- Guidelines 360
- Associating VLANs to MSTIs 363
- Summary of Guidelines 367
- Appendix B 369
- Parameter 376
- Default Setting 376
- Specifications 376
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-GS950/48PS
Hardware De La Computadora Allied-telesis AT-UWC Wireless LAN Controller Manual de usuario
(33 paginas)
(33 paginas)
Hardware De La Computadora Allied-telesis AT-2911GP Network Adapters Manual de usuario
(152 paginas)
(152 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales