Allied Telesis AT-2872SX Manual de usuario

613-001261 Rev. AGigabit EthernetFiber ExpressCard ModuleAT-2872SXInstallation and User’s Guide

Tables10

11PrefaceThis guide contains instructions on how to install the AT-2872SX Gigabit Ethernet Fiber ExpressCard Module on a laptop computer. It also desc

Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-2872 SX Gigabit Ethernet Fiber ExpressCardTM Interface User’s Guide13Where to Find Web-based Documentation and DriversThe product documentation for

Preface14Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate infor

15Chapter 1Introducing the AT-2872SX Gigabit Ethernet Fiber ExpressCard ModuleThis chapter provides an introduction to the Allied Telesis AT-2872SX Gi

Chapter 1: Introducing the AT-2872SX Gigabit Ethernet Fiber ExpressCard Module16Functional DescriptionThe AT-2872SX is a highly integrated Gigabit Eth

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide17NoteThe AT-2872SX ExpressCard module is not shipped with a software dr

Chapter 1: Introducing the AT-2872SX Gigabit Ethernet Fiber ExpressCard Module18Hardware FeaturesThe following list of hardware features for the AT-28

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide19Supported Operating Systems The following list describes the supported

Copyright © 2010 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Introducing the AT-2872SX Gigabit Ethernet Fiber ExpressCard Module20Physical DescriptionThis section provides a physical description of th

21Chapter 2Installing the HardwareThis chapter contains the following sections: “Reviewing Safety Precautions” on page 22 “Pre-Installation Checklis

Chapter 2: Installing the Hardware22Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the switch

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide23WarningThe adapter is being installed in a system that operates with v

Chapter 2: Installing the Hardware24Pre-Installation ChecklistBefore you install the module, check the following list:1. Verify that your laptop is us

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide25Installing the ModuleThe following instructions describe how to instal

Chapter 2: Installing the Hardware26Figure 3. Selecting the ExpressCard Slot3. Use a pen and press the button toward the laptop and to the left. See F

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide27Figure 4. Pressing the ButtonFigure 5. Removing the Faceplate From PCI

Chapter 2: Installing the Hardware284. Remove the plate from the laptop. See Figure 6. Keep the plate in a safe place. You may need it for future use.

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide296. Applying even pressure at both corners of the module, push the modu

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class B, EN55022 Class B, VCCI Class B, C-TICK,

Chapter 2: Installing the Hardware30Connecting the Network CablesThe AT-2872SX ExpressCard module has two fiber optic connectors (transmit and receive

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide31NoteFor instructions that describe how to clean the fiber optic connec

Chapter 2: Installing the Hardware32

33Chapter 3Installing the Windows DriversThis chapter provides procedures to install and remove the driver software for all of the Windows Operating S

Chapter 3: Installing the Windows Drivers34Installing the Windows Driver Software This chapter describes how to install all of the following Windows O

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide35NoteA network device driver must be physically installed before the Br

Chapter 3: Installing the Windows Drivers362. From the driver directory, select the setup.exe file and Run. The Broadcom NetXtreme II Driver Installer

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide37Figure 10. License Agreement Page4. After you review the license agree

Chapter 3: Installing the Windows Drivers38Figure 11. Ready to Install the Program Page5. Click Install. The InstallShield Wizard Completed Page is di

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide39Figure 12. InstallShield Wizard Completed Page6. Click Finish to close

4Translated Safety StatementsImportant: The  symbol indicates that a translation of the safety statement is available in a PDF document titled “Trans

Chapter 3: Installing the Windows Drivers40NoteAll commands are case sensitive. NoteUser must “Run as Administrator” for Vista when using “msiexec” fo

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide41To perform a silent uninstall from within the installer source folder,

Chapter 3: Installing the Windows Drivers42Removing the Device DriversThis section discusses how to remove the device drivers. Windows XP To remove th

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide43Using the NetXtreme II Monolithic Driver The NetXtreme II, based on it

Chapter 3: Installing the Windows Drivers44In cases where adding the Windows 2000 monolithic driver still does not work, apply the following modificat

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide45Inserting the NetXtreme II Monolithic Driver in a WinPE 2.0 Image By d

Chapter 3: Installing the Windows Drivers465. To complete the customization of the image, prepare the image for deployment, type:peimg /prep c:\VistaP

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide47Once located, notice the following information:[params_utp]hkr, , req_

Chapter 3: Installing the Windows Drivers48Displaying or Changing the Properties of the Adapter To display or change the properties of the Broadcom ne

49Chapter 4Installing the Linux DriversThis chapter provides procedures to install the Linux drivers for the AT-2872SX ExpressCard moduleThis chapter

5ContentsPreface ...

Chapter 4: Installing the Linux Drivers50Introduction This chapter discusses the Linux drivers for the Broadcom NetXtreme II network adapters and desc

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide51bnx2i Driver The current version of the driver has been tested on 2.6.

Chapter 4: Installing the Linux Drivers52Installing Linux Driver Software There are two ways to install the Linux driver software— from the Source RPM

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide533. Install the newly built package which includes the driver and man p

Chapter 4: Installing the Linux Drivers54provided with your operating system. Building theDriver from theSource TAR FileThis procedure describes how t

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide55To configure the network protocol and address after building the drive

Chapter 4: Installing the Linux Drivers56Load and RunNecessary iSCSISoftwareComponentsBroadcom iSCSI Offload software suite consists of 3 kernel modul

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide57NoteOn 2.6 kernels, it is not necessary to bring down the eth# interfa

Chapter 4: Installing the Linux Drivers58Apply the updates by running the scripts provided in the supplemental tar file. For example, on Red Hat Enter

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide59NoteSome combinations of property values may conflict and result in fa

Contents6Appendix A: Specifications ...

Chapter 4: Installing the Linux Drivers60modprobe bnx2i en_tcp_dack=0Default: ENABLEDsq_size Use the “Configure SQ size” parameter to select the send-

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide61session recoveries induced by some older targets when iSCSI NOP-OUT an

Chapter 4: Installing the Linux Drivers62TSO: Enabled (on 2.6 kernels) WoL: Initial setting based on NVRAM's setting Checking DriverMessagesThe f

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide63Checking bnx2i Driver MessagesThe following are the most common bnx2i

Chapter 4: Installing the Linux Drivers64Target cannot be reached on any of the CNIC devices bnx2i: check route, cannot connect using cnicNetwork rout

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide65bnx2i: iscsi_error - invalid R2TSN fieldbnx2i: iscsi_error - invalid c

Chapter 4: Installing the Linux Drivers66Teaming withChannel BondingWith the Linux drivers, you can team adapters together using the bonding kernel mo

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide67Installing Open iSCSI User Applications Install and run the open-iscsi

Chapter 4: Installing the Linux Drivers68Binding iSCSI Target to Broadcom NX2 iSCSI Transport Name By default, the open-iscsi daemon connects to disco

AT-2872SX ExpressCard Fast Ethernet Fiber Module Installation and User’s Guide69iSCSI target discovery using 'SendTargets' iscsiadm -m disco

7FiguresFigure 1. AT-2872SX ExpressCard module ...

Chapter 4: Installing the Linux Drivers70

71Appendix ASpecificationsPhysical SpecificationsThis section provides the dimensions and weight of the module.Dimensions: 13.7 cm x 3.4 cm (5.4 in. x

Appendix A: Specifications72Performance SpecificationThe following performance specification apply to the AT-2872SX ExpressCard module:MTBF 1,650,000

73Appendix BCleaning Fiber Optic ConnectorsThe fiber optic connector consists of a fiber optic plug and its adapter. The end of the fiber optic cable

Appendix B: Cleaning Fiber Optic Connectors74Using a Cartridge-Type CleanerFiber optic cartridge cleaners are available from many vendors and are typi

AT-2872 SX Gigabit Ethernet Fiber ExpressCard Interface User’s Guide75NoteRub the ferrule tip on the cleaning surface in one direction only.3. When yo

Appendix B: Cleaning Fiber Optic Connectors76Using a SwabSpecially treated swabs (stick cleaners) are available for cleaning inside connector adapters

AT-2872 SX Gigabit Ethernet Fiber ExpressCard Interface User’s Guide773. If a fiber inspection scope is available, use the scope to inspect the connec

Appendix B: Cleaning Fiber Optic Connectors78

Figures8

9TablesTable 1: Safety Symbols ..............................