Allied-telesis AT-6101GP Manual de usuario

613-001673 Rev BAT-6101GP Power over Ethernet InjectorAT-6101GP PoE Injector Installation Guide

Tables6

7PrefaceThis guide contains the installation instructions for the AT-6101 PoE Injector Installation Guide. This preface contains the following section

Preface8Document ConventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that perf

AT-6101 PoE Injector Installation Guide9Allied Telesis Contact InformationIf you need assistance with this product, you may contact Allied Telesis tec

Preface10

11Chapter 1 OverviewThis chapter contains the following sections: “Features” on page 12 “Hardware Description” on page 14 “LEDs” on page 15

Chapter 1: Overview12FeaturesHere are the features of this product: AT-6101GP PoEInjectorThe major features of the AT-6101GP PoE Injector are: Power

AT-6101 PoE Injector Installation Guide13CableRequirementsThe cable requirements of the ports are given in Table 1. Port Pinouts Refer to Table 7 on p

Chapter 1: Overview14Hardware DescriptionThe AT-6101GP PoE Injector is shown in Figure 1.Figure 1. AT-6101GP PoE InjectorDATA IN Port: This port, show

AT-6101 PoE Injector Installation Guide15LEDsThe LEDs of the AT-6101GP PoE Injector are shown in Figure 3 and described in Table 2.Figure 3. AT-6101GP

Copyright © 2012 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Overview16

17Chapter 2InstallationYou may install the AT-6101GP PoE Injector on a table or on a wall. This chapter contains the following installation procedures

Chapter 2: Installation18Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to perform the installation proce

AT-6101 PoE Injector Installation Guide19WarningOnly trained and qualified personnel are allowed to install or replace this equipment.  E14Circuit Ov

Chapter 2: Installation20Choosing a Site for the AT-6101GP PoE InjectorObserve these guidelines when planning the installation of the AT-6101GP If yo

AT-6101 PoE Injector Installation Guide21Unpacking the AT-6101GP PoE InjectorThe AT-6101GP PoE Injector comes with the items listed in Table 4. Verify

Chapter 2: Installation22Installation ProceduresDepending on where you install the unit. perform the following procedures when installing the AT-6101G

AT-6101 PoE Injector Installation Guide232. Install the two wall anchors into the wall at the locations marked in the previous step. The anchors requi

Chapter 2: Installation24AC Power CordInstallationDepending on your installation, connect the AC power cord as shown in Figure 8 (table top installati

25Chapter 3TroubleshootingThis chapter contains suggestions on how to troubleshoot the installation of the AT-6101GP PoE Injector if a problem occurs.

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI EmissionsFCC Class B, CISPR 22 Class B, EN55022 Class B, VCCI

Chapter 3: Troubleshooting26

27Appendix ATechnical SpecificationsPhysical SpecificationsEnvironmental SpecificationsPower SpecificationsTable 3. Physical SpecificationsDimensions

Appendix A: Technical Specifications28CertificationsRJ-45 Twisted Pair Port PinoutsFigure 10 illustrates the pin layout of the RJ-45 connectors and po

AT-6101 PoE Injector Installation Guide29Table 8 lists the pin signals when a port operating at 1000 Mbps.Table 8. Pin Signals for 1000 MbpsPinout Pai

Appendix A: Technical Specifications30

Chapter : 4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Tr

1Preface ...

Contents2

3List of FiguresFigure 1. AT-6101GP PoE Injector ...

Figures4

5Table 1. Twisted Pair Cable for the 10/100/1000Base-T Ports ......................