Allied-telesis AT-S84 Manual de usuario Pagina 275
- Pagina / 326
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-S84 Management Software User’s Guide
Section II: Web Browser Interface 275
2. In the STP Status column for the port you want to configure, select the
STP status from the list, either Enable or Disable.
3. In the Priority column for the port you want to configure, type a number
for the port priority.
Port priority is described in “Port Priority” on page 148.
4. In the Path Cost column for the port you want to configure, type a
number for the Path Cost.
Path cost is described in “Path Costs and Port Costs” on page 147.
5. Click Apply.
6. To configure all of the ports to the same settings, in the All row,
configure one, two, or all of the following settings: STP Status, Priority,
and Path Cost. Click Apply.
Configuring the
Advanced RSTP
Port Settings
To configure the advanced RSTP port settings, perform the following
procedure:
1. From the Basic Config menu, select Rapid Spanning Tree > RSTP
Adv. Port Config.
- Management 1
- Software 1
- User’s Guide 1
- Contents 3
- Contacting Allied Telesis 15
- Overview 17
- Management Overview 18
- Local Connection 19
- Remote Connection 20
- Management Access Level 21
- Chapter 1: Overview 22
- Using the Menus Interface 23
- Interface 25
- Enter system name> 37
- Enter system location> 37
- Enter system contact> 37
- Enter current password> 40
- Enter old password> 40
- Enter new password> 40
- Retype new password> 41
- Viewing Switch Information 47
- Rebooting the Switch 50
- Enter new timeout value> 53
- Figure 14. Ping Results 54
- Chapter 4 59
- SNMP Overview 60
- Default SNMP 61
- Community 61
- Chapter 4: SNMP 62
- Enabling Authentication Traps 63
- Enter read community name> 64
- Modifying a Trap 66
- Receiver 66
- Deleting a Trap 67
- Chapter 5: Port Configuration 70
- Enabling or Disabling a Port 72
- Enter new mode for port 73
- (a/h/H/F/f/T)> 73
- (E/D)> 75
- Port Trunking Overview 82
- LACP Trunks 84
- LACP Port 85
- Priority 85
- Parameter 85
- Modifying a Port 90
- Enter trunk group number> 96
- Set trunk group 96
- status (A/P/M/D)> 96
- Port Mirroring Overview 98
- Chapter 7: Port Mirroring 100
- Virtual LANs and GVRP 103
- VLAN Features 104
- VLAN Overview 106
- Incoming Frames 107
- Tagged Port Members 107
- Untagged Port Members 107
- Outgoing Frames 108
- AT-9000/24 109
- Tagged VLAN 111
- Working with VLANS 113
- Configuring the 116
- Port PVID 116
- Displaying the 117
- Changing the VLAN Name 119
- Enter VLAN ID > 120
- Resetting to the 121
- Default VLAN 121
- Enabling or 123
- Disabling GVRP 123
- Quality of Service (QoS) 125
- QoS Overview 126
- Configuring CoS 132
- Enter queue for trunk group 135
- >> 135
- IGMP Snooping 137
- IGMP Snooping Overview 138
- Configuring IGMP 140
- Enter age out time> 141
- Viewing the Multicast Groups 142
- Chapter 10: IGMP Snooping 144
- Chapter 11 145
- RSTP Overview 146
- Path Costs and Port Costs 147
- Port Priority 148
- Point-to-Point and Edge Ports 149
- Point-to-Point Ports 150
- (Full-duplex Mode) 150
- Mixed STP and 151
- RSTP Networks 151
- Rapid Spanning 152
- Tree and VLANs 152
- Enabling or Disabling RSTP 153
- Enter bridge priority> 156
- Enter bridge hello time> 156
- Enter bridge maximum age> 157
- Configuring STP Compatibility 158
- Basic RSTP Port 159
- Settings 159
- Advanced RSTP 161
- Port Settings 161
- Displaying the RSTP Topology 164
- 802.1x Network Access Control 167
- Authentication 169
- Authenticator 169
- Network Access 171
- Guidelines 171
- Switch A 173
- Switch B 173
- Enter port number> 175
- Enter NAS ID > 175
- Chapter 13 179
- RADIUS Overview 180
- Configuring the RADIUS Server 181
- Broadcast Storm Control 185
- Working With System Files 189
- Enter file name> 192
- Enter retry count> 192
- Download file? (Y/N)> 192
- Uploading the 193
- Configuration 193
- Downloading a 195
- Section II 197
- Chapter 16 199
- Switch’s IP Address 200
- Web Browser Tools 203
- Basic Switch Parameters 205
- 3. Click Apply 210
- Server and SNMP settings 212
- Configuring SNTP 216
- Viewing System Information 217
- Rebooting a Switch 219
- Pinging a Remote System 220
- Viewing the System Log 222
- Port Configuration 225
- Displaying Port Statistics 232
- Chapter 19 235
- Chapter 19: SNMP 236
- Working with Trap Receivers 238
- Port Trunking 239
- Setting Up a Port Trunk 240
- Disabling a Port 241
- Setting Up an LACP Trunk 242
- Verifying the 243
- LACP Group 243
- Disabling an 244
- LACP Trunk 244
- Port Mirroring 245
- Configuring Port Mirroring 246
- Disabling Port Mirroring 247
- Chapter 21: Port Mirroring 248
- Virtual LANs 249
- Creating a VLAN 250
- Chapter 22: Virtual LANs 252
- Displaying the VLANs 255
- Modifying a VLAN 256
- Deleting a VLAN 258
- Deleting All VLANs 259
- Enabling or Disabling GVRP 260
- Chapter 24 267
- Chapter 24: IGMP 270
- Chapter 25 271
- Basic RSTP Configuration 272
- Chapter 25: RSTP 276
- Viewing the RSTP Topology 278
- Chapter 27 285
- Configuring the RADIUS Client 286
- Working with System Files 289
- Section III 295
- Formatting 299
- Conventions 299
- User EXEC 300
- Command Mode 300
- Privileged EXEC 301
- 302 Section I: Basic Features 302
- Port Mirroring Example 304
- VLAN Example 306
- Section I: Basic Features 307 307
- Command Formatting 308
- Section I: Basic Features 309 309
- 310 Section I: Basic Features 310
- AT-S84 Default Settings 311
- Basic Switch Default Settings 312
- SNMP Default Settings 314
- Quality of Service 316
- RSTP Default Settings 318
- Settings Default 320
- Server IP Address 0.0.0.0 320
- Response Time 10 seconds 320
- Maximum Retransmissions 3 320
- Threshold Low 321
- 322 Section I: Basic Features 322
Relacionado con productos y manuales para Hardware De La Computadora Allied-telesis AT-S84
(514 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales